Maximum and Residual Flexural Crack Width Estimation in Reinforced Concrete Frame Members under Seismic Excitation
Publication: Journal of Structural Engineering
Volume 144, Issue 8
Abstract
During strong seismic excitations, reinforced concrete (RC) frame members experience several cycles of nonlinear response that may result in large cracks. At the end of the excitation, the residual member crack widths are reduced compared to their maximum transient crack width. Interpretation of maximum and residual crack widths in RC frame members under cyclic stress reversal is very important for condition assessment of the damaged members after an earthquake. Similarly, accurate prediction of crack widths in RC frame members is very important for the performance assessment of buildings under postulated seismic excitations. In this paper, new expressions to estimate maximum flexural crack width and residual crack width in RC frame members under service loads, as well as cyclic load reversals, have been presented. The expressions are valid for both linear and nonlinear response ranges of the frame members. The expression for the maximum crack width accounts for alteration from flexural to shear-dominating damage modes caused by an increase in axial load. The residual crack width is found to depend on maximum crack width and maximum curvature ductility demand. It is not significantly affected by stress reversal imposed by cyclic loads. The proposed expressions are found to match well with experimental observations in the published literature.
Get full access to this article
View all available purchase options and get full access to this article.
References
ACI (American Concrete Institute). 2001. Control of cracking in concrete structures. ACI-224. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2008. Building code requirement for structural concrete and commentary. ACI-318. Farmington Hills, MI: ACI.
Allam, S. M., M. S. Shoukry, G. E. Rashad, and A. S. Hassan. 2012. “Crack width evaluation for flexural RC members.” Alexandria Eng. J. 51 (3): 211–220. https://doi.org/10.1016/j.aej.2012.05.001.
Anagnostopoulos, S., and M. Moretti. 2008. “Post-earthquake emergency assessment of building damage, safety and usability—Part 1: Technical issues.” Soil Dyn. Earthquake Eng. 28 (3): 223–232. https://doi.org/10.1016/j.soildyn.2006.05.007.
ASCE. 2006. Seismic rehabilitation of existing buildings. ASCE-41. Reston, VA: ASCE.
ATC (Applied Technology Council). 1992. Building code requirement for structural concrete and commentary. ATC-24. Redwood City, CA: ATC.
Balazs, G. L. 1993. “Cracking analysis based on slip and bond stresses.” ACI Mater. J. 90 (4): 340–348. https://doi.org/10.14359/3890.
Bazant, Z. P., and B. H. Oh. 1983. “Spacing of cracks in reinforced concrete.” J. Struct. Eng. 109 (9): 2066–2085. https://doi.org/10.1061/(ASCE)0733-9445(1983)109:9(2066).
Beeby, A. W. 1979. “The prediction of crack widths in hardened concrete.” Struct. Eng. 57 (1): 9–17.
Borosnyoi, A., and G. L. Balazs. 2005. “Models for flexural cracking in concrete: The state of the art.” Struct. Concr. 6 (2): 53–62. https://doi.org/10.1680/stco.2005.6.2.53.
British Standard Institution. 1998. Structural use of concrete. Part 2: Code of practice for special circumstances. BS-8110. London, UK: British Standard Institution.
CEN (European Committee for Standardization). 1991. Design of concrete structures. Part 1: General rules and rules for buildings. Eurocode-2. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2005. Design of concrete structures. Part 1: General rules and rules for buildings. Eurocode-8. Brussels, Belgium: CEN.
Chen, L., X. Lu, H. Jiang, and J. Zheng. 2009. “Experimental investigation of damage behavior of RC frame members including non-seismically designed columns.” Earthquake Eng. Eng. Vibr. 8 (2): 301–311. https://doi.org/10.1007/s11803-009-9018-3.
Dazio, A., K. Beyer, and H. Bachmann. 2009. “Quasi-static cyclic tests and plastic hinge analysis of RC structural walls.” Eng. Struct. 31 (7): 1556–1571. https://doi.org/10.1016/j.engstruct.2009.02.018.
Edwards, A. D., and A. Picard. 1972. “Theory of cracking in concrete members.” J. Struct. Eng. 98 (12): 2687–2700.
Elwood, K. J., and M. O. Eberhard. 2009. “Effective stiffness of reinforced concrete columns.” ACI Struct. J. 106 (4): 476–484.
FEMA (Federal Emergency Management Agency). 2000. Prestandard and commentary for the seismic rehabilitation of buildings. FEMA-356. Washington, DC: FEMA.
Frosch, R. J. 1999. “Another look at cracking and crack control in reinforced concrete.” ACI Struct. J. 96 (3): 437–442.
Gergely, P., and L. A. Lutz. 1968. “Maximum crack-width in reinforced concrete flexural members: Causes, mechanism, and control of cracking in concrete.” Spec. Publ. 20: 87–117.
Ministry of Housing. 2007. The Egyptian code for design and construction of reinforced concrete structures. ECP-203. Cairo, Egypt: Ministry of Housing.
Oh, B. H., and Y. J. Kang. 1987. “New formulas for maximum crack width and crack spacing in reinforced concrete flexural members.” ACI Struct. J. 84 (2): 103–112.
Oh, B. H., and S. H. Kim. 2007a. “Advanced crack width analysis of reinforced concrete beams under repeated loads.” J. Struct. Eng. 133 (3): 411–420. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:3(411).
Oh, B. H., and S. H. Kim. 2007b. “Realistic models for local bond stress-slip of reinforced concrete under repeated loading.” J. Struct. Eng. 133 (2): 216–224. https://doi.org/10.1061/(ASCE)0733-9445(2007)133:2(216).
Ohkubo, M. 1991. Current Japanese system on seismic capacity and retrofit techniques for existing reinforced concrete buildings and post-earthquake damage inspection and restoration techniques. San Diego, CA: Dept. of Applied Mechanics and Engineering Sciences, Univ. of California.
Park, Y. J., A. M. Reinhorn, and S. K. Kunnath. 1987. IDARC: Inelastic damage analysis of RC frame-shear wall structures. Buffalo, NY: State Univ. of New York.
Penelis, G. G., and A. J. Kappos. 1997. Earthquake resistant concrete structures. Oxon, UK: Taylor & Francis.
Priestley, M. J. N., G. M. Calvi, and M. J. Kowalsky. 2007. Displacement-based seismic design of structures. Pavia, Italy: IUSS Press.
Rai, D. 2001. “Slow cyclic testing for evaluation of seismic performance of structural components.” J. Earthquake Technol. 38 (1): 31–35.
Reinhorn, A. M., H. Roh, M. Sivaselvan, S. K. Kunnath, R. E. Valles, A. Madan, C. Li, R. Lobo, and Y. Park. 2007. IDARC 2D Version 7.0: A program for the inelastic damage analysis of buildings. Buffalo, NY: Univ. of Buffalo.
Sezen, H., and J. P. Moehle. 2003. “Bond-slip behavior of reinforced concrete members.” In Proc., Fib Symp. on Concrete Structures in Seismic Regions 2003. Athens, Greece: Technical Chamber of Greece.
Shiradhonkar, S. R. 2016. “Seismic damage categorisation and damage index for reinforced concrete buildings.” Ph.D. thesis, Indian Institute of Technology Bombay.
Sinha, R., and A. Goyal. 2004. A national policy of seismic vulnerability assessment of buildings and procedure for rapid visual screening of buildings for potential seismic vulnerability. Mumbai, India: Indian Institute of Technology Bombay.
Standards New Zealand. 2006. Concrete structures standard. NZS-3101. Wellington, New Zealand: Standards New Zealand.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 144 • Issue 8 • August 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Jun 12, 2017
Accepted: Feb 8, 2018
Published online: Jun 12, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 12, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.