Experimental Shear Study of Rivet-Fastened Rectangular Hollow Flange Channel Beams with Web Openings
Publication: Journal of Structural Engineering
Volume 144, Issue 4
Abstract
The rivet-fastened rectangular hollow flange channel beam (RHFCB) is a new cold-formed steel section and is considered to be a substitute for welded hollow flange channel beams. This monosymmetric channel section is made from two torsionally rigid rectangular hollow flanges connected to a web plate using rivets at intermittent spacing. This fabrication process allows great flexibility in selecting different combinations of web and flange element sizes to attain optimum design capacities. Although the shear behavior of the commonly used lipped channel beam (LCB) and welded hollow flange beam (HFB) sections, with and without web openings, has been investigated previously, the shear strength and behavior of rivet-fastened RHFCBs with web openings have not been investigated yet. Therefore a series of shear tests was conducted to investigate the shear behavior and strength of rivet-fastened RHFCBs with circular web openings. Simply supported test specimens with aspect ratios of 1.0 and 1.5 were loaded at midspan until failure. The shear capacities determined from the tests were compared with those predicted by current cold-formed steel design standards. The results revealed that the existing design equations were not able to accurately predict the shear capacities of rivet-fastened RHFCBs with circular web openings. This is mainly due to the shear buckling capacity improvements provided by the rectangular hollow flanges and associated postbuckling strength. Hence the shear strength capacity results were used to propose improved design equations for rivet-fastened RHFCBs with circular web openings. This paper presents the details of the shear tests, observations, design capacity comparison, and proposed design equations.
Get full access to this article
View all available purchase options and get full access to this article.
References
AISI (American Iron and Steel Institute). (2012). “North American specification for the design of cold-formed steel structural members.” AISI S100, Washington, DC.
Anapayan, T., and Mahendran, M. (2012). “Improved design rules for hollow flange sections subject to lateral distortional buckling.” Thin Walled Struct., 50(1), 128–140.
Anapayan, T., Mahendran, M., and Mahaarachchi, D. (2011). “Section moment capacity tests of LiteSteel beams.” Thin Walled Struct., 49(4), 502–512.
Carvalho, E. C. G., Van den Berg, G. J., and Van der Merwe, P. (1992). “Behaviour of cold-formed stainless steel beams subjected to shear.”, Structural Stability Research Council, Pittsburgh.
Eiler, M. R. (1997). “Behavior of web elements with openings subjected to linearly varying shear.” M.S. thesis, Univ. of Missouri-Rolla, Rolla, MO.
Keerthan, P., Hughes, D., and Mahendran, M. (2014a). “Experimental studies of hollow flange channel beams subject to combined shear and bending actions.” Thin Walled Struct., 77(1), 129–140.
Keerthan, P., and Mahendran, M. (2008). “Shear behaviour of LiteSteel beams.” Proc., 5th Int. Conf. on Thin-Walled Structures, Queensland Univ. of Technology, Brisbane, QLD, Australia, 411–418.
Keerthan, P., and Mahendran, M. (2010a). “Elastic shear buckling characteristics of LiteSteel beams.” J. Constr. Steel Res., 66(11), 1309–1319.
Keerthan, P., and Mahendran, M. (2010b). “Experimental studies on the shear behaviour and strength of LiteSteel beams.” Eng. Struct., 32(10), 3235–3247.
Keerthan, P., and Mahendran, M. (2011). “New design rules for the shear strength of LiteSteel beams.” J. Constr. Steel Res., 67(6), 1050–1063.
Keerthan, P., and Mahendran, M. (2013). “New design rules for the shear strength of LiteSteel beams with web openings.” J. Struct. Eng., 1428–1439.
Keerthan, P., and Mahendran, M. (2014). “Improved shear design rules for lipped channel beams with web openings.” J. Constr. Steel Res., 97(1), 127–142.
Keerthan, P., and Mahendran, M. (2015a). “Experimental investigation and design of lipped channel beams in shear.” Thin Walled Struct., 86(1), 174–184.
Keerthan, P., and Mahendran, M. (2015b). “Numerical modelling of rivet fastened rectangular hollow flange channel beam subject to shear.” Proc., 8th Int. Conf. on Advances in Steel Structures (ICASS’2015), Instituto Superior Técnico, Portugal.
Keerthan, P., and Mahendran, M. (2016). “Shear tests of rivet fastened rectangular hollow flange channel beams.” J. Constr. Steel Res., 121(1), 330–340.
Keerthan, P., Mahendran, M., and Hughes, D. (2014b). “Numerical studies and design of hollow flange channel beams subject to combined bending and shear actions.” Eng. Struct., 75(1), 197–212.
Keerthan, P., Mahendran, M., and Steau, E. (2014c). “Experimental study of web crippling behaviour of hollow flange channel beams under two flange load cases.” Thin Walled Struct., 85(1), 207–219.
LaBoube, R. A., and Yu, W. W. (1978). “Cold-formed steel beam webs subjected primarily to shear.”, Univ. of Missouri-Rolla, Rolla, MO.
OATM (OneSteel Australian Tube Mills). (2008). Design of LiteSteel beams, Brisbane, QLD, Australia.
Pham, C. H., and Hancock, G. J. (2010). “Experimental investigation of high strength C sections in combined bending and shear.” J. Struct. Eng., 866–878.
SA (Standards Australia). (2005). “Cold-formed steel structures.”, Sydney, Australia.
Schuster, R. M. (1995). “Research into cold formed steel perforated C-sections in shear.”, Univ. of Waterloo, Waterloo, ON, Canada.
Seo, J. K., and Mahendran, M. (2011). “Plastic bending behaviour and section moment capacities of mono-symmetric LiteSteel beams with web openings.” Thin Walled Struct., 49(4), 513–522.
Seo, J. K., and Mahendran, M. (2012). “Member moment capacities of mono-symmetric LiteSteel beam floor joists with web openings.” J. Constr. Steel Res., 70(1), 153–166.
Shan, M. Y., LaBoube, R. A., Langan, J. E., and Yu, W. W. (1997). “Cold-formed steel webs with openings: Summary report.” Thin Walled Struct., 27(1), 79–84.
Siahaan, R., Keerthan, P., and Mahendran, M. (2014a). “Numerical studies of rivet-fastened rectangular hollow flange channel beams.” Proc., 22nd Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, MO, 259–276.
Siahaan, R., Keerthan, P., and Mahendran, M. (2014b). “Section moment capacity tests of rivet fastened rectangular hollow flange channel beams.” Proc., 22nd Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, MO, 277–294.
Yu, W. W. (2000). Cold-formed steel design, 3rd Ed., Wiley, New York.
Information & Authors
Information
Published In
Copyright
©2018 American Society of Civil Engineers.
History
Received: Apr 7, 2016
Accepted: Aug 2, 2017
Published online: Feb 2, 2018
Published in print: Apr 1, 2018
Discussion open until: Jul 2, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.