Abstract
The tension-stiffening behavior of fiber-reinforced concrete is of fundamental importance for the characterization of crack widths and spacings as well as determination of the tensile response of fiber-reinforced concrete members with internal reinforcement. In this paper, a model is presented for the tension-stiffening behavior of strain-softening and strain-hardening fiber-reinforced and ultra-high-performance fiber-reinforced concrete with an allowance for the long-term creep and shrinkage effects of the concrete. Closed-form analytical solutions are derived to describe the crack spacings and load slip behavior assuming either a simplified linear ascending bond stress–slip relationship or a more realistic bond stress–slip relationship from the literature. Further, it is shown for design how the stiffness of the reinforcement can be characterized using an effective modular ratio, which can easily be incorporated into member analysis techniques to characterize the serviceability behavior of flexural members. Finally, the results are validated against a broad range of fiber-reinforced concretes of normal, high, and ultra-high strength, thus demonstrating validity for a wide range of different fiber-reinforced concretes (FRCs).
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This material is based upon work supported by the Air Force Office of Scientific Research under Award No. FA2386-16-1-4098.
References
Amin, A., S. J. Foster, and M. Watts. 2015. “Modelling the tension stiffening effect in SFR-RC.” Mag. Concr. Res. 68 (7): 339–352. https://doi.org/10.1680/macr.15.00188.
Balazs, G. L. 1993. “Cracking analysis based on slip and bond stresses.” ACI Mater. J. 90 (4): 340–348.
Barragán, B. E. 2002. “Failure and toughness of steel fiber reinforced concrete under tension and shear.” Ph.D. thesis, Universitat Politècnica de Catalunya. https://upcommons.upc.edu/handle/2117/93220?locale-attribute=en.
Bazant, Z. P. 1972. “Prediction of concrete creep effects using age-adjusted effective modulus method.” ACI J. 69 (4): 212–217.
Bischoff, P. H. 2001. “Effects of shrinkage on tension stiffening and cracking in reinforced concrete.” Can. J. Civ. Eng. 28 (3): 363–374. https://doi.org/10.1139/l00-117.
Bischoff, P. H. 2003. “Tension stiffening and cracking of steel fiber-reinforced concrete.” J. Mater. Civ. Eng. 15 (2): 174–182. https://doi.org/10.1061/(ASCE)0899-1561(2003)15:2(174).
CEB-FIP (Euro-International Committee for Concrete/International Federation for Pre-stressing). 1993. CEB-FIP model code 1990: Design code. London, UK: Thomas Telford.
CEN (European Committee for Standardization). 1992. Design of concrete structures. Part 1-1: General rules and rules for buildings. Eurocode 2. Brussel, Belgium: CEN.
Choi, C. K., and S. H. Cheung. 1996. “Tension stiffening model for planar reinforced concrete members.” Comput. Struct. 59 (1): 179–190. https://doi.org/10.1016/0045-7949(95)00146-8.
Deluce, J. R. 2011. “Cracking behaviour of steel fibre reinforced concrete containing conventional steel reinforcement.” Master’s thesis, Univ. of Toronto. https://tspace.library.utoronto.ca/handle/1807/29523.
Deluce, J. R., S. C. Lee, and F. J. Vecchio. 2014. “Crack model for steel fiber-reinforced concrete members containing conventional reinforcement.” ACI Struct. J. 111 (1): 93.
Dilger, W., and A. M. Neville. 1971. “Method of creep analysis of structural members.” Spec. Publ. 27: 349–379.
fib (International Federation for Structural Concrete). 2013. fib model code for concrete structures 2010. Lausanne, Switzerland: Ernst & Sohn.
Grünewald, S. 2004. “Performance-based design of self-compacting fibre reinforced concrete.” Ph.D. thesis, Delft Univ. of Technology. https://repository.tudelft.nl/islandora/object/uuid:07a817aa-cba1-4c93-bbed-40a5645cf0f1.
Gupta, A. K., and S. R. Maestrini. 1990. “Tension stiffening model for reinforced concrete bars.” J. Struct. Eng. 116 (3): 769–790. https://doi.org/10.1061/(ASCE)0899-1561(2006)18:6(831).
Harajli, M., B. Hamad, and K. Karam. 2002. “Bond-slip response of reinforcing bars embedded in plain and fiber concrete.” J. Mater. Civ. Eng. 14 (6): 503–511. https://doi.org/10.1061/(ASCE)0899-1561(2002)14:6(503).
Jungwirth, J., and A. Muttoni. 2004. “Structural behavior of tension members in ultra high performance concrete.” In Proc., Int. Symp. on Ultra High Performance Concrete, edited by M. Schmidt, E. Fehling, and C. Geisenhanslüke, 533–544. Kassell, Germany: Univ. of Kassell.
Kooiman, A. G. 2000. “Modelling steel fibre reinforced concrete for structural design.” Ph.D. thesis, Delft Univ. of Technology. https://repository.tudelft.nl/islandora/object/uuid:e7a12191-4484-4fc3-b4c5-e8c0d51271a0.
Lee, G. G., and S. J. Foster. 2007. Behaviour of steel fibre reinforced mortar in shear III: Variable engagement model II. UNICIV Rep. No. R-448. Sydney, Australia: Univ. of New South Wales.
Lee, S. C., J. Y. Cho, and F. J. Vecchio. 2011a. “Diverse embedment model for steel fiber-reinforced concrete in tension: Model development.” ACI Mater. J. 108 (5): 516–525.
Lee, S. C., J. Y. Cho, and F. J. Vecchio. 2011b. “Diverse embedment model for steel fiber-reinforced concrete in tension: Model verification.” ACI Mater. J. 108 (5): 526–535.
Lee, S. C., J. Y. Cho, and F. J. Vecchio. 2013. “Tension-stiffening model for steel fiber-reinforced concrete containing conventional reinforcement.” ACI Struct. J. 110 (4): 639.
Leutbecher, T., and E. Fehling. 2012. “Tensile behavior of ultra-high-performance concrete reinforced with reinforcing bars and fibers: Minimizing fiber content.” ACI Struct. J. 109 (2): 253–263.
Li, V. C., H. Stang, and H. Krenchel. 1993. “Micromechanics of crack bridging in fibre-reinforced concrete.” Mater. Struct. 26 (8): 486–494. https://doi.org/10.1007/BF02472808.
Löfgren, I., H. Stang, and J. F. Olesen. 2004. “Wedge splitting test–A test to determine fracture properties of FRC.” In Proc., Sixth RILEM Symp. on Fibre-Reinforced Concretes (FRC), 379–388. Paris, France: International Union of Laboratories and Experts in Construction Materials, Systems and Structures (RILEM).
Maeder, U., I. Lallemant-Gamboa, J. Chaignon, and J. P. Lombard. 2004. “Ceracem, a new high performance concrete: Characterisations and applications.” In Proc., Int. Symp. on Ultra High Performance Concrete, edited by M. Schmidt, E. Fehling, and C. Geisenhanslüke, 59–68. Kassell, Germany: Univ. of Kassell.
Meda, A., G. A. Plizzari, and L. Sorelli. 2004. “Uni-axial and bending test for the determination of fracture properties of fiber reinforced concrete.” In Proc., Fifth Int. Conf. on Fracture Mechanics of Concrete and Concrete Structures, edited by V. C. Li, C. K. Y. Leung, K. J. Willam, and S. L. Billington, 1163–1170. Vail, CO: International Association of Fracture Mechanics for Concrete and Concrete Structures.
Muhamad, R., M. S. Mohamed Ali, D. J. Oehlers, and M. C. Griffith. 2012. “The tension stiffening mechanism in reinforced concrete prisms.” Adv. Struct. Eng. 15 (12): 2053–2069. https://doi.org/10.1260/1369-4332.15.12.2053.
Naaman, A. E. 2007. “Tensile strain-hardening FRC composites: Historical evolution since the 1960.” In Advances in construction materials 2007, 181–202. Berlin, Germany: Springer.
Neville, A. M., W. H. Dilger, and J. J. Brooks. 1983. Creep of plain and structural concrete. London, UK: Construction Press.
Noghabai, K. 2000. “Behavior of tie elements of plain and fibrous concrete and varying cross sections.” ACI Struct. J. 97 (2): 277–284.
Oesterlee, C. 2010. “Structural response of reinforced UHPFRC and RC composite members.” Ph.D. thesis, Ecole Polytechnique Federale de Lausanne. https://infoscience.epfl.ch/record/150553?ln=en.
Ouyang, C., A. Pacios, and S. P. Shah. 1994. “Pullout of inclined fibers from cementitious matrix.” J. Eng. Mech. 120 (12): 2641–2659. https://doi.org/10.1061/(ASCE)0733-9399(1994)120:12(2641).
Pereira, E. N. B., J. A. O. Barros, A. F. Ribeiro, and A. Camões. 2004. “Post-cracking behaviour of self-compacting steel fibre reinforced concrete” In Proc., Sixth RILEM Symp. on Fibre Reinforced Concretes (FRC). Paris, France: International Union of Laboratories and Experts in Construction Materials, Systems and Structures (RILEM).
Schumacher, P. 2006. “Rotation capacity of self-compacting steel fibre reinforced concrete.” Ph.D. thesis, Delft Univ. of Technology. https://repository.tudelft.nl/islandora/object/uuid:84d1cc79-e254-4579-a1e8-65091a7ca5c9?collection=research.
Sorelli, L. 2003. “Some studies on the assessment of the fracture toughness of fiber reinforced concrete with an emphasis on hybrid fiber systems.” Ph.D. thesis, Dept. of Civil, Environmental and Architectural Engineering and Mathematics, Univ. of Brescia.
Stang, H., and T. Aare. 1992. “Evaluation of crack width in FRC with conventional reinforcement.” Cem. Concr. Compos. 14 (2): 143–154. https://doi.org/10.1016/0958-9465(92)90007-I.
Sturm, A. B., and P. Visintin. 2017. Local bond slip behaviour of steel reinforcing bars embedded in UHPFRC. Adelaide, SA: Univ. of Adelaide.
Sturm, A. B., P. Visintin, and D. J. Oehlers. 2017. “Time-dependent serviceability behavior of reinforced concrete beams: Partial interaction tension stiffening mechanics.” Struct. Concr. 19 (2): 508–523.
Tjiptobroto, P., and W. Hansen. 1993. “Tensile strain hardening and multiple cracking in high-performance cement-based composites containing discontinuous fibers.” ACI Mater. J. 90 (1): 16–25.
Visintin, P., and D. J. Oehlers. 2017. “Fundamental mechanics that govern the flexural behaviour of RC beams with fibre reinforced concrete” In Advances in structural engineering. New Delhi, India: Springer.
Visintin, P., D. J. Oehlers, and M. Haskett. 2013. “Partial-interaction time dependent behaviour of reinforced concrete beams.” Eng. Struct. 49: 408–420. https://doi.org/10.1016/j.engstruct.2012.11.025.
Visintin, P., D. J. Oehlers, and A. B. Sturm. 2016. “Mechanics solutions for deflections and cracking in concrete.” Proc. Inst. Civ. Eng. Struct. Build. 169 (12): 912–924. https://doi.org/10.1680/jstbu.16.00009.
Visintin, P., A. B. Sturm, M. S. Mohamed Ali, and D. J. Oehlers. 2018. “Blending macro- and micro-fibres to enhance the serviceability behaviour of UHPFRC.” Aust. J. Civ. Eng., in press. https://doi.org/10.1080/14488353.2018.1463608.
Visintin, P., A. B. Sturm, and D. J. Oehlers. 2017. “Long and short term serviceability behaviour of RC beams: Mechanics models for deflections and crack widths.” Struct. Concr. 19 (2): 489–507.
Wille, K., S. El-Tawil, and A. E. Naaman. 2014. “Properties of strain hardening ultra high performance fiber reinforced concrete (UHP-FRC) under direct tensile loading.” Cem. Concr. Compos. 48: 53–66. https://doi.org/10.1016/j.cemconcomp.2013.12.015.
Wu, Z., H. Yoshikawa, and T. Tanabe. 1991. “Tension stiffness model for cracked reinforced concrete.” J. Struct. Eng. 117 (3): 715–732. https://doi.org/10.1061/(ASCE)0733-9445(1991)117:3(715).
Yuguang, Y., J. C. Walraven, and J. A. Uijl. 2009. “Combined effect of fibers and steel rebars in high performance concrete.” Heron 54 (2–3): 205–224.
Zhang, T., P. Visintin, and D. J. Oehlers. 2016. “Partial-interaction tension-stiffening properties for numerical simulations.” Adv. Struct. Eng. 20 (5): 812–821. https://doi.org/10.1177/1369433216660654.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 144 • Issue 8 • August 2018
Copyright
©2018 American Society of Civil Engineers.
History
Received: Aug 1, 2017
Accepted: Feb 4, 2018
Published online: Jun 13, 2018
Published in print: Aug 1, 2018
Discussion open until: Nov 13, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.