Experimental Assessment of the System-Level Seismic Performance of an Asymmetrical Reinforced Concrete Block–Wall Building with Boundary Elements
Publication: Journal of Structural Engineering
Volume 143, Issue 8
Abstract
Using boundary elements in reinforced masonry (RM) walls allows closed ties to be used and multiple layers of vertical bars to be accommodated, thus providing a confining reinforcement cage. This enhances the overall performance of the RM wall relative to conventional RM wall with rectangular cross sections, which typically have a single-leg horizontal reinforcement and a single layer of vertical reinforcement. In addition, with the expected shift of design code developers’ focus from the component-level to the system-level assessment of seismic force resisting systems (SFRS), there is a need to experimentally quantify the system-level performance of RM buildings. To address this, an experimental asymmetrical two-story reduced-scale RM shear wall building with boundary elements, referred to as “Building IV,” was tested to failure under reversed cyclic loading that simulates seismic demands. Building IV was designed to have the same lateral resistance as a previously tested RM shear wall building with conventional rectangular configuration (without boundary elements), referred to as “Building III,” to allow for direct comparison. Therefore, after a brief summary of the experimental program, the focus of this paper is to compare the damage sequence and the load-displacement hysteretic behavior between the two buildings. The results show that higher levels of ductility accompanied by relatively smaller strength degradation were achieved during the test of Building IV compared to that of Building III. This study enlarges the database of system-level experimental results in an effort to facilitate the adoption of RM shear walls with boundary elements as a SFRS category within the next editions of the American and the Canadian masonry design standards.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The financial support for this project was provided through the Natural Sciences and Engineering Research Council (NSERC) of Canada. Support was also provided by the McMaster University Centre for Effective Design of Structures (CEDS), funded through the Ontario Research and Development Challenge Fund (ORDCF) of the Ministry of Research and Innovation (MRI). Provision of mason time by the Ontario Masonry Contractors Association (OMCA) and the Canada Masonry Design Centre (CMDC) is appreciated. The provision of the scaled blocks through a grant from the Canadian Concrete Masonry Producers Association (CCMPA) is gratefully acknowledged.
References
Abrams, D. (1986). “Measured hysteresis in a masonry building system.” Proc., 3rd U.S. Conf. on Earthquake Engineering, Earthquake Engineering Research Institute, Oakland, CA.
Ahmadi, F., Hernandez, J., Sherman, J., Kapoi, C., Klingner, R., and McLean, D. (2014). “Seismic performance of cantilever-reinforced concrete masonry shear walls.” J. Struct. Eng., .
ASCE. (2014). “Seismic evaluation and retrofit of existing buildings.” ASCE 41-13, Reston, VA.
Ashour, A., and El-Dakhakhni, W. (2016). “Influence of floor diaphragm-wall coupling on the system-level seismic performance of an asymmetrical reinforced concrete block building.” J. Struct. Eng., .
Ashour, A., El-Dakhakhni, W., and Shedid, M. (2016). “Experimental evaluation of the system-level seismic performance and robustness of an asymmetrical reinforced concrete block building.” J. Struct. Eng, .
ASTM. (2008a). “Standard test method for sampling and testing grout.” ASTM CI019-08, West Conshohocken, PA.
ASTM. (2008b). “Standard test methods for sampling and testing concrete masonry units and related units.” ASTM C140-08, West Conshohocken, PA.
Banting, B., and El-Dakhakhni, W. (2012). “Force- and displacement-based seismic performance parameters for reinforced masonry structural walls with boundary elements.” J. Struct. Eng., 1477–1491.
Banting, B., and El-Dakhakhni, W. (2014). “Seismic performance quantification of reinforced masonry structural walls with boundary elements.” J. Struct. Eng., .
Banting, B. R. (2013). “Seismic performance quantification of concrete block masonry structural walls with confined boundary elements and development of the normal strain-adjusted shear strength expression (NSSSE).” Ph.D. thesis, McMaster Univ., Hamilton, ON, Canada.
Brunner, J. D. (1994). “Shear strength of reinforced masonry walls.” M.S. thesis, Dept. of Civil, Environmental, and Architectural Engineering, Univ. of Colorado, Boulder, CO.
Chopra, A. (2007). Dynamics of structures: Theory and application to earthquake engineering, 3rd Ed., Prentice Hall, Upper Saddle River, NJ.
Cohen, G. L., Klinger, R. L., Hayes, J. R., Jr., and Sweeny, S. C. (2004). “Seismic evaluation of low-rise reinforced masonry buildings with flexible diaphragms. I: Seismic and quasi-static testing.” Earthquake Spectra, 20(3), 779–801.
CSA (Canadian Standards Association). (2014a). “Standards on concrete masonry units.” CSA A165-14, Mississauga, ON, Canada.
CSA (Canadian Standards Association). (2014b). “Carbon steel bars for concrete reinforcement.” CSA G30.18-09, Mississauga, ON, Canada.
CSA (Canadian Standards Association). (2014c). “Design of masonry structures.” CSA S304-14, Mississauga, ON, Canada.
CSA (Canadian Standards Association). (2014d). “Mortar and grout for unit masonry.” CSA A179-14, Mississauga, ON, Canada.
Dhanasekar, M., and Shrive, N. G. (2002). “Strength and deformation of confined and unconfined grouted concrete masonry.” ACI Struct. J., 99(6), 819–826.
El Ezz, A. A., Seif Eldin, H. M., and Galal, K. (2015). “Influence of confinement reinforcement on the compression stress-strain of grouted reinforced concrete block masonry boundary elements.” Structures, 2, 32–43.
FEMA. (2009). “Effects of strength and stiffness degradation on seismic response.” FEMA P440A, Washington, DC.
Hart, G. C., Sajjad, N., Kingsley, G. R., and Noland, J. L. (1989). “Analytical stress-strain curves for grouted concrete masonry.” Masonry Soc. J., 8(1), 21–34.
Heerema, P., Ashour, A., Shedid, M., and El-Dakhakhni, W. (2015). “System-level displacement and performance-based seismic design parameter quantifications for an asymmetrical reinforced concrete masonry building.” J. Struct. Eng., .
Hose, Y., and Seible, F. (1999). “Performance evaluation database for concrete bridge components, and systems under simulated seismic loads.”, Pacific Earthquake Engineering Research Center, College of Engineering, Univ. of California, Berkeley, CA.
Ibarra, L. F., Medina, R. A., and Krawinkler, H. (2005). “Hysteretic models that incorporate strength and stiffness deterioration.” Earthquake Eng. Struct. Dyn., 34(12), 1489–1511.
Ibrahim, K. S., and Sutter, G. T. (1999). “Ductility of concrete masonry shear walls subjected to cyclic loading.” Proc., 8th North American Masonry Conf., Austin, TX.
Maier, J., and Thürlimann, B. (1985). “Bruchversuche an Stahlbetonscheiben.”, Bericht/Institut für Baustatik und Konstruktion, ETH Zürich, Switzerland.
Mayes, R. L., Omote, Y., and Clough, R. W. (1976). “Cyclic shear tests of masonry piers. Volume 1: Test results.”, Earthquake Engineering Research Center, Univ. of California, Berkeley, CA.
Miranda, E., and Bertero, V. (1994). “Evaluation of strength-reduction factors for earthquake-resistant design.” Earthquake Spectra, 10(2), 357–379.
Mostaghel, N. (1999). “Analytical description of pinching, degrading hysteretic systems.” J. Eng. Mech., 216–224.
MSJC (Masonry Standards Joint Committee). (2013). “Building code requirements and specifications for masonry structures.”, Detroit.
Park, Y. J., Reinhorn, A. M., and Kunnath, S. K. (1987). “IDARC: Inelastic damage analysis of reinforced concrete frame, shear-wall, structures.”, State Univ. of New York at Buffalo, Buffalo, NY.
Priestley, M. J. N. (1976). “Cyclic testing of heavily reinforced concrete masonry shear walls.”, Univ. of Canterbury, Christchurch, New Zealand.
Priestley, M. J. N., and Bridgeman, D. O. (1974). “Seismic resistance of brick masonry walls.” Bull. N.Z. Natl. Soc. Earthquake Eng., 7(4), 167–187.
Priestley, M. J. N., and Elder, D. M. (1982). “Cyclic loading tests of slender concrete masonry shear walls.” Bull. N.Z. Natl. Soc. Earthquake Eng., 15(1), 3–21.
Priestley, M. N., Seible, F., and Calvi, G. M., (1996). Seismic design and retrofit of bridges, Wiley, Hoboken, NJ.
Priestley, N., Calvi, G., and Kowalsky, M. (2007). Displacement-based seismic design of structures, IUSS, Pavia, Italy.
Seible, F., Hegemier, G., Priestley, M. J. N., Kingsley, G., Igarashi, A., and Kurkchubasche, A. (1993). “Preliminary results from the TCCMAR 5-story full scale reinforced masonry research building test.” Masonry Soc. J., 12(1), 53–60.
Seible, F., Priestley, M. J. N., Kingsley, G., and Kurkchubasche, A. (1994). “Seismic response of full scale five story reinforced masonry building.” J. Struct. Eng., 925–946.
Shedid, M., Drysdale, R., and El-Dakhakhni, W. (2008). “Behaviour of fully grouted reinforced concrete masonry shear walls failing in flexure: Experimental results.” J. Struct. Eng., 1754–1767.
Shedid, M. T., El-Dakhakhni, W. W., and Drysdale, R. G. (2009). “Behavior of fully grouted reinforced concrete masonry shear walls failing in flexure: Analysis.” Eng. Struct., 31(9), 2032–2044.
Shedid, M. T., El-Dakhakhni, W. W., and Drysdale, R. G. (2010). “Alternative strategies to enhance the seismic performance of reinforced concrete-block shear wall systems.” J. Struct. Eng., 676–689.
Sivaselvan, M. V., and Reinhorn, A. M. (2000). “Hysteretic models for deteriorating inelastic structures.” J. Eng. Mech., 633–640.
Siyam, M., El-Dakhakhni, W., Shedid, M., and Drysdale, R. (2015). “Seismic response evaluation of ductile reinforced concrete block structural walls. I: Experimental results and force-based design parameters.” J. Perform. Constr. Facil.,.
Stavridis, A., et al. (2011). “Shake-table tests of a 3-story, full-scale masonry wall system.” Proc., ACI Masonry Seminar, Masonry Society, Longmont, CO.
Tomaževič, M. (1998). Earthquake-resistant design of masonry buildings, Imperial College Press, London.
Tomaževič, M., and Weiss, P. (1994). “Seismic behavior of plain- and reinforced-masonry buildings.” J. Struct. Eng., 323–338.
Voon, K. C., and Ingham, J. M. (2006). “Experimental in-plane shear strength investigation of reinforced concrete masonry walls.” J. Struct. Eng., 400–408.
Zonta, D., Zanardo, G., and Modena, C. (2001). “Experimental evaluation of the ductility of a reduced-scale reinforced masonry building.” Mater. Struct., 34(244), 636–644.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Dec 22, 2015
Accepted: Dec 21, 2016
Published online: Mar 20, 2017
Published in print: Aug 1, 2017
Discussion open until: Aug 20, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.