Development and Experimental Validation of the Direct Strength Method for Cold-Formed Steel Beam-Columns
Publication: Journal of Structural Engineering
Volume 144, Issue 10
Abstract
The direct strength method of cold-formed steel member design uses local, distortional, and global cross-section elastic buckling analysis with empirically derived direct expressions to predict member strength. The direct strength method is an accepted design method in national design specifications and enables a unified, robust, and flexible design approach. However, for beam-columns the direct strength method in current design specifications uses simplified linear interaction expressions based on combining the pure axial and bending elastic buckling and strength response. Today, local, distortional, and global elastic buckling under any combination of axial load and bending moments may be readily found using elastic buckling analysis tools such as the finite strip method. Thus, stability may be assessed under the actual combined actions, but new direct strength method expressions are needed to utilize this explicit stability information in determining beam-column strength. In this paper, new strength expressions for each limit state are developed. In addition, the results of beam-column tests performed by the authors and those available in the literature are used to validate the performance of the new proposed direct strength method for beam-columns. The development of the direct strength method for beam-columns has the potential to provide a more mechanically sound solution to the strength of cold-formed steel beam-columns, eliminate excessive conservativeness, and at the same time encourage the next generation of optimized, high-strength cold-formed steel shapes.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the American Iron and Steel Institute and the Metal Building Manufacturers Association for funding this study. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the views of the sponsors or other participants.
References
AISI (American Iron and Steel Institute). 2012. North american standard for cold-formed steel framing—General provisions. AISI S200-12. Washington, DC: AISI.
AISI (American Iron and Steel Institute). 2016. North American specification for the design of cold-formed steel structural members. Washington, DC: AISI.
Albermani, F., and S. Kitipornchai. 1990. “Elasto-plastic large deformation analysis of thin-walled structures.” Eng. Struct. 12 (1): 28–36. https://doi.org/10.1016/0141-0296(90)90035-Q.
Baptista, A. M. 2012a. “Analytical evaluation of the elastic and plastic resistances of double symmetric rectangular hollow sections under axial force and biaxial bending.” Int. J. Non Linear Mech. 47 (9): 1033–1044. https://doi.org/10.1016/j.ijnonlinmec.2012.06.008.
Baptista, A. M. 2012b. “Resistance of steel I-sections under axial force and biaxial bending.” J. Constr. Steel Res. 72: 1–11. https://doi.org/10.1016/j.jcsr.2011.07.013.
Baptista, A. M., and J.-P. Muzeau. 2006. “Analytical formulation of the elastic-plastic behaviour of bi-symmetrical steel shapes.” J. Constr. Steel Res. 62 (9): 872–884. https://doi.org/10.1016/j.jcsr.2006.01.001.
Baptista, A. M., and J.-P. Muzeau. 2008. “Analytical formulation for the deformations of I-shapes and RHS at the plastic strain ultimate limit state.” J. Constr. Steel Res. 64 (10): 1165–1177. https://doi.org/10.1016/j.jcsr.2007.09.012.
Camotim, D., and P. B. Dinis. 2011. “Coupled instabilities with distortional buckling in cold-formed steel lipped channel columns.” Thin Walled Struct. 49 (5): 562–575. https://doi.org/10.1016/j.tws.2010.09.003.
Chan, S. L., and S. Kitipornchai. 1986. Geometric nonlinear analysis of asymmetric thin-walled members. St. Lucia, Australia: Dept. of Civil Engineering, Univ. of Queensland.
Charalampakis, A. E., and V. K. Koumousis. 2008. “Ultimate strength analysis of composite sections under biaxial bending and axial load.” Adv. Eng. Software 39 (11): 923–936. https://doi.org/10.1016/j.advengsoft.2008.01.007.
Dinis, P. B., D. Camotim, E. M. Batista, and E. Santos. 2011. “Local/distortional/global mode coupling in fixed lipped channel columns: Behaviour and strength.” Adv. Steel Constr. 7 (1): 113–130. https://doi.org/10.1590/S1679-78252014000800005.
Duong, H. M., and G. J. Hancock. 2004. “Recent developments in the direct strength design of thin-walled members.” In Thin-walled structures: Recent advances and future trends in thin-walled structures technology, edited by J. Loughlan. Bath, England: Canopus Publishing.
Hancock, G. J. 2003. “Cold-formed steel structures.” J. Constr. Steel Res. 59 (4): 473–487. https://doi.org/10.1016/S0143-974X(02)00103-7.
Kalyanaraman, V., and P. Jayabalan. 1994. “Local buckling of stiffened and unstiffened elements under nonuniform compression.” In Proc., Int. Specialty Conf. on Cold-Formed Steel Structures: Recent Research and Developments in Cold-Formed Steel Design and Construction, 1–9. Rolla, MO: Center for Cold-Formed Steel Structure.
Kitipornchai, S., K. Zhu, Y. Xiang, and F. G. Al-Bermani. 1991. “Single-equation yield surfaces for monosymmetric and asymmetric sections.” Eng. Struct. 13 (4): 366–370. https://doi.org/10.1016/0141-0296(91)90023-6.
Li, Z., M. T. Hanna, S. Ádány, and B. W. Schafer. 2011. “Impact of basis, orthogonalization, and normalization on the constrained finite strip method for stability solutions of open thin-walled members.” Thin Walled Struct. 49 (9): 1108–1122. https://doi.org/10.1016/j.tws.2011.04.003.
Li, Z., and B. W. Schafer. 2010. “Application of the finite strip method in cold-formed steel member design.” J. Constr. Steel Res. 66 (8–9): 971–980. https://doi.org/10.1016/j.jcsr.2010.04.001.
Loh, T. S. 1982a. Combined axial load and bending in cold-formed steel members. Ithaca, NY: American Iron and Steel Institute.
Loh, T. S. 1982b. “Combined axial load and bending in cold-formed steel members.” M.S. thesis, Dept. of Civil and Environmental Engineering, Cornell Univ.
Loh, T. S. 1985. “Combined axial load and bending in cold-formed steel members.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Cornell Univ.
Loughlan, L. 1979. “Mode interaction in lipped channel column under concentric or eccentric loading.” Ph.D. thesis, Dept. of Mechanics of Materials, Univ. of Strathclyde.
Macdonald, M., M. A. Heiyantuduwa, and J. Rhodes. 2008. “Recent developments in the design of cold-formed steel members and structures.” Thin Walled Struct. 46 (7–9): 1047–1053. https://doi.org/10.1016/j.tws.2008.01.039.
Miller, T. H., and T. Peköz. 1994. “Load-eccentricity effects on cold-formed steel lipped-channel columns.” J. Struct. Eng. 120 (3): 805–823. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:3(805).
Mulligan, G. P. 1983. The influence of local buckling on the structural behavior of singly-symmetric cold-formed steel columns. Rolla, MO: Center for Cold-Formed Steel Structures Library. 117. https://scholarsmine.mst.edu/ccfss-library/117.
Papanikolaou, V. K. 2012. “Analysis of arbitrary composite sections in biaxial bending and axial load.” Comput. Struct. 98–99 (May): 33–54. https://doi.org/10.1016/j.compstruc.2012.02.004.
Peköz, T. 1967. “Torsional-flexural buckling of thin-walled open sections under eccentric axial loading.” Ph.D. thesis, Cornell Univ.
Peköz, T. 1986. “Development of a unified approach to the design of cold-formed steel members.” In Proc., 8th Int. Specialty Conf. on Cold-Formed Steel Structures, 77–84. Rolla, MO: Center for Cold-Formed Steel Structure.
Peterman, K. 2012. “Experiments on the stability of sheathed cold-formed steel studs under axial load and bending.” M.S. thesis, Dept. of Civil Engineering, Johns Hopkins Univ.
Rondal, J. 2000. “Cold formed steel members and structures: General report.” J. Constr. Steel Res. 55 (1–3): 155–158. https://doi.org/10.1016/S0143-974X(99)00083-8.
Sarawit, A. 2006. CUTWP thin-walled section properties. Ithaca, NY: Dept. of Civil and Environmental Engineering, Cornell Univ.
Schafer, B. W. 2002. “Local, distortional, and Euler buckling of thin-walled columns.” J. Struct. Eng. 128 (3): 289–299. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:3(289).
Schafer, B. W. 2003. “Advances in direct strength design of thin-walled members.” In Proc., Advances in Structures (ASSCCA’03), edited by G. J. Hancock, M. A. Bradford, T. J. Wilkinson, B. Uy, and K. J. R. Rasmussen, 333–338. Sydney, Australia: Balkema Publishers.
Schafer, B. W. 2006. Direct strength method (DSM) design guide. Ithaca, NY: American Iron and Steel Institute.
Schafer, B. W. 2008. “Review: The direct strength method of cold-formed steel member design.” J. Constr. Steel Res. 64 (7–8): 766–778. https://doi.org/10.1016/j.jcsr.2008.01.022.
Schafer, B. W., and S. Adany. 2006. “Buckling analysis of cold-formed steel members using CUFSM: Conventional and constrained finite strip methods.” In Proc., 18th Int. Specialty Conf. on Cold-Formed Steel Structure. Rolla, MO: Univ. of Missouri–Rolla.
Sfakianakis, M. G. 2002. “Biaxial bending with axial force of reinforced, composite and repaired concrete sections of arbitrary shape by fiber model and computer graphics.” Adv. Eng. Software 33 (4): 227–242. https://doi.org/10.1016/S0965-9978(02)00002-9.
Shifferaw, Y. 2010. “Section capacity of cold-formed steel members by the direct strength method.” Ph.D. thesis, Dept. of Civil Engineering, Johns Hopkins Univ.
Shifferaw, Y., and B. W. Schafer. 2012. “Inelastic bending capacity of cold-formed steel members.” J. Struct. Eng. 138 (4): 468–480. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000469.
Standards Australia. 2005. Cold-formed steel structures. NZS 4600. Sydney, Australia: Standards Australia.
Torabian, S., D. C. Fratamico, and B. W. Schafer. 2016a. “Experimental response of cold-formed steel Zee-section beam-columns.” Thin Walled Struct. 98 (Jan): 496–517. https://doi.org/10.1016/j.tws.2015.10.016.
Torabian, S., B. Zheng, and B. W. Schafer. 2014a. Direct strength prediction of cold-formed steel beam-columns. Ithaca, NY: American Iron and Steel Institute.
Torabian, S., B. Zheng, and B. W. Schafer. 2014b. “Experimental study and modeling of cold-formed steel lipped channel stub beam-columns.” In Proc., Annual Stability Conf. Structural Stability Research Council, SSRC 2014. Toronto, ON, Canada: SSRC.
Torabian, S., B. Zheng, and B. W. Schafer. 2015. “Experimental response of cold-formed steel lipped channel beam-columns.” Thin Walled Struct. 89 (Apr): 152–168. https://doi.org/10.1016/j.tws.2014.12.003.
Torabian, S., B. Zheng, Y. Shifferaw, and B. W. Schafer. 2016b. Direct strength prediction of cold-formed steel beam-columns. Ithaca, NY: American Iron and Steel Institute.
Yap, D. C. Y., and G. J. Hancock. 2011. “Experimental study of high-strength cold-formed stiffened-web C-sections in compression.” J. Struct. Eng. 137 (2): 162–172. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000271.
Yap, D. C. Y., and G. J. Hancock. 2008. “Experimental study of complex high-strength cold-formed cross-shaped steel section.” J. Struct. Eng. 134 (8): 1322–1333. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:8(1322).
Young, B. 2008. “Research on cold-formed steel columns.” Thin Walled Struct. 46 (7–9): 731–740. https://doi.org/10.1016/j.tws.2008.01.025.
Yu, C., and B. Schafer. 2006. “Distortional buckling tests on cold-formed steel beams.” J. Struct. Eng. 132 (4): 515–528. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:4(515).
Yu, C., and B. W. Schafer. 2003. “Local buckling tests on cold-formed steel beams.” J. Struct. Eng. 129 (12): 1596–1606. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:12(1596).
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 144 • Issue 10 • October 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jan 29, 2017
Accepted: Feb 9, 2018
Published online: Jul 14, 2018
Published in print: Oct 1, 2018
Discussion open until: Dec 14, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.