Transverse Stiffener Requirements for Shear Postbuckling of Cold-Formed Steel Channels
Publication: Journal of Structural Engineering
Volume 146, Issue 8
Abstract
The enhanced shear strength of transversely stiffened shear panels compared to the strengths of the unstiffened has been well recognized in the Specification for Structural Steel Buildings (AISC 360) and the North American Specification for the Design of Cold-Formed Steel Structural Members (AISI S100). The requirements for the transverse stiffeners to secure such strength enhancement was similar in early versions of the two specifications, but the Specification for Structural Steel Buildings has recently adopted a whole new approach to reflect more closely the actual mechanistic behavior of stiffeners in the context of steel plate girders. The paper presents a series of shear tests on cold-formed steel beams with various transverse stiffener sizes followed by finite-element nonlinear collapse simulation to demonstrate the applicability of transverse stiffeners in the context of cold-formed steel members. The experimental series consists of six tests on 200-mm-deep C-shaped sections having angle intermediate transverse stiffeners screw-fastened to the web also reveals the conservatism of the transverse stiffener design rules in the AISI S100-16 specification. Based upon the experimental and numerical results, the paper recommends the adoption of the corresponding provisions taken from the AISC 360-16 specification.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding provided by the Australian Research Council Discovery Project Grant DP160104640 has been used to perform this project. The first author is supported by the University of Sydney International Scholarship.
References
AASHTO. 2017. LRFD bridge design specifications. Washington, DC: AASHTO.
AISC. 2005. Specification for structural steel buildings. Chicago: AISC.
AISC. 2016. Specification for structural steel buildings. Chicago: AISC.
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. Washington, DC: AISI.
Basler, K. 1961. “Strength of plate girders in shear.” J. Struct. Div. 87 (7): 151–180.
Bleich, F. 1952. Buckling strength of metal structures, edited by H. Bleich. New York: McGraw-Hill.
CEN (European Committee for Standardization). 2006. Eurocode 3: Design of steel structures—Part 1–3: General rules—Supplementary rules for cold-formed members and sheeting. EN 1993–1-3. Brussels, Belgium: CEN.
Hendy, C. R., and F. Presta. 2008. “Transverse web stiffeners and shear moment interaction for steel plate girder bridges.” In Proc., 7th Int. Conf. on Steel Bridges, 13–26. Braga, Portugal: Univ. of Minho.
Kim, Y. D., and D. W. White. 2013. “Transverse stiffener requirements to develop the shear buckling and post-buckling resistance of steel I-girders.” J. Struct. Eng. 140 (4): 04013098. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000867.
Levin, L. R., and C. W. Sandlin. 1949. Strength analysis of stiffened thick beam webs. Langley Field, VA: National Advisory Committee for Aeronautics.
Pham, C. H., and G. J. Hancock. 2012a. “Direct strength design of cold-formed C-sections for shear and combined actions.” J. Struct. Eng. 138 (6): 759–768. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000510.
Pham, C. H., and G. J. Hancock. 2012b. “Tension field action for cold-formed sections in shear.” J. Constr. Steel Res. 72 (May): 168–178. https://doi.org/10.1016/j.jcsr.2011.12.001.
Pham, S. H. 2019. “Design of cold-formed steel beams with holes and transverse stiffeners in shear.” Ph.D. thesis, School of Civil Engineering, Univ. of Sydney.
Pham, S. H., C. H. Pham, C. A. Rogers, and G. J. Hancock. 2019a. “Experimental validation of the direct strength method for shear spans with high aspect ratios.” J. Constr. Steel Res. 157 (Jun): 143–150. https://doi.org/10.1016/j.jcsr.2019.02.018.
Pham, S. H., C. H. Pham, C. A. Rogers, and G. J. Hancock. 2019b. “Shear strength experiments and design of cold-formed steel channels with web holes.” J. Struct. Eng. 146 (1): 04019173. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002464.
Phan, D. K., and K. J. R. Rasmussen. 2018. “Cold-formed steel bolted and screw-fastened connections in shear.” In Proc., 8th Int. Conf. on Thin-Walled Structures. Lisbon, Portugal: Univ. of Lisbon.
Sandlin, C. W. 1948. Strength tests of shear webs with uprights not connected to the flanges. Langley Field, VA: National Advisory Committee for Aeronautics.
Schafer, B. W., Z. Li, and C. D. Moen. 2010. “Computational modeling of cold-formed steel.” Thin Walled Struct. 48 (10–11): 752–762. https://doi.org/10.1016/j.tws.2010.04.008.
Standards Australia. 2018. Cold-formed steel structures. AS 4600. Sydney, Australia: Standards Australia.
Stein, M., and R. W. Fralich. 1949. Critical shear stress of infinitely long, simply supported plate with transverse stiffeners. Langley Field, VA: National Advisory Committee for Aeronautics.
White, D. W., and M. G. Barker. 2008. “Shear resistance of transversely stiffened steel I-girders.” J. Struct. Eng. 134 (9): 1425–1436. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:9(1425).
White, D. W., M. G. Barker, and A. Azizinamini. 2008. “Shear strength and moment-shear interaction in transversely stiffened steel I-girders.” J. Struct. Eng. 134 (9): 1437–1449. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:9(1437).
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Jun 21, 2019
Accepted: Feb 19, 2020
Published online: May 23, 2020
Published in print: Aug 1, 2020
Discussion open until: Oct 23, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.