Parametric Study for Performance-Based Fire Design of US Prototype Composite Floor Systems
Publication: Journal of Structural Engineering
Volume 145, Issue 5
Abstract
Design requirements for passive fire protection of steel structures in the United States are primarily based on prescriptive approaches. Yet performance-based design has gained attention in recent years for its potential to unlock design solutions that are robust, cost effective, and applicable to complex architectural configurations. For example, prior research has shown that fire protection on selected secondary beam elements in composite floor systems is not necessary due to the development of membrane action in the concrete slab during fire. In addition, the evaluation of a structure’s performance under realistic fire scenarios, required in a performance-based approach, is enabled by recent developments in advanced computational modeling. However, currently there are no systematic guidelines to determine the reliability of a performance-based fire engineering design. This study provides a comparative analysis of the fire performance of a floor system designed following prescriptive and performance-based approaches. The floor system is adopted from a prototype steel–concrete composite office building. Further, a parametric study is conducted to investigate the effects of several parameters on the thermal-mechanical response including the modeling approach, fire curves, applied gravity loads, and hazard scenarios. Performance is measured using survival time at the structural system level, but also with predefined thresholds in deflection and reinforcement bar temperature. The results demonstrate that the performance-based design is robust, and verification of safety is not dependent on a particular demand value or performance measure. Most importantly, the performance-based design shows resistance when subjected to natural fires with large percentage fractile of fire load as well as in multihazard post-blast fire situations.
Get full access to this article
View all available purchase options and get full access to this article.
References
AISC. 2003. Fire resistance of structural steel framing. Design guide 19. Chicago: AISC.
AISC. 2010. Steel construction manual. 13th ed. Chicago: AISC.
ASCE. 2010. Minimum design loads for buildings and other structures. ASCE/SEI 7. Reston, VA: ASCE.
ASCE. 2016. Minimum design loads for buildings and other structures. ASCE/SEI 7. Reston, VA: ASCE.
Bailey, C. G. 2004. “Membrane action of slab/beam composite floor systems in fire.” Eng. Struct. 26 (12): 1691–1703. https://doi.org/10.1016/j.engstruct.2004.06.006.
Bailey, C. G., and D. B. Moore. 2000. “The structural behaviour of steel frames with composite floor slabs subject to fire: Part 1: Theory.” Struct. Eng. 78 (11): 19–27.
Cadorin, J. F., and J. M. Franssen. 2003. “A tool to design steel elements submitted to compartment fires—OZone V2. Part 1: Pre- and post-flashover compartment fire model.” Fire Saf. J. 38 (5): 395–427. https://doi.org/10.1016/S0379-7112(03)00014-6.
Cadorin, J. F., D. Pintea, J. C. Dotreppe, and J. M. Franssen. 2003. “A tool to design steel elements submitted to compartment fires—OZone V2. Part 2: Methodology and application.” Fire Saf. J. 38 (5): 429–451. https://doi.org/10.1016/S0379-7112(03)00015-8.
CEN (European Committee for Standardization). 2004. Eurocode 2: Design of concrete structures—Part 1-2: General rules—Structural fire design. EN 1992-1-2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2002. Eurocode 1: Actions on structures—Part 1 and 2: General actions—Actions on structures exposed to fire. Brussels: CEN.
CEN (European Committee for Standardization). 2005. Eurocode 3: Design of steel structures—Part 1-2: General rules—Structural fire design. EN 1993-1-2. Brussels, Belgium: CEN.
El Ghor, A. H., and E. G. Hantouche. 2017. “Thermal creep mechanical-based modeling for flush endplate connections in fire.” J. Constr. Steel Res. 136 (Sep): 11–23. https://doi.org/10.1016/j.jcsr.2017.04.022.
Elhami Khorasani, N. 2015. “A probabilistic framework for multi-hazard evaluations of buildings and communities subject to fire and earthquake scenarios.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Princeton Univ.
Elhami Khorasani, N., M. Garlock, and P. Gardoni. 2016. “Probabilistic performance-based evaluation of a tall steel moment resisting frame under fire following earthquake.” J. Struct. Fire Eng. 7 (3): 193–216. https://doi.org/10.1108/JSFE-09-2016-014.
Elhami Khorasani, N., C. Fang, and T. Gernay. 2017. “Comparative fire analysis of steel-concrete composite buildings designed following performance-based and U.S. prescriptive approaches.” In Proc., Applications of Structural Fire Engineering Conf. Boca Raton, FL: CRC Press.
Ellingwood, B. R. 2005. “Load combination requirements for fire-resistant structural design.” J. Fire Prot. Eng. 15 (1): 43–61. https://doi.org/10.1177/1042391505045582.
Ellingwood, B. R., R. Smilowitz, D. O. Dusenberry, D. Duthinh, H. S. Lew, and N. J. Carino. 2007. Best practices for reducing the potential for progressive collapse in buildings. Gaithersburg, MD: National Institute of Standards and Technology.
Fike, R., and V. Kodur. 2011. “Enhancing the fire resistance of composite floor assemblies through the use of steel fiber reinforced concrete.” Eng. Struct. 33 (10): 2870–2878. https://doi.org/10.1016/j.engstruct.2011.06.011.
Fischer, E. C., and A. H. Varma. 2017. “Fire resilience of composite beams with simple connections: Parametric studies and design.” J. Constr. Steel Res. 128 (Jan): 119–135. https://doi.org/10.1016/j.jcsr.2016.08.004.
Franssen, J. M., and T. Gernay. 2017. “Modelling structures in fire with SAFIR®: Theoretical background and capabilities.” J. Struct. Fire Eng. 8 (3): 300–323. https://doi.org/10.1108/JSFE-07-2016-0010.
Garlock, M. E., and S. Selamet. 2010. “Modeling and behavior of steel plate connections subject to various fire scenarios.” J. Struct. Eng. 136 (7): 897–906. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000179.
Gernay, T., N. Elhami Khorasani, and M. Garlock. 2016. “Fire fragility curves for steel buildings in a community context: A methodology.” Eng. Struct. 113 (Apr): 259–276. https://doi.org/10.1016/j.engstruct.2016.01.043.
Gernay, T., and J. M. Franssen. 2012. “A formulation of the Eurocode 2 concrete model at elevated temperature that includes an explicit term for transient creep.” Fire Saf. J. 51 (Jul): 1–9. https://doi.org/10.1016/j.firesaf.2012.02.001.
Gernay, T., and J. M. Franssen. 2015. “A plastic-damage model for concrete in fire: Applications in structural fire engineering.” Fire Saf. J. 71 (Jan): 268–278. https://doi.org/10.1016/j.firesaf.2014.11.028.
Gernay, T., A. Millard, and J. M. Franssen. 2013. “A multiaxial constitutive model for concrete in the fire situation: Theoretical formulation.” Int. J. Solids Struct. 50 (22–23): 3659–3673. https://doi.org/10.1016/j.ijsolstr.2013.07.013.
Gillie, M., A. S. Usmani, and J. M. Rotter. 2002. “A structural analysis of the Cardington British steel corner test.” J. Constr. Steel Res. 58 (4): 427–442. https://doi.org/10.1016/S0143-974X(01)00066-9.
Green, M., N. A. Butterworth, I. W. Burgess, R. J. Plank, and B. H. Fedra. 2003. “Practical case studies in performance-based structural fire engineering design.” In Proc., ASCE Specialty Conf.: Designing Structures for Fire, 259–266. Chicago: American Institute of Steel Construction.
Hantouche, E. G., N. H. Abboud, M. A. Morovat, and M. D. Engelhardt. 2016. “Analysis of steel bolted double angle connections at elevated temperatures.” Fire Saf. J. 83 (Jul): 79–89. https://doi.org/10.1016/j.firesaf.2016.05.002.
Hopkin, D., R. Van Coile, and D. Lange. 2017. Certain uncertainty-demonstrating safety in fire engineering design and the need for safety targets. Gaithersburg, MD: Society of Fire Protection Engineers.
Huang, Z., I. W. Burgess, and R. J. Plank. 2003. “Modeling membrane action of concrete slabs in composite buildings in fire. II: Validations.” J. Struct. Eng. 129 (8): 1103–1112. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:8(1103).
IBC. 2012. International building code. Country Club Hills, IL: International Code Council.
Iqbal, S., and R. Harichandran. 2010. “Capacity reduction and fire load factors for design of steel members exposed to fire.” J. Struct. Eng. 136 (12): 1554–1562. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000256.
Isolatek. 2014. Isolatek international product manual. Stanhope, NJ: Isolatek International.
Kordosky, A. 2017. “Experimental and computational investigation of composite beam response to fire.” Master of Science Dissertation, Dept. of Civil and Environmental Engineering, Lehigh Univ.
Lelli, L., and J. Loutan. 2017. “Advanced analyses of the membrane action of composite slabs under natural fire scenarios: A case study of the JTI headquarters.” J. Struct. Fire Eng. 9 (1): 77–90. https://doi.org/10.1108/JSFE-12-2016-0020.
Lim, L., A. Buchanan, P. Moss, and J. M. Franssen. 2004. “Numerical modelling of two-way reinforced concrete slabs in fire.” Eng. Struct. 26 (8): 1081–1091. https://doi.org/10.1016/j.engstruct.2004.03.009.
Magenes, L., T. J. Mander, and M. A. Morovat. 2017. “Effects of blast-induced permanent deflections on the performance of load-bearing steel elements in fire.” In Proc. Structures Congress, 66–76. Reston, VA: ASCE.
Morovat, M. A., A. H. El Ghor, and E. G. Hantouche. 2018. “Time-dependent response of flush endplate connections to fire temperatures.” J. Struct. Eng. 144 (4): 04018023. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002006.
Moss, P. J., and G. Charles Clifton. 2004. “Modelling of the Cardington LBTF steel frame building fire tests.” Fire Mater. 28 (2–4): 177–198. https://doi.org/10.1002/fam.868.
NIST (National Institute of Standards and Technology). 2016. CFAST—Consolidated model of fire growth and smoke transport (Version 7). Volume 2: User’s guide. Gaithersburg, MD: National Institute of Standards and Technology.
O’Conner, M. A., B. R. Kirby, and D. M. Martin. 2003. “Behaviour of a multi-storey composite steel framed building in fire.” Struct. Eng. 81 (2): 27–36.
Plank, R. 2013. “Performance based fire engineering in the UK.” Int. J. High-Rise Build. 2 (1): 1–9.
Sarraj, M., I. W. Burgess, J. B. Davison, and R. J. Plank. 2007. “Finite element modelling of steel fin plate connections in fire.” Fire Saf. J. 42 (6–7): 408–415. https://doi.org/10.1016/j.firesaf.2007.01.007.
UFC (Unified Facilities Criteria). 2009. Design of buildings to resist progressive collapse. UFC 4-023-03. Washington, DC: US Dept. of Defense.
UL (Underwriters Laboratories, Inc.) 2003. Fire resistance directory, Vol. 1. Northbrook, IL: Underwriters Laboratories.
Vassart, O., C. G. Bailey, M. Hawes, A. Nadjai, W. I. Sims, B. Zhao, T. Gernay, and J. M. Franssen. 2012. “Large-scale fire test of unprotected cellular beam acting in membrane action.” Proc. Inst. Civ. Eng.: Struct. Build. 165 (7): 327–334.
Vassart, O., and B. Zhao. 2012. MACS+ for membrane action of composite structures in case of fire. Design guide. Luxemburg: ArcelorMittal.
Wald, F., L. S. da Silva, D. B. Moore, T. Lennon, M. Chladna, A. Santiago, M. Benes, and L. Borges. 2006. “Experimental behaviour of a steel structure under natural fire.” Fire Saf. J. 41 (7): 509–522. https://doi.org/10.1016/j.firesaf.2006.05.006.
Wang, Y. C. 2000. “An analysis of the global structural behaviour of the Cardington steel-framed building during the two BRE fire tests.” Eng. Struct. 22 (5): 401–412. https://doi.org/10.1016/S0141-0296(98)00127-8.
Yu, H., I. W. Burgess, J. B. Davison, and R. J. Plank. 2009. “Experimental investigation of the behaviour of fin plate connections in fire.” J. Constr. Steel Res. 65 (3): 723–736. https://doi.org/10.1016/j.jcsr.2008.02.015.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 145 • Issue 5 • May 2019
Copyright
©2019 American Society of Civil Engineers.
History
Received: Mar 2, 2018
Accepted: Oct 23, 2018
Published online: Feb 28, 2019
Published in print: May 1, 2019
Discussion open until: Jul 28, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.