Seismic Performance Assessment of Low-Ductility Concentrically Braced Frames
Publication: Journal of Structural Engineering
Volume 145, Issue 4
Abstract
Current US seismic design provisions allow structures in areas of lower seismicity (e.g., the Midwest and eastern North America) to be designed with modest seismic requirements as compared with the requirements that must be satisfied in areas of higher seismicity (e.g., western North America). Because of the reduced seismic detailing and proportioning requirements in these areas of moderate seismicity, seismic force–resisting systems (SFRSs) within these regions are classified as low-ductility, in contrast to the high-ductility systems common in areas of higher seismicity. Considering the prevalence of low-ductility concentrically braced frames (CBFs) in moderate seismic regions of the US, a thorough performance assessment of these low-ductility CBFs was conducted using detailed OpenSees building models and dynamic numerical simulations. A matrix of 12 buildings was assessed, which varied by number of stories (3, 6, and 9), system configuration (chevron and split-x), and system type [ CBF and ordinary CBF (OCBF)]. An additional set of six buildings was designed, using with modified seismic detailing and proportioning, to investigate an alternate prototype low-ductility SFRS with improved seismic performance. Using the established seismic performance evaluation framework, CBF systems did not pass, whereas all but one of the OCBF systems passed. All but one of the prototype CBF systems passed the seismic performance evaluation, and for the majority of cases, the weight-normalized performance was better than the corresponding OCBF systems.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This study was supported by the National Science Foundation (Grant No. CMMI-1207976) and the American Institute of Steel Construction. The first author was partially supported by a National Science Foundation Graduate Research Fellowship under Grant No. DGE-1144245. This work used the Extreme Science and Engineering Discovery Environment (XSEDE), which is supported by National Science Foundation Grant No. ACI-1548562. The opinions, findings, and conclusions in this paper are those of the authors and do not necessarily reflect the views of those acknowledged here.
References
Abolmaali, A., A. R. Kukreti, and H. Razavi. 2003. “Hysteresis behavior of semi-rigid double web angle steel connections.” J. Constr. Steel Res. 59 (8): 1057–1082. https://doi.org/10.1016/S0143-974X(03)00005-1.
AISC. 2010a. Seismic provisions for structural steel buildings. ANSI/AISC 341. Chicago: AISC.
AISC. 2010b. Specification for structural steel buildings. ANSI/AISC 360. Chicago: AISC.
ASCE. 2005. Minimum design loads for buildings and other structures. ASCE 7. Reston, VA: ASCE.
ASCE. 2013. Minimum design loads for buildings and other Structures. ASCE/SEI 7. Reston, VA: ASCE.
Bradley, C. R., L. A. Fahnestock, E. M. Hines, and J. G. Sizemore. 2017. “Full-scale cyclic testing of low-ductility concentrically-braced frames.” J. Struct. Eng. 143 (6): 04017029. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001760.
Charney, F. A. 2008. “Unintended consequences of modeling damping in structures.” J. Struct. Eng. 134 (4): 581–592. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:4(581).
Clifton, C., M. Bruneau, G. MacRae, R. Leon, and A. Fussell. 2011. “Steel structures damage from the Christchurch earthquake series of 2010 and 2011.” Bull. New Zealand Soc. Earthquake Eng. 44 (4): 297–318.
FEMA (Federal Emergency Management Agency). 2009. Quantification of building seismic performance factors. FEMA P695. Washington, DC: FEMA.
Hines, E. M., M. E. Appel, and P. J. Cheever. 2009. “Collapse performance of low-ductility chevron braced steel frames in moderate seismic regions.” Eng. J. 46 (3): 149.
Hines, E. M., L. G. Baise, and S. S. Swift. 2011. “Ground-motion suite selection for eastern North America.” J. Struct. Eng. 137 (3): 358–366. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000258.
Hsiao, P. C., D. E. Lehman, and C. W. Roeder. 2013. “A model to simulate special concentrically braced frames beyond brace fracture.” Earthquake Eng. Struct. Dyn. 42 (2): 183–200. https://doi.org/10.1002/eqe.2202.
Ibarra, L. F., R. A. Medina, and H. Krawinkler. 2005. “Hysteretic models that incorporate strength and stiffness deterioration.” Earthquake Eng. Struct. Dyn. 34 (12): 1489–1511. https://doi.org/10.1002/eqe.495.
Karamanci, E. 2013. “Collapse assessment and performance-based evaluation techniques for concentrically braced frames designed in seismic regions.” M.S. thesis, Dept. of Civil Engineering and Applied Mechanics, McGill Univ.
Karamanci, E., and D. G. Lignos. 2014. “Computational approach for collapse assessment of concentrically braced frames in seismic regions.” J. Struct. Eng. 140 (8): A4014019. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001011.
Lignos, D. G., and H. Krawinkler. 2009. Sidesway collapse of deteriorating structural systems under seismic excitations. Stanford, CA: John A. Blume Earthquake Engineering Center, Stanford Univ.
Liu, J., and A. Astaneh-Asl. 2000. “Cyclic testing of simple connections including effects of slab.” J. Struct. Eng. 126 (1): 32–39. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:1(32).
Liu, J., and A. Astaneh-Asl. 2004. “Moment-rotation parameters for composite shear tab connections.” J. Struct. Eng. 130 (9): 1371–1380. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:9(1371).
McGuire, R. K., W. J. Silva, and C. J. Constantino. 2001. Technical basis for revision of regulatory guidance on design ground motions. Rockville, MD: US Nuclear Regulatory Commission.
McKenna, F. 1997. “Object oriented finite element programming frameworks for analysis, algorithms and parallel computing.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of California at Berkeley.
Nakashima, M., K. Inoue, and M. Tada. 1998. “Classification of damage to steel buildings observed in the 1995 Hyogoken-Nanbu earthquake.” Eng. Struct. 20 (4): 271–281. https://doi.org/10.1016/S0141-0296(97)00019-9.
PEER/ATC (Pacific Earthquake Engineering Research Center and Applied Technology Council). 2010. Modeling and acceptance criteria for seismic design and analysis of tall buildings. Redwood City, CA: Applied Technology Council.
Rai, D. C., and S. C. Goel. 2003. “Seismic evaluation and upgrading of chevron braced frames.” J. Constr. Steel Res. 59 (8): 971–994. https://doi.org/10.1016/S0143-974X(03)00006-3.
Saatcioglu, M., D. Palermo, A. Ghobarah, D. Mitchell, R. Simpson, P. Adebar, R. Tremblay, C. Ventura, and H. Hong. 2013. “Performance of reinforced concrete buildings during the 27 February 2010 Maule (Chile) earthquake.” Can. J. Civ. Eng. 40 (8): 693–710. https://doi.org/10.1139/cjce-2012-0243.
Sen, A. D., C. W. Roeder, J. W. Berman, D. E. Lehman, C. H. Li, A. C. Wu, and K. C. Tsai. 2016. “Experimental investigation of chevron concentrically braced frames with yielding beams.” J. Struct. Eng. 142 (12): 04016123. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001597.
Sizemore, J. 2017. “Inelastic behavior and seismic collapse prevention performance of low-ductility steel braced frames.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana-Champaign.
Sizemore, J., L. Fahnestock, E. Hines, and C. Bradley. 2017. “Parametric study of low-ductility concentrically-braced frames under cyclic static loading.” J. Struct. Eng. 143 (6): 04017032. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001761.
Stoakes, C. 2012. “Beam-column connection flexural behavior and seismic collapse performance of concentrically braced frames.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana-Champaign.
Stoakes, C. D., and L. A. Fahnestock. 2011. “Cyclic flexural testing of concentrically braced frame beam-column connections.” J. Struct. Eng. 137 (7): 739–747. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000326.
Stoakes, C. D., and L. A. Fahnestock. 2012. “Cyclic flexural analysis and behavior of beam-column connections with gusset plates.” J. Constr. Steel Res. 72 (May): 227–239. https://doi.org/10.1016/j.jcsr.2011.12.008.
Tremblay, R., A. Filiatrault, M. Bruneau, M. Nakashima, H. G. Prion, and R. DeVall. 1996. “Seismic design of steel buildings: Lessons from the 1995 Hyogo-ken Nanbu earthquake.” Can. J. Civ. Eng. 23 (3): 727–756. https://doi.org/10.1139/l96-885.
Tremblay, R., A. Filiatrault, P. Timler, and M. Bruneau. 1995. “Performance of steel structures during the 1994 Northridge earthquake.” Can. J. Civ. Eng. 22 (2): 338–360. https://doi.org/10.1139/l95-046.
Tremblay, R., D. Mitchell, and R. Tinawi. 2013. “Damage to industrial structures due to the 27 February 2010 Chile earthquake.” Can. J. Civ. Eng. 40 (8): 735–749. https://doi.org/10.1139/cjce-2012-0197.
Uriz, P. 2005. “Towards earthquake resistant design of concentrically braced steel structures.” Ph.D. dissertation, Dept. of Civil and Environmental Engineering, Univ. of California.
Zareian, F., and R. A. Medina. 2010. “A practical method for proper modeling of structural damping in inelastic plane structural systems.” Comput. Struct. 88 (1): 45–53. https://doi.org/10.1016/j.compstruc.2009.08.001.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Jan 10, 2018
Accepted: Aug 30, 2018
Published online: Feb 15, 2019
Published in print: Apr 1, 2019
Discussion open until: Jul 15, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.