Reinforced Wood I-Joists with Web Openings
Publication: Journal of Structural Engineering
Volume 143, Issue 6
Abstract
Prefabricated wood I-joists with web openings are commonly used in light-frame wood construction. The capacity and the failure pattern of such I-joists in the presence of a circular web opening were experimentally investigated on 100 specimens with various sizes and locations of web openings and two different span lengths of 3.66 m (12 ft) and 6.10 m (20 ft). The control I-joists, i.e., I-joists without any opening, failed in flexure in the midspan, whereas most of the I-joists with an opening failed in a brittle and sudden shear mode. The presence of an opening reduced the capacity up to 54% compared to I-joists without web openings depending on the size and location of the opening. Subsequently, to prevent brittle failure and improve capacity, the I-joists were reinforced using two perpendicular OSB collar layers with a variation in the reinforcement length. The effectiveness of reinforcing the web around openings was investigated on another 100 specimens. After reinforcement, brittle premature failure of I-joists was prevented with an increase in capacity up to 27% compared to the I-joists with openings. Analytical models to calculate the capacity of unreinforced and reinforced I-joists with openings are proposed, validated with results from previous research, which prove to be more accurate compared to existing models from the literature.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research was supported by the Natural Sciences and Engineering Research Council (NSERC) of Canada through an Engage Grant and Industrial Postgraduate Scholarship (IPS) in collaboration with AcuTruss Industries of Kelowna, British Columbia, Canada. Thanks are also extended to Kader Newaj Siddiquee, for his priceless help during the experimental tests.
References
Afzal, M. T., Lai, S., Chui, Y. H., and Pirzada, G. (2006). “Experimental evaluation of wood I-joists with web holes.” Forest Prod. J., 56(10), 26.
American Forest & Paper Association. (2001). “Allowable stress design (ASD) manual for engineered wood construction.” Washington, DC.
ASCE. (2010). “Minimum design loads for buildings and other structures.” ASCE 7–10, Reston, VA.
ASTM. (2013). “Standard specification for establishing and monitoring structural capacities of prefabricated wood I-joists.” ASTM-D5055, West Conshohocken, PA.
Borri, A., Corradi, M., and Grazini, A. (2005). “A method for flexural reinforcement of old wood beams with CFRP materials.” Compos. Eng., 36(2), 143–153.
CEN (European Committee for Standardization). (1991). “Timber structures: Joints made with mechanical fasteners—General principles for the determination of strength and deformation characteristics.” EN 26891, Brussels, Belgium.
CSA (Canadian Standards Association). (2012). “Construction sheathing.” CSA O325-07, Rexdale, ON, Canada.
CSA (Canadian Standards Association). (2014). “Engineering design in wood.” CSA O86-14, Mississauga, ON, Canada.
Dietsch, P., and Tannert, T. (2015). “Assessing the integrity of glued-laminated timber elements.” Constr. Build. Mater., 101, 1259–1270.
Fergus, D. A. (1979). “Effect of web voids and stiffeners on structural performance of composite I-beam.” Purdue Univ., West Lafayette, IN.
Franke, S., Franke, B., Harte, A. M. (2015). “Failure modes and reinforcement techniques for timber beams: State of the art.” Constr. Build. Mater., 97, 2–13.
Guan, Z. W., and Zhu, E. C. (2004). “Non-linear FE modeling of crack behavior of openings in OSB webbed I-beams.” J. Struct. Eng., 1562–1569.
Guan, Z. W., and Zhu, E. C. (2009). “Finite element modelling of anisotropic elasto-plastic timber composite beams with openings.” Eng. Struct., 31(2), 394–403.
Hallström, S. (1996). “Glass fibre reinforced holes in laminated timber beams.” Wood Sci. Technol., 30(5), 323–337.
Hilson, B. O., and Rodd, P. D. (1984). “The effect of web holes on the behaviour and ultimate shearing strength of timber I-beams with hardboard webs.” Struct. Eng., 62B(4), 69–78.
Islam, A., Nwokoli, S. U., and Debebe, T. (2011). “Bearing capacity of I-joists.” Master’s thesis, Faculty of Science and Engineering, School of Engineering, Linnaeus Univ., Vaxjo, Sweden.
Islam, M. S., Shahnewaz, M., and Alam, M. S. (2015). “Structural capacity of timber I-joist with flange notch: Experimental evaluation.” Constr. Build. Mater., 79, 290–300.
Leichti, R. J., Falk, R. H., and Laufenberg, T. (1990a). “Prefabricated wood I-joists: An industry overview.” Forest Prod. J., 40(3), 15–20.
Leichti, R. J., Falk, R. H., and Laufenberg, T. (1990b). “Prefabricated wood composite I-beams: A literature review.” Wood Fiber Sci., 22(1), 62–79.
Leichti, R. J., and Tang, R. C. (1983). “Analysis of wood composite I-beams with glued flange-web joints.” Proc., Spring Conf. on Society for Experimental Stress Analysis, Brookfield Center, Brookfield, MA, 45–50.
Leichti, R. J., and Tang, R. C. (1986). “Creep analysis of wood composite I-beams.” Proc., Southeastern Conf. on Theoretical and Applied Mechanics XIII, Univ. of Southern Carolina, Columbia, SC, 484–490.
Li, Y. F., Xie, Y. M., and Tsai, M. J. (2009). “Enhancement of the flexural performance of retrofitted wood beams using CFRP composite sheets.” Constr. Build. Mater., 23(1), 411–422.
Maley, J. D. (1987). “Wood I-joists: A closer look.” Proc., Structures Congress, Building Structures, ASCE, New York, 221–35.
Montgomery, D. C. (2008). Design and analysis of experiments, 7th Ed., Wiley, Toronto.
Morris, V., Gustafsson, P. J., and Serrano, E. (1995). “The shear strength of light-weight beams with and without a hole: A preliminary study.” Proc., Wood Mechanics: Workshop on Mechanical Properties of Panel Product, Building Research Establishment, Watford, U.K.
Morrissey, G. C., Dinehart, D. W., and Dunn, W. G. (2009). “Wood I-joists with excessive web openings: An experimental and analytical investigation.” J. Struct. Eng., 655–665.
Nascor. (2010). “Specifier guide NJ, NJH, NJU series I-joists.” Ottawa.
NDS (National Design Specification). (2015). “National design specification for wood construction.” American Forest & Paper Association (AF&PA), American Wood Council, Washington, DC.
Nowak, T. P., Jasienko, J., and Czepizak, D. (2013). “Experimental tests and numerical analysis of historic bent timber elements reinforced with CFRP strips.” Constr. Build. Mater., 40, 197–206.
Pirzada, G. B., Chui, Y. H., and Lai, S. (2008). “Predicting strength of wood I-joist with a circular web hole.” J. Struct. Eng., 1229–1234.
Polocoser, T., Miller, T. H., and Gupta, R. (2013). “Evaluation of remediation techniques for circular holes in the webs of wood I-joists.” J. Mater. Civ. Eng., 1898–1909.
Raftery, G. M., and Harte, A. M. (2011). “Low-grade glued laminated timber reinforced with FRP plate.” Compos. Eng., 42(4), 724–735.
Samson, M. (1983). “Influence of flange quality on the load-carrying capacity of composite webbed I-beams in flexure.” Forest Prod. J., 33(1), 38–42.
Vallée, T., Tannert, T., and Fecht, S. (2017). “Adhesively bonded connections in the context of timber engineering: A review.” J. Adhesion, 93(4), 257–287.
Voluntary Product Standard. (2010). “Performance standard for wood-based structural-use panels.”, National Institute of Standards and Technology, Washington, DC.
Wang, A., and Cheng, J. J. R. (1995). “Shear behaviour of OSB wood composite I-beams with web opening.” Canadian Forest Service, Dept. of Civil Engineering, Edmonton, AB, Canada.
WIJMA (Wood I-Joist Manufacturers Association). (1999). “Establishing shear capacities for prefabricated wood I-joists with hole.” American Forest & Paper Association, Washington, DC.
Williams, L. J., and Abdi, H. (2010). “Fisher’s least significant difference (LSD) test.” Encyclopedia of research design, Sage Publications, Thousand Oaks, CA, 1–5.
Zhu, E. C., Guan, Z. W., Pope, D. J., and Rodd, P. D. (2007). “Effects of openings on oriented strand board webbed wood I-joists.” J. Struct. Eng., 145–149.
Zhu, E. C., Guan, Z. W., Rodd, P. D., and Pope, D. J. (2005). “Finite element modelling of OSB webbed timber I-beams with interactions between openings.” Adv. Eng. Software, 36(11-12), 797–805.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Oct 14, 2015
Accepted: Nov 4, 2016
Published ahead of print: Feb 12, 2017
Published online: Feb 13, 2017
Published in print: Jun 1, 2017
Discussion open until: Jul 13, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.