Ironton-Russell Bridge: Application of Vibration-Based Cable Tension Estimation
Publication: Journal of Structural Engineering
Volume 144, Issue 6
Abstract
The vibration-based tension estimation method is a common approach for health assessment of cable structures. In this methodology, cable natural frequencies along with mechanical and geometrical properties of the cable were used to estimate the cable tension. In this paper, following the vibration-based tension estimation method, stay cables of new Ironton-Russell Bridge are evaluated and the results compared against the lift-off test results. It is shown that the difference between estimated tension forces and directly measured tension forces (lift-off test) is negligible. A numerical analysis is also performed to investigate the impact of errors in measuring cable natural frequencies and cable axial stiffness on estimated cable tensions.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was sponsored and supported by the Ohio Department of Transportation (ODOT). The authors gratefully acknowledge their expertise, advice, and financial support. The authors also gratefully thank VSL International Ltd. for their cooperation and providing lift-off test results.
References
ASTM. 2017. Standard specification for low-relaxation, seven-wire steel strand for prestressed concrete. ASTM A416. West Conshohocken, PA: ASTM.
Bao, Y., Z. Shi, J. L. Beck, H. Li, and T. Y. Hou. 2017. “Identification of time-varying cable tension forces based on adaptive sparse time-frequency analysis of cable vibrations.” Struct. Control Health Monit. 24 (3): e1889.
Bouaanani, N. 2006. “Numerical investigation of the modal sensitivity of suspended cables with localized damage.” J. Sound Vib. 292 (3): 1015–1030.
Casas, J. R. 1994. “A combined method for measuring cable forces: The cable-stayed Alamillo bridge, Spain.” Struct. Eng. Int. 4 (4): 235–240.
Ceballos, M. A., and C. A. Prato. 2008. “Determination of the axial force on stay cables accounting for their bending stiffness and rotational end restraints by free vibration tests.” J. Sound Vib. 317 (1): 127–141.
Chen, C.-C., W.-H. Wu, C.-Y. Liu, and G. Lai. 2017. “Diagnosis of instant and long-term damages in cable-stayed bridges based on the variation of cable forces.” Struct. Infrastruct. Eng. 14 (5): 565–579.
Cho, S., J. P. Lynch, J.-J. Lee, and C.-B. Yun. 2010. “Development of an automated wireless tension force estimation system for cable-stayed bridges.” J. Intell. Mater. Syst. Struct. 21 (3): 361–376.
Cho, S., J. Yim, S. W. Shin, H.-J. Jung, C.-B. Yun, and M. L. Wang. 2012. “Comparative field study of cable tension measurement for a cable-stayed bridge.” J. Bridge Eng. 18 (8): 748–757.
Cunha, A., E. Caetano, and R. Delgado. 2001. “Dynamic tests on large cable-stayed bridge.” J. Bridge Eng. 6 (1): 54–62.
Fang, Z., and J.-Q. Wang. 2010. “Practical formula for cable tension estimation by vibration method.” J. Bridge Eng. 17 (1): 161–164.
Feng, D., T. Scarangello, M. Q. Feng, and Q. Ye. 2017. “Cable tension force estimate using novel noncontact vision-based sensor.” Measurement 99 (Mar): 44–52.
Fujiwara, Y., and T. Sakai. 2016. “A study of a lift-off test method for ground anchors.” J. JSCE 4 (1): 106–117.
Geier, R., G. De Roeck, and R. Flesch. 2006. “Accurate cable force determination using ambient vibration measurements.” Struct. Infrastruct. Eng. 2 (1): 43–52.
Gentile, C. 2010. “Deflection measurement on vibrating stay cables by non-contact microwave interferometer.” NDT&E Int. 43 (3): 231–240.
Gimsing, N. J. 1997. Cable supported bridges, concept & design. 2nd ed. Chichester, UK: Wiley.
Haji Agha Mohammad Zarbaf, S. E., M. Norouzi, R. J. Allemang, V. J. Hunt, and A. Helmicki. 2017a. “Stay cable tension estimation of cable-stayed bridges using genetic algorithm and particle swarm optimization.” J. Bridge Eng. 22 (10): 05017008.
Haji Agha Mohammad Zarbaf, S. E., M. Norouzi, R. J. Allemang, V. J. Hunt, A. Helmicki, and D. K. Nims. 2017b. “Stay force estimation in cable-stayed bridges using stochastic subspace identification methods.” J. Bridge Eng. 22 (9): 04017055.
Huang, Y.-H., J.-Y. Fu, Q. Gan, R.-H. Wang, Y.-L. Pi, and A.-R. Liu. 2017. “New method for identifying internal forces of hangers based on form-finding theory of suspension cable.” J. Bridge Eng. 22 (9): 04017055.
Irvine, H. M. 1981. Cable Structures. Cambridge, MA: MIT Press.
Irvine, H. M., and T. K. Caughey. 1974. “The linear theory of free vibrations of a suspended cable.” Proc. R. Soc. London A. 341 (1626): 299–315.
Johnson, E. A., R. E. Christenson, and B. F. Spencer Jr. 2003. “Semiactive damping of cables with sag.” Comput. Aided Civ. Infrastruct. Eng. 18 (2): 132–146.
Kim, S.-W., B.-G. Jeon, J.-H. Cheung, S.-D. Kim, and J.-B. Park. 2017. “Stay cable tension estimation using a vision-based monitoring system under various weather conditions.” J. Civ. Struct. Health Monit.: 7 (3): 1–15.
Kim, S.-W., B.-G. Jeon, N.-S. Kim, and J.-C. Park. 2013. “Vision-based monitoring system for evaluating cable tensile forces on a cable-stayed bridge.” Struct. Health Monit. 12 (5–6): 440–456.
Kim, S.-W., and N.-S. Kim. 2011. “Multi-point displacement response measurement of civil infrastructures using digital image processing.” Procedia Eng. 14: 195–203.
Lardies, J. 2010. “Modal parameter identification based on ARMAV and state–space approaches.” Arch. Appl. Mech. 80 (4): 335–352.
Lardies, J., and T. Minh-Ngi. 2011. “Modal parameter identification of stay cables from output-only measurements.” Mech. Syst. Sig. Process. 25 (1): 133–150.
Mazurek, D. F. 2016. “Vibration-based estimation of tension stress in steel eyebars.” J. Struct. Eng. 142 (12): 04016124.
Mehrabi, A. B., and H. Tabatabai. 1998. “Unified finite difference formulation for free vibration of cables.” J. Struct. Eng. 124 (11): 1313–1322.
Nazarian, E., F. Ansari, and H. Azari. 2016a. “Recursive optimization method for monitoring of tension loss in cables of cable-stayed bridges.” J. Intell. Mater. Syst. Struct. 27 (15): 2091–2101.
Nazarian, E., F. Ansari, X. Zhang, and T. Taylor. 2016b. “Detection of tension loss in cables of cable-stayed bridges by distributed monitoring of bridge deck strains.” J. Struct. Eng. 142 (6): 04016018.
Norouzi, M., S. E. H. A. M. Zarbaf, A. Dalvi, V. Hunt, and A. Helmicki. 2016. A study of thermal response of concrete towers employing linear regression. In Vol. 9804 of Proc., Nondestructive Characterization and Monitoring of Advanced Materials, Aerospace, and Civil Infrastructure 2016 98040G. Bellingham, WA: SPIE (The International Society for Optics and Photonics).
Pacheco, B. M., Y. Fujino, and A. Sulekh. 1993. “Estimation curve for modal damping in stay cables with viscous damper.” J. Struct. Eng. 119 (6): 1961–1979.
Pacitti, A., M. Peigney, F. Bourquin, and W. Lacarbonara. 2017. “Experimental data based cable tension identification via nonlinear static inverse problem.” Procedia Eng. 199: 453–458.
Ren, W.-X., G. Chen, and W.-H. Hu. 2005. “Empirical formulas to estimate cable tension by cable fundamental frequency.” Struct. Eng. Mech. 20 (3): 363–380.
Ricciardi, G., and F. Saitta. 2008. “A continuous vibration analysis model for cables with sag and bending stiffness.” Eng. Struct. 30 (5): 1459–1472.
Scarella, A., G. Salamone, S. K. Babanajad, A. De Stefano, and F. Ansari. 2016. “Dynamic Brillouin scattering-based condition assessment of cables in cable-stayed bridges.” J. Bridge Eng. 22 (3): 04016130.
Sim, S.-H., J. Li, H. Jo, J.-W. Park, S. Cho, B. F. Spencer Jr., and H.-J. Jung. 2013. “A wireless smart sensor network for automated monitoring of cable tension.” Smart Mater. Struct. 23 (2): 025006.
Ta, M.-N., J. Lardies, and B. Marc. 2006. “Natural frequencies and modal damping ratios identification of civil structures from ambient vibration data.” Shock Vibr. 13 (4, 5): 429–444.
Wu, W.-H., C.-C. Chen, and J.-A. Liau. 2012. “A multiple random decrement method for modal parameter identification of stay cables based on ambient vibration signals.” Adv. Struct. Eng. 15 (6): 969–982.
Xu, Y., and Z. Yu. 1998. “Vibration of inclined sag cables with oil dampers in cable-stayed bridges.” J. Bridge Eng. 3 (4): 194–203.
Yang, Y., S. Li, S. Nagarajaiah, H. Li, and P. Zhou. 2015. “Real-time output-only identification of time-varying cable tension from accelerations via complexity pursuit.” J. Struct. Eng. 142 (1): 04015083.
Yang, Y., X. Wang, and Z. Wu. 2014. “Experimental study of vibration characteristics of FRP cables for long-span cable-stayed bridges.” J. Bridge Eng. 20 (4): 04014074.
Yu, Y., C. Zhang, X. Zhu, W. H. Kang, X. Mao, and B. Uy. 2014. “Design and experimental investigations of a vibration based wireless measurement system for bridge cable tension monitoring.” Adv. Struct. Eng. 17 (11): 1657–1668.
Zhang, F., M. Norouzi, V. J. Hunt, and A. Helmicki. 2015. “Structural health monitoring system for Ironton–Russell Bridge, Ohio and Kentucky. Phase 1: Substructure construction.” J. Transp. Res. Board, 2504: 159–167.
Zhao, Y., Z. Wang, X. Zhang, and L. Chen. 2017. “Effects of temperature variation on vibration of a cable-stayed beam.” Int. J. Struct. Stability Dyn. 17 (10): 1750123.
Zui, H., T. Shinke, and Y. Namita. 1996. “Practical formulas for estimation of cable tension by vibration method.” J. Struct. Eng. 122 (6): 651–656.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Aug 3, 2017
Accepted: Dec 8, 2017
Published online: Apr 13, 2018
Published in print: Jun 1, 2018
Discussion open until: Sep 13, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.