Multiobjective Aerodynamic Optimization of Tall Building Openings for Wind-Induced Load Reduction
Publication: Journal of Structural Engineering
Volume 144, Issue 10
Abstract
The dependency of wind forces and responses on the outer shape of tall buildings provides a unique opportunity to reduce wind effects through the aerodynamic optimization of the outer shape. The current study presents a multiobjective aerodynamic optimization procedure (AOP) by introducing horizontal openings to reduce wind load. The adopted method joins an optimization algorithm, large eddy simulation (LES), and an artificial neural network (ANN) surrogate model. The base building geometry is the Commonwealth Advisory Aeronautical Research Council (CAARC) building. The present optimization process is carried out by introducing three openings along the height of the building. However, the adopted method is useful for any shape modifications. In all cases, opening volumes are maintained at 10% of the total building volume to enable a simple comparative performance assessment. The objective of the optimization process is to identify the optimal aspect ratio and distances between the openings that produce the best aerodynamic performance. Three optimization problems are presented. The first two follow single-objective optimization to reduce the peak base moment coefficients about the - and -directions, respectively. Reductions of 47% and 42% are achieved for the moments about the - and -directions, respectively. The third optimization is a multiobjective optimization problem, which aims to simultaneously reduce the two base moments.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the financial support from the National Research Council of Canada (NSERC), Canada Research Chair (for the second author), and Ontario Center of Excellence and SOSCIP Talent Edge Postdoctoral Fellowship (for the first author). The authors are grateful for access to SHARCNET and SOSCIP (high-performance computing centers) and support received from their excellent technical support team.
References
Aboshosha, H., A. Elshaer, G. T. Bitsuamlak, and A. El Damatty. 2015. “Consistent inflow turbulence generator for LES evaluation of wind-induced responses for tall buildings.” J. Wind Eng. Ind. Aerodyn. 142: 198–216. https://doi.org/10.1016/j.jweia.2015.04.004.
Ansary, A. M., A. El Damatty, and A. O. Nassef. 2011. “Optimum shape and design of cooling towers.” World Acad. Sci. Eng. Technol. 5 (12): 655–664. https://doi.org/10.1999/1307-6892/6558.
Bernardini, E., S. M. J. Spence, D. Wei, and A. Kareem. 2015. “Aerodynamic shape optimization of civil structures: A CFD-enabled kriging-based approach.” J. Wind Eng. Ind. Aerodyn. 144: 154–164. https://doi.org/10.1016/j.jweia.2015.03.011.
Bitsuamlak, G., T. Stathopoulos, and C. Bedard. 2006. “Effects of upstream two-dimensional hills on design wind loads: A computational approach.” Wind Struct. 9 (1): 37–58. https://doi.org/10.12989/was.2006.9.1.037.
Braun, A. L., and A. M. Awruch. 2009. “Aerodynamic and aeroelastic analyses on the CAARC standard tall building model using numerical simulation.” Comput. Struct. 87 (9): 564–581. https://doi.org/10.1016/j.compstruc.2009.02.002.
Carassale, L., A. Freda, and M. Marrè-Brunenghi. 2014. “Experimental investigation on the aerodynamic behavior of square cylinders with rounded corners.” J. Fluids Struct. 44: 195–204. https://doi.org/10.1016/j.jfluidstructs.2013.10.010.
Dagnew, A., and G. T. Bitsuamlak. 2013. “Computational evaluation of wind loads on buildings: A review.” Wind Struct. 16 (6): 629–660. https://doi.org/10.12989/was.2013.16.6.629.
Dagnew, A., and G. T. Bitsuamlak 2014. “Computational evaluation of wind loads on a standard tall building using LES.” Wind Struct. 18 (5): 567–598. https://doi.org/10.12989/was.2014.18.5.567.
Davenport, A. G. 1988. “The response of supertall buildings to wind. Second century of the skyscraper.” In Council on tall buildings and the urban habitat. New York: Van Nostrand Reinhold.
Davis, L. 1991. Handbook of genetic algorithms. New York: Van Nostrand Reinhold.
Dutton, R., and N. Isyumov. 1990. “Reduction of tall building motion by aerodynamic treatments.” J. Wind Eng. Ind. Aerodyn. 36: 739–747. https://doi.org/10.1016/0167-6105(90)90071-J.
Elshaer, A., H. Aboshosha, G. Bitsuamlak, A. El Damatty, and A. Dagnew. 2016a. “LES evaluation of wind-induced responses for an isolated and a surrounded tall building.” Eng. Struct. 115: 179–195. https://doi.org/10.1016/j.engstruct.2016.02.026.
Elshaer, A., G. Bitsuamlak, and A. El Damatty. 2015a. “Aerodynamic shape optimization for corners of tall buildings using CFD.” In Proc., 14th Int. Conf. on Wind Engineering. Atsugi, Kanagawa, Japan: International Association for Wind Engineering.
Elshaer, A., G. Bitsuamlak, and A. El Damatty. 2015b. “Vibration control of tall buildings using aerodynamic optimization.” In Proc., 25th Canadian Congress of Applied Mechanics. Victoria, British Columbia, Canada: Canadian Congress of Applied Mechanics.
Elshaer, A., G. Bitsuamlak, and A. El Damatty. 2016b. “Aerodynamic shape optimization of tall buildings using twisting and corner modifications.” In Proc., 8th Int. Colloquium on Bluff Body Aerodynamics and Applications. Atsugi, Kanagawa, Japan: International Association for Wind Engineering.
Elshaer, A., G. Bitsuamlak, and A. El Damatty. 2017. “Enhancing wind performance of tall buildings using corner aerodynamic optimization.” Eng. Struct. 136: 133–148. https://doi.org/10.1016/j.engstruct.2017.01.019.
ESDU (Engineering Sciences Data Unit). 2001. Characteristics of atmospheric turbulence near the ground. Part II: Single point data for strong winds. London: IHS Markit.
Franke, J. 2007. COST. Best practice guideline for the CFD simulation of flows in the urban environment. Edited by J. Franke, A. Hellsten, H. Schlünzen, and B. Carissimo. Hamburg, Germany: Univ. of Hamburg.
Franke, J., A. Hellsten, H. Schlünzen, and B. Carissimo. 2007. Best practice guideline for the CFD simulation of flows in the urban environment. COST action 732: Quality assurance and improvement of microscale meteorological models. Hamburg, Germany: Univ. of Hamburg, Meteorological Institute, Centre for Marine and Atmospheric Sciences.
Germano, M., U. Piomelli, P. Moin, and W. H. Cabot. 1991. “A dynamic subgrid-scale eddy viscosity model.” Phys. Fluids A 3 (7): 1760–1765. https://doi.org/10.1063/1.857955.
Goolberg, D. E. 1989. Genetic algorithms in search, optimization, and machine learning, 102. Boston: Addison Wesley.
Gu, M. Ã., and Y. Quan. 2004. “Across-wind loads of typical tall buildings.” J. Wind Eng. Ind. Aerodyn. 92 (13): 1147–1165. https://doi.org/10.1016/j.jweia.2004.06.004.
Huang, S. H., Q. S. Li, and J. R. Wu. 2010a. “A general inflow turbulence generator for large eddy simulation.” J. Wind Eng. Ind. Aerodyn. 98 (10): 600–617. https://doi.org/10.1016/j.jweia.2010.06.002.
Huang, S. H., Q. S. Li, and J. R. Wu. 2010b. “Large eddy simulation of wind effects on a super-tall building.” Wind Struct. 13 (6): 557–580. https://doi.org/10.12989/was.2010.13.6.557.
Kareem, A., S. M. Spence, E. Bernardini, S. Bobby, and D. Wei. 2013. “Using computational fluid dynamics to optimize tall building design.” Council of Tall Buildings and Urban Habitat J. 38–43.
Kawai, H. 1998. “Effect of corner modifications on aeroelastic instabilities of tall buildings.” J. Wind Eng. Ind. Aerodyn. 74: 719–729. https://doi.org/10.1016/S0167-6105(98)00065-8.
Kwok, K. C. S., and P. A. Bailey. 2006. “Aerodynamic devices for tall buildings and structures.” J. Eng. Mech. 113 (3): 349–365. https://doi.org/10.1061/(ASCE)0733-9399(1987)113:3(349).
Kwok, K. C. S., M. D. Burton, and A. K. Abdelrazaq. 2015. “Wind-induced motion of tall buildings.” Int. J. High-Rise Build. 4 (1): 1–8. https://doi.org/10.1061/9780784413852.
Kwok, K. C. S., P. A. Wilhelm, and B. G. Wilkie. 1988. “Effect of edge configuration on wind-induced response of tall buildings.” Eng. Struct. 10 (2): 135–140. https://doi.org/10.1016/0141-0296(88)90039-9.
Melbourne, W. H. 1980. “Comparison of measurements on the CAARC standard tall building model in simulated model wind flows.” J. Wind Eng. Ind. Aerodyn. 6 (1–2): 73–88. https://doi.org/10.1016/0167-6105(80)90023-9.
Merrick, R., and G. Bitsuamlak. 2009. “Shape effects on the wind-induced response of high-rise buildings.” J. Wind Eng. 6 (2): 1–18.
Michalewicz, Z., and D. B. Fogel. 2013. How to solve it: Modern heuristics. Berlin: Springer Science & Business Media.
Miyashita, K., J. Katagiri, O. Nakamura, T. Ohkuma, Y. Tamura, M. Itoh, and T. Mimachi. 1993. “Wind-induced response of high-rise buildings effects of corner cuts or openings in square buildings.” J. Wind Eng. Ind. Aerodyn. 50: 319–328. https://doi.org/10.1016/0167-6105(93)90087-5.
Murakami, S. 1998. “Overview of turbulence models applied in CWE-1997.” J. Wind Eng. Ind. Aerodyn. 74: 1–24. https://doi.org/10.1016/S0167-6105(98)00004-X.
Nozawa, K., and T. Tamura. 2002. “Large eddy simulation of the flow around a low-rise building immersed in a rough-wall turbulent boundary layer.” J. Wind Eng. Ind. Aerodyn. 90 (10): 1151–1162. https://doi.org/10.1016/S0167-6105(02)00228-3.
Simiu, E., and R. H. Scanlan. 1996. Wind effects on structures. New York: Wiley.
Smagorinsky, J. 1963. “General circulation experiments with the primitive equations: I. The basic experiment.” Mon. Weather Rev. 91 (3): 99–164. https://doi.org/10.1175/1520-0493(1963)091%3C0099:GCEWTP%3E2.3.CO;2.
Statistics Canada. 2011. “Census of population.” Accessed February 4, 2011. http://www.statcan.gc.ca/tables-tableaux/sum-som/l01/cst01/demo62a-eng.htm.
Tamura, T., and T. Miyagi. 1999. “The effect of turbulence on aerodynamic forces on a square cylinder with various corner shapes.” J. Wind Eng. Ind. Aerodyn. 83 (1–3): 135–145. https://doi.org/10.1016/S0167-6105(99)00067-7.
Tamura, T., T. Miyagi, and T. Kitagishi. 1998. “Numerical prediction of unsteady pressures on a square cylinder with various corner shapes.” J. Wind Eng. Ind. Aerodyn. 76: 531–542. https://doi.org/10.1016/S0167-6105(98)00048-8.
Tanaka, H., Y. Tamura, K. Ohtake, M. Nakai, and Y. Chul. 2012. “Journal of Wind Engineering experimental investigation of aerodynamic forces and wind pressures acting on tall buildings with various unconventional configurations.” J. Wind Eng. Ind. Aerodyn. 107: 179–191. https://doi.org/10.1016/j.jweia.2012.04.014.
Tominaga, Y., A. Mochida, R. Yoshie, H. Kataoka, T. Nozu, M. Yoshikawa, and T. Shirasawa. 2008. “AIJ guidelines for practical applications of CFD to pedestrian wind environment around buildings.” J. Wind Eng. Ind. Aerodyn. 96 (10): 1749–1761. https://doi.org/10.1016/j.jweia.2008.02.058.
Tse, K. T., P. A. Hitchcock, K. C. S. Kwok, S. Thepmongkorn, and C. M. Chan. 2009. “Economic perspectives of aerodynamic treatments of square tall buildings.” J. Wind Eng. Ind. Aerodyn. 97 (9–10): 455–467. https://doi.org/10.1016/j.jweia.2009.07.005.
Wardlaw, R. L., and G. F. Moss. 1970. A standard tall building model for the comparison of simulated natural winds in wind tunnels. London: Commonwealth Advisory Aeronautical Research Council Rep.
Xie, J. 2014. “Aerodynamic optimization of super-tall buildings and its effectiveness assessment.” J. Wind Eng. Ind. Aerodyn. 130: 88–98. https://doi.org/10.1016/j.jweia.2014.04.004.
Zhou, L., and F. Haghighat. 2009. “Optimization of ventilation system design and operation in office environment. Part I: Methodology.” Build. Environ. 44 (4): 651–656. https://doi.org/10.1016/j.buildenv.2008.05.009.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 17, 2017
Accepted: May 8, 2018
Published online: Aug 14, 2018
Published in print: Oct 1, 2018
Discussion open until: Jan 14, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.