Modeling Hysteretic Behavior of Lateral Load-Resisting Elements in Traditional Chinese Timber Structures
Publication: Journal of Structural Engineering
Volume 146, Issue 5
Abstract
Dou-gong connections and mortise-tenon jointed traditional timber frames are widely used in traditional Chinese timber structures to resist lateral loads. Such elements exhibit strong nonlinearity in unloading routes, especially at drifts beyond the peak load. This paper proposes a multifunctional model for the hysteretic behavior of dou-gong connections and mortise-tenon jointed timber frames. The proposed model is capable of capturing the asymmetric envelopes in opposite loading directions via two sets of ten adjustable parameters and utilizes Bézier curves for the unloading routes and linear pinching routes via nine parameters. The model validity was discussed in comparison with two commonly used models—the SAWS and the Pinching4 models—based on the reversed cyclic test results of typical traditional Chinese dou-gong connections and mortise-tenon jointed timber frames. The use of the Bézier curves and two different unloading patterns in the proposed model was found to be more reasonable than the piecewise linear unloading routes used in the SAWS and Pinching4 models. The proposed model agrees better with the test results in both the load-displacement hysteretic curves and the energy dissipation. The case study on the seismic fragility of traditional Chinese mortise-tenon jointed timber frames confirms the computation stability of the proposed model by the smooth hysteretic curves established based on the seismic accelerations and the resulting displacements.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was financially supported by the National Natural Science Foundation of China (Grant No. 51878477), the Scientific and Technology Committee of Shanghai Metropolitan (Grant No. 13231201703), and the China Scholarship Council (No. 201706260111).
References
ASTM. 2009. Standard test methods for small clear specimens of timber. ASTM D143. West Conshohocken, PA: ASTM.
Baker, J. W. 2015. “Efficient analytical fragility function fitting using dynamic structural analysis.” Earthquake Spectra 31 (1): 579–599. https://doi.org/10.1193/021113EQS025M.
Boudaud, C., J. Humbert, J. Baroth, S. Hameury, and L. Daudeville. 2015. “Joints and wood shear walls modeling. II: Experimental tests and FE models under seismic loading.” Eng. Struct. 101 (Oct): 743–749. https://doi.org/10.1016/j.engstruct.2014.10.053.
Crayssac, E., X. Song, Y. Wu, and K. Li. 2018. “Lateral performance of mortise-tenon jointed traditional timber frames with wood panel infill.” Eng. Struct. 161 (Apr): 223–230. https://doi.org/10.1016/j.engstruct.2018.02.022.
FEMA. 2000. Prestandard and commentary for the seismic rehabilitation of buildings. FEMA 365. Washington, DC: FEMA.
Foliente, G. C. 1995. “Hysteresis modeling of wood joints and structural systems.” J. Struct. Eng. 121 (6): 1013–1022. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:6(1013).
Folz, B., and A. Filiatrault. 2001. SAWS version 1.0: A computer program for the seismic analysis of woodframe structures. La Jolla, CA: Dept. of Structural Engineering, Univ. of California, San Diego.
Folz, B., and A. Filiatrault. 2004. “Seismic analysis of woodframe structures. I: Model formulation.” J. Struct. Eng. 130 (9): 1353–1360. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:9(1353).
Fujita, K., N. Kawai, C. Minowa, M. Koshihihara, and K. Chiba. 2006. “Shaking table test and earthquake response monitoring of traditional Japanese Timber Pagoda.” In Proc., 9th World Conf. on Timber Engineering. Corvallis, OR: Oregon State Univ. Conference Services.
He, M., F. Lam, and R. O. Foschi. 2001. “Modeling three-dimensional timber light-frame buildings.” J. Struct. Eng. 127 (8): 901–913. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:8(901).
Huang, H., Y. Wu, Z. Li, Z. Sun, and Z. Chen. 2018. “Seismic behavior of Chuan-Dou type timber frames.” Eng. Struct. 167 (Jul): 725–739. https://doi.org/10.1016/j.engstruct.2017.10.072.
Humbert, J., C. Boudaud, J. Baroth, S. Hameury, and L. Daudeville. 2014. “Joints and wood shear walls modelling I: Constitutive law, experimental tests and FE model under quasi-static loading.” Eng. Struct. 65 (Apr): 52–61. https://doi.org/10.1016/j.engstruct.2014.01.047.
Krawinkler, H., F. Parisi, L. Ibarra, A. Ayoub, and R. Medina. 2001. Vol. 102 of Development of a testing protocol for woodframe structures. Richmond, CA: Consortium of Universities for Research in Earthquake Engineering.
Li, J. 1103. Ying Zao Fa Shi. Beijing: People’s Publishing House.
Li, M., and F. Lam. 2009. “Lateral performance of mortise-tenon jointed traditional timber frames with wood panel infill.” J. Struct. Eng. 135 (2): 178–186. https://doi.org/10.1061/(ASCE)0733-9445(2009)135:2(178).
Li, M., F. Lam, R. O. Foschi, S. Nakajima, and T. Nakagawa. 2012a. “Seismic performance of post and beam timber buildings. Part I: Model development and verification.” J. Wood Sci. 58 (1): 20–30. https://doi.org/10.1007/s10086-011-1219-5.
Li, M., F. Lam, R. O. Foschi, S. Nakajima, and T. Nakagawa. 2012b. “Seismic performance of post-and-beam timber buildings. Part II: Reliability evaluations.” J. Wood Sci. 58 (2): 135–143. https://doi.org/10.1007/s10086-011-1232-8.
Li, X., J. Zhao, G. Ma, and W. Chen. 2015. “Experimental study on the seismic performance of a double-span traditional timber frame.” Eng. Struct. 98 (Sep): 141–150. https://doi.org/10.1016/j.engstruct.2015.04.031.
Lowes, L. N., N. Mitra, and A. Altoontash. 2003. A beam-column joint model for simulating the earthquake response of reinforced concrete frames.. Berkeley, CA: Pacific Earthquake Engineering Research Center, Univ. of California.
Luo L., X. B. Song, H. B. Wu, and J. N. Cai. 2016. “Experimental study on mechanical performance of wood pegged semi mortise and tenon connections.” In Proc., World Conf. of Timber Engineering. Vienna, Austria: DAAAM International Vienna.
McKenna, F., G. L. Fenves, and M. H. Scott. 2000. Open system for earthquake engineering simulation. Berkeley, CA: Univ. of California, Berkeley.
Meireles, H., R. Bento, S. Cattari, and S. Lagomarsino. 2012. “A hysteretic model for ‘frontal’ walls in Pombalino buildings.” Bull. Earthquake Eng. 10 (5): 1481–1502. https://doi.org/10.1007/s10518-012-9360-0.
Pei, S., M. Popovski, and J. W. van de Lindt. 2013. “Analytical study on seismic force modification factors for cross-laminated timber buildings.” Can. J. Civ. Eng. 40 (9): 887–896. https://doi.org/10.1139/cjce-2013-0021.
Richard, N., L. Daudeville, H. Prion, and F. Lam. 2002. “Timber shear walls with large openings: Experimental and numerical prediction of the structural behaviour.” Can. J. Civ. Eng. 29 (5): 713–724. https://doi.org/10.1139/l02-050.
Richard, N., M. Yasumura, and L. Davenne. 2003. “Prediction of seismic behavior of wood-framed shear walls with openings by pseudodynamic test and FE model.” J. Wood Sci. 49 (2): 145–151. https://doi.org/10.1007/s100860300023.
Rinaldin, G., C. Amadio, and M. Fragiacomo. 2013. “A component approach for the hysteretic behaviour of connections in cross-laminated wooden structures.” Earthquake Eng. Struct. Dyn. 42 (13): 2023–2042. https://doi.org/10.1002/eqe.2310.
Rinaldin, G., and M. Fragiacomo. 2016. “Non-linear simulation of shaking-table tests on 3-and 7-storey X-Lam timber buildings.” Eng. Struct. 113 (Apr): 133–148. https://doi.org/10.1016/j.engstruct.2016.01.055.
SGCMC (Shanghai Government Construction and Management Commission). 2013. Code for seismic design of buildings. DGJ08-9. Shanghai, China: Shanghai Government Construction and Management Commission.
Song, X., Y. Wu, L. Luo, and X. Gu. 2017. “Shaking table test on a traditional pavilion-style wooden pagoda.” J. Build. Struct. 38 (2): 10–19.
Wu, Y., X. Song, X. Gu, and L. Luo. 2018a. “Dynamic performance of a multi-story traditional Timber Pagoda.” Eng. Struct. 159 (Mar): 277–285. https://doi.org/10.1016/j.engstruct.2018.01.003.
Wu, Y., X. Song, and K. Li. 2018b. “Compressive and racking performance of eccentrically aligned dou-gong connections.” Eng. Struct. 175 (Nov): 743–752. https://doi.org/10.1016/j.engstruct.2018.08.054.
Xie, Q., L. Wang, L. Zhang, W. Hu, and T. Zhou. 2019. “Seismic behaviour of a traditional timber structure: shaking table tests, energy dissipation mechanism and damage assessment model.” Bull. Earthquake Eng. 17 (3): 1689–1714. https://doi.org/10.1007/s10518-018-0496-4.
Xie, Q., W. Xiang, B. Du, and P. Zheng. 2014. “Study on seismic behavior degradation of damaged ‘Dougong’ joint built with fork column of Chinese ancient timber structure.” China Civ. Eng. J. 47 (12): 49–55.
Xu, J., and J. D. Dolan. 2009a. “Development of nailed wood joint element in ABAQUS.” J. Struct. Eng. 135 (8): 968–976. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000030.
Xu, J., and J. D. Dolan. 2009b. “Development of a wood-frame shear wall model in ABAQUS.” J. Struct. Eng. 135 (8): 977–984. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000031.
Yuan, J., W. Chen, J. Wang, and Y. Shi. 2011. “Experimental research on bracket set models of Yingxian Timber Pagoda.” J. Build. Struct. 32 (7): 66–72.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Mar 1, 2019
Accepted: Oct 15, 2019
Published online: Feb 29, 2020
Published in print: May 1, 2020
Discussion open until: Jul 29, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.