Performance of D-Regions Affected by Alkali-Silica Reaction: Experimental and Analytical Study
Publication: Journal of Structural Engineering
Volume 143, Issue 9
Abstract
This paper describes the experimental performance of D-region reinforced concrete bent specimens affected by varying levels of alkali-silica reaction (ASR) from none to mid-to-late stages, as determined from petrography analysis and from the presence and extent of concrete expansion and cracking. It also describes the analytical methodology employed. It is shown that specimens showing varying degrees of ASR compared with the control specimen without ASR had slightly greater stiffness, strength, and ductility, with no evident detrimental effects on structural response. The apparent improved behavior can be explained as a result of the activation of the specimen’s reinforcing steel due to concrete expansion primarily from ASR, which effectively prestresses and confines the core concrete. Analytically, conventional code-based methods, including sectional analysis and strut-and-tie modeling (STM), underestimate the strength capacity of the specimens when tested to failure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This project was conducted at Texas A&M University through the Texas Transportation Institute and was supported by the Texas Department of Transportation and the Federal Highway Administration. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the authors and do not necessarily reflect the view of the sponsors.
References
AASHTO. (2010). LRFD bridge design specifications, 5th Ed., Washington, DC.
ACI (American Concrete Institute). (2008). “Building code requirements for structural concrete (ACI 318-08) and commentary.” ACI Committee 318, Farmington Hills, Michigan.
ASTM. (2007a). “Standard practice for making and curing concrete test specimens in the field.” ASTM C31, West Conshohocken, Pennsylvania.
ASTM. (2007b). “Standard test method for compressive strength of cylindrical concrete specimens.” ASTM C39, West Conshohocken, Pennsylvania.
Bérubé, M.-A., Chouinard, D., Pigeon, M., Frenette, J., Boisvert, L., and Rivest, M. (2002). “Effectiveness of sealers in counteracting alkali-silica reaction in plain and air-entrained laboratory concretes exposed to wetting and drying, freezing and thawing, and salt water.” Can. J. Civil Eng., 29(2), 289–300.
Birrcher, D., Tuchscherer, R., Huizinga, M., Bayrak, O., Wood, S., and Jirsa, J. (2009). “Strength and serviceability design of reinforced concrete deep beams.”, Center for Transportation Research, Univ. of Texas at Austin, Austin, TX.
Bracci, J. M., Gardoni, P., Eck, M. K., and Trejo, D. (2012). “Performance of lap splices in large-scale column specimens affected by ASR and/or DEF.”, Texas Transportation Institute, Texas A&M Univ. System, College Station, TX.
Courtier, R. H. (1990). “Assessment of ASR-affected structures.” Cem. Concr. Compos., 12(3), 191–201.
Deschenes, D. J., Bayrak, O., and Folliard, K. J. (2009). “ASR/DEF-damaged bent caps: Shear tests and field implications.”, Ferguson Structural Engineering Laboratory, Univ. of Texas at Austin, Austin, TX.
Fan, S., and Hanson, J. M. (1998). “Length expansion and cracking of plain and reinforced concrete prisms due to alkali-silica reaction.” ACI Mater. J., 95(4), 480–485.
Folliard, K. J., et al. (2006). “Preventing ASR/DEF in new concrete: Final report.”, Center for Transportation Research, Univ. of Texas at Austin, Austin, TX.
Hobbs, D. W. (1984). “Expansion of concrete due to alkali-silica reaction.” Struct. Eng., 62A(1), 26–34.
Jensen, V. (2003). “Elgeseter bridge in Trondheim damaged by alkali silica reaction: Microscopy, expansion and relative humidity measurements, treatment with mono silanes and repair.” 9th Euroseminar on Microscopy Applied to Building Materials, Trondheim, Norway.
Liu, S.-H. (2012). “Structural assessment of D-regions affected by alkali-silica reaction/delayed ettringite formation.” Ph.D. dissertation, Texas A&M Univ., College Station, TX.
Liu, S.-H., Bracci, J. M., Mander, J. B., and Hurlebaus, S. (2015). “Performance of D-regions affected by ASR: Accelerated exposure and damage.” ACI Mater. J., 112(4), 501–511.
Mander, J. B., et al. (2012). “Structural assessment of” D” region affected by premature concrete deterioration: Technical report.”, Texas Transportation Institute, Texas A&M Univ. System, College Station, TX.
Marti, P. (1985). “Basic tools of reinforced concrete beam design.” J. Am. Concr. Inst., 82(1), 46–56.
Mohammed, T. U., Hamada, H., and Yamaji, T. (2003). “Alkali-silica reaction-induced strains over concrete surface and steel bars in concrete.” ACI Mater. J., 100(2), 133–142.
Schlaich, J., Schäfer, K., and Jennewein, M. (1987). “Toward a consistent design of structural concrete.” PCI J., 32(3), 74–150.
Tuchscherer, R. G., Birrcher, D. B., and Bayrak, O. (2011). “Strut-and-tie model design provisions.” PCI J., 56(1), 155–170.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Jul 14, 2016
Accepted: Mar 16, 2017
Published online: Jun 10, 2017
Published in print: Sep 1, 2017
Discussion open until: Nov 10, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.