A Cyclic Backbone Curve for Shear-Critical Reinforced Concrete Walls
This article has a reply.
VIEW THE REPLYPublication: Journal of Structural Engineering
Volume 145, Issue 4
Abstract
Backbone curves are used in seismic design standards as the basis for developing component models for nonlinear static and dynamic analysis. Herein, data from 240 tests of rectangular, barbell, and flanged shear-critical walls are assembled and analyzed to develop an improved cyclic backbone curve for use in nonlinear response-history analysis. Values of drift ratio and normalized lateral force at the control points on the cyclic backbone curve are identified. The effects of design parameters, including wall aspect ratio, axial load, day-of-test concrete compressive strength, vertical and horizontal web reinforcement ratio, reinforcement ratio in the boundary elements, and yield strength of reinforcement, on the coordinates of the control points are addressed. The accuracy of equations for peak shear strength is assessed using the collected test data.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was supported by the National Institute of Standard and Technology under Grant No. SB1341-13-CQ-0009 to conduct a comprehensive review of the generalized component models published in the current ASCE/SEI standard and relevant research, and develop recommendations for improvement (ATC-114 Project). This support is gratefully acknowledged. The work forming the basis for this publication was conducted pursuant to a contract with the National Institute of Standard and Technology. The substance of such work is dedicated to the public.
Disclaimer
The authors are solely responsible for the accuracy of statements or interpretations contained in this paper. The first and third authors served as independent consultants to the Applied Technology Council. No warranty is offered with regard to the results, findings, and recommendations contained herein, either by the National Institute of Standards and Technology, or the Applied Technical Council, its directors, members, or employees. These organizations and individuals do not assume any legal liability or responsibility for the accuracy, completeness, or usefulness of any of the information included in this publication.
References
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete and commentary. ACI 318. Farmington Hills, MI: ACI.
ASCE. 2006. Seismic rehabilitation of buildings. ASCE/SEI Standard 41. Reston, VA: ASCE.
ASCE. 2013. Seismic evaluation and retrofit of existing buildings. ASCE/SEI Standard 41. Reston, VA: ASCE.
Barda, F., J. M. Hanson, and W. G. Corley. 1977. “Shear strength of low-rise walls with boundary elements.” ACI Spec. Publ. 53: 149–202.
Deierlein, G. G., A. M. Reinhorn, and M. R. Willford. 2010. Nonlinear structural analysis for seismic design. Gaithersburg, MD: NIST.
Elwood, K. J., A. B. Matamoros, J. W. Wallace, D. E. Lehman, J. A. Heintz, A. D. Mitchell, M. A. Moore, M. T. Valley, L. N. Lowes, and C. D. Comartin. 2007. “Update to ASCE/SEI 41 concrete provisions.” Earthquake Spectra 23 (3): 493–523. https://doi.org/10.1193/1.2757714.
Epackachi, S., N. Sharma, A. S. Whittaker, and A. Hortacsu. 2018. “A cyclic backbone curve for squat reinforced concrete shear walls.” In Proc., 11th US National Conf. on Earthquake Engineering. Oakland, CA: Earthquake Engineering Research Institute.
FEMA. 1997a. NEHRP commentary on the guidelines for the seismic rehabilitation of buildings. FEMA 274. Washington, DC: FEMA.
FEMA. 1997b. NEHRP guidelines for the seismic rehabilitation of buildings. FEMA 273. Washington, DC: FEMA.
FEMA. 2000. Prestandard and commentary for the seismic rehabilitation of buildings. FEMA 356. Washington, DC: FEMA.
Gulec, C. K., and A. S. Whittaker. 2009. Performance-based assessment and design of squat reinforced concrete shear walls. MCEER-09-0010. Buffalo, NY: Univ. at Buffalo.
Gulec, C. K., and A. S. Whittaker. 2011. “Empirical equations for peak shear strength of low aspect ratio reinforced concrete walls.” ACI Struct. J. 108 (1): 80–89.
Gulec, C. K., A. S. Whittaker, and B. Stojadinovic. 2008. “Shear strength of squat rectangular reinforced concrete walls.” ACI Struct. J. 105 (4): 488–497.
Luna, B. N., J. P. Rivera, S. Epackachi, and A. S. Whittaker. 2018. Seismic response of low aspect ratio rein forced concrete shear walls for buildings and safety-related nuclear structures. MCEER-18-0002. Buffalo, NY: Univ. at Buffalo.
Luna, B. N., J. P. Rivera, and A. S. Whittaker. 2015. “Seismic behavior of low aspect ratio reinforced concrete shear walls.” ACI Struct. J. 112 (5): 593–603. https://doi.org/10.14359/51687709.
Mahin, S. A., and V. V. Bertero. 1976. “Problems in establishing and predicting ductility in a seismic design.” In Proc., Int. Symp. on Earthquake Structural Engineering, 613–628. Rolla, MO: Univ. of Missouri.
NIST. 2017. Recommended modeling parameters and acceptance criteria for nonlinear analysis in support of seismic evaluation, retrofit, and design. NIST GCR 17-917-45. Gaithersburg, MD: Applied Technology Council.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jan 17, 2018
Accepted: Aug 31, 2018
Published online: Jan 24, 2019
Published in print: Apr 1, 2019
Discussion open until: Jun 24, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.