Numerical Modeling of Thin-Walled Steel Roof Battens Subject to Pull-Through Failures
Publication: Journal of Structural Engineering
Volume 143, Issue 6
Abstract
Extensive damage to light gauge steel roofing systems caused by high wind events such as cyclones and storms has been a concern to the communities living in cyclone/storm prone areas over many years. In recent times, pull-through failures of roof battens occurring in their bottom flange to rafter or truss connection have become the main reason for severe roof failures. Therefore, a detailed experimental study was first undertaken using full-scale and small-scale tests to investigate the pull-through failures of roof battens subject to high wind uplift loads. However, since experimental tests can be expensive and time consuming, the ability to successfully use numerical models is imperative. Hence a detailed numerical study was undertaken by developing suitable finite-element models with the inclusion of a suitable failure criterion to predict the initiation of critical pull-through failures of roof battens that are associated with a tearing fracture around the screw fastener head edge. The overall load versus deformation behavior, ultimate failure loads, and failure modes were compared with the experimental results to validate the developed finite-element models. The ability of the validated finite-element models to accurately predict the pull-through failure loads of roof battens for other cases was evaluated by comparing relevant experimental results. This paper presents the details of this numerical study and the results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to thank Australian Research Council for their financial support (DP120103366) and Queensland University of Technology for providing the necessary facilities to conduct this research.
References
ABAQUS [Computer software]. Dassault Systèmes, Waltham, MA.
Atkins, A. G., and Mai, Y. W. (1985). Elastic and plastic fracture, Ellis Horwood Limited, Chichester, U.K.
Beck, V. R., and Stevens, L. K. (1979). “Wind loading failures of corrugated roof cladding.” Civ. Eng. Trans. Inst. Eng., 21(1), 45–56.
Bluescope Steel Limited. (2012). “Lysaght Topspan design manual.” ⟨http://www.lysaght.com/⟩ (Sep. 1, 2012).
Boughton, G. N., and Falck, D. J. (2007). “Tropical cyclone George damage to buildings in the port hedland area.”, James Cook Univ., Townsville, Australia.
Boughton, G. N., and Falck, D. J. (2008). “Shoalwater and Roleystone, WA tornadoes wind damage to buildings.”, James Cook Univ., Townsville, Australia.
Chung, K. F., and Ip, K. H. (2000). “Finite element modeling of bolted connections between cold-formed steel strips and hot rolled steel plates under static shear loading.” Eng. Struct., 22(10), 1271–1284.
Chung, K. F., and Ip, K. H. (2001). “Finite element investigation on the structural behaviour of cold-formed steel bolted connections.” Eng. Struct., 23(9), 1115–1125.
Kiran, R., and Khandelwal, K. (2014). “Fast-to-compute weakly coupled ductile fracture model for structural steels.” J. Struct. Eng., .
Liu, B., Villavicencio, R., and Soares, C. G. (2013). “Experimental and numerical plastic response and failure of laterally impacted rectangular plates.” J. Offshore Mech. Arct. Eng., 135(4), .
Lu, W., Ma, Z., Makelainen, P., and Outinen, J. (2012). “Behaviour of shear connectors in cold-formed steel sheeting at ambient and elevated temperatures.” Thin Walled Struct., 61, 229–238.
Lu, W., Makelainen, P., and Outinen, J. (2008). “Finite element modeling of single lap shear screw connection in steel sheeting in fire.” Open Constr. Build. Technol. J., 2(1), 257–261.
Luo, M., and Wierzbicki, T. (2010). “Numerical failure analysis of a stretch-bending test on dual-phase steel sheets using a phenomenological fracture model.” Int. J. Solids Struct., 47(22), 3084–3102.
Mahaarachchi, D., and Mahendran, M. (2004). “Finite element analysis and design of crest-fixed trapezoidal steel claddings with wide pans subject to pull-through failures.” Eng. Struct., 26(11), 1547–1559.
Mahaarachchi, D., and Mahendran, M. (2009a). “A strain criterion for pull-through failures in crest-fixed steel claddings.” Eng. Struct., 31(2), 498–506.
Mahaarachchi, D., and Mahendran, M. (2009b). “Wind uplift strength of trapezoidal steel cladding with closely spaced ribs.” J. Wind Eng. Ind. Aerodyn., 97(3), 140–150.
Mahendran, M. (1990). “Static behaviour of corrugated roofing under simulated wind loading.” Civ. Eng. Trans. Inst. Eng., 32(4), 212–218.
Mahendran, M. (1994). “Profiled steel roof claddings under high wind forces.” J. Singapore Struct. Steel Soc., 5(1), 95–106.
Mahendran, M. (1995). “Towards an appropriate fatigue loading sequence for roof claddings in cyclone prone areas.” Eng. Struct., 17(7), 476–484.
Mahendran, M., and Mahaarachchi, D. (2002). “Cyclic pull-out strength of screwed connections in steel roof and wall cladding systems using thin steel battens.” J. Struct. Eng., 771–778.
Mahendran, M., and Tang, R. B. (1998). “Pull-out strength of steel roof and wall cladding systems.” J. Struct. Eng., 1192–1201.
Morgan, J. W., and Beck, V. R. (1977). “Failure of sheet-metal roofing under repeated wind loading.” Civ. Eng. Trans. Inst. Eng., 19(1), 1–5.
MSC PATRAN [Computer software]. MSC Software Corporation, Santa Ana, CA.
Oh, C. S., Kim, N. H., Kim, Y. J., Baek, J. H., Kim, Y. P., and Kim, W. S. (2011). “A finite element ductile failure simulation method using stress-modified fracture strain model.” Eng. Fract. Mech., 78(1), 124–137.
Rogers, C. A., and Hancock, G. J. (1997). “Ductility of G550 sheet steels in tension.” J. Struct. Eng., 1586–1594.
Rusinek, A., Rodriguez-Martinez, J. A., Zaera, R., Klepaczko, J. R., Arias, A., and Sauvelet, C. (2009). “Experimental and numerical study on the perforation process of mild steel sheets subjected to perpendicular impact by hemispherical projectiles.” Int. J. Impact Eng., 36(4), 565–587.
Salih, E. L., Gardner, L., and Nethercot, D. A. (2010). “Numerical investigation of net section failure in stainless steel bolted connections.” J. Construct. Steel Res., 66(12), 1455–1466.
Simulia. (2012). ABAQUS analysis user’s manual version 6.12, Dassault Systemes, Providence, RI.
Sivapathasundaram, M., and Mahendran, M. (2016a). “Development of suitable test methods for the screw connections in cold-formed steel roof battens.” J. Struct. Eng., .
Sivapathasundaram, M., and Mahendran, M. (2016b). “Experimental studies of thin-walled steel roof battens subject to pull-through failures.” Eng. Struct., 113, 388–406.
Villavicencio, R., and Soares, C. G. (2012). “Numerical plastic response and failure of a pre-notched transversely impacted beam.” Ships Offshore Struct., 7(4), 417–429.
Xu, Y. L., and Teng, J. G. (1994). “Local plastic failure of light gauge steel roofing sheets: Finite element analysis versus experiment.” J. Construct. Steel Res., 30(2), 125–150.
Information & Authors
Information
Published In
Copyright
©2017 American Society of Civil Engineers.
History
Received: Sep 1, 2015
Accepted: Oct 28, 2016
Published online: Feb 1, 2017
Published in print: Jun 1, 2017
Discussion open until: Jul 1, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.