Experimental Cyclic Testing of URM Pier-Spandrel Substructures
Publication: Journal of Structural Engineering
Volume 143, Issue 2
Abstract
Most current assessment methods for determining the capacity of perforated unreinforced masonry (URM walls) loaded in-plane are based on the assumption of infinitely rigid spandrel elements. Based on observations of damage following past earthquakes, this assumption has been proven to be invalid for certain perforated wall geometries. The reported study was conducted with the primary aim of investigating global and local response of perforated URM walls, with an emphasis placed on defining the influence of the spandrel geometry on the system level response of perforated URM walls responding in-plane. Pseudostatic cyclic testing of six replicated URM full-scale pier-spandrel substructures was conducted to investigate the variables that control spandrel failure modes and the influence of spandrel failure on the lateral capacity of multistory URM walls. Testing showed that the behavior of the spandrel has a significant effect on the failure mode of the piers and hence the strength, stiffness, and energy-dissipation capacity of the system.
Get full access to this article
View all available purchase options and get full access to this article.
References
ASCE. (2007). “Seismic rehabilitation of existing buildings.” ASCE/SEI 41-06, Reston, VA.
ASCE. (2013). “Seismic evaluation and retrofit of existing buildings.” ASCE 41-13, Reston, VA.
ASTM. (2000). “Standard test method for measurement of masonry flexural bond strength.” ASTM C1072-00a, West Conshohocken, PA.
ASTM. (2004). “Standard test method for Young’s modulus, tangent modulus, and chord modulus.” ASTM E1111-04(2010), West Conshohocken, PA.
ASTM. (2011a). “Standard test method for compressive strength of hydraulic cement mortars (using 2-in or 50-mm cube specimens).” ASTM C109/C 109M-11, West Conshohocken, PA.
ASTM. (2011b). “Standard test method for compressive strength of masonry prisms.” ASTM C1314-11, West Conshohocken, PA.
ASTM. (2011c). “Standard test methods for sampling and testing brick and structural clay tile.” ASTM C67-11, West Conshohocken, PA.
Augenti, N., Parisi, F., Prota, A., and Manfredi, G. (2011). “In-plane lateral response of a full-scale masonry sub-assemblage with and without an inorganic matrix-grid strengthening system.” J. Compos. Constr., 578–590.
Beyer, B., and Dazio, A. (2012). “Quasi-static cyclic tests on masonry spandrels.” Earthquake Spectra, 28(3), 907–929.
Cattari, S., and Lagomarsino, S. (2008). “A strength criterion for the flexural behaviour of spandrels in unreinforced masonry walls.” Proc., 14th World Conf. on Earthquake Engineering, Beijing.
CEN (European Committee for Standardization). (2005). “Design of structures for earthquake resistance. Part 3: Assessment and retrofitting of buildings.” Eurocode 8, ENV 1998-3, Brussels, Belgium.
Chopra, A. K. (2007). Dynamics of structures—Theory and applications to earthquake engineering, Pearson, Prentice Hall, NJ.
Dizhur, D., et al. (2011). “Performance of masonry buildings and churches in the 22 February 2011 Christchurch earthquake.” Bull. N. Z. Soc. Earthquake Eng., 44(4), 279–297.
Dizhur, D., and Ingham, J. M. (2013). “Diagonal tension strength of vintage unreinforced clay brick masonry wall panels.” Constr. Build. Mater., 43, 418–427.
Dizhur, D., Ismail, N., Knox, C., Lumantarna, R., and Ingham, J. M. (2010). “Performance of unreinforced and retrofitted masonry buildings during the 2010 Darfield earthquake.” Bull. N. Z. Soc. Earthquake Eng., 43(4), 321–339.
Gattesco, N., Macorini, L., Clemente, I., and Noe, S. (2010). “Shear resistance of spandrels in brick-masonry buildings.” Proc., 8th Int. Masonry Conf., Dresden, Germany.
Giamundo, V., Sarhosis, V., Lignola, G. P., Sheng, Y., and Manfredi, G. (2014). “Evaluation of different computational modelling strategies for the analysis of low strength masonry structures.” Eng. Struct., 73, 160–169.
Lumantarna, R., Biggs, D., and Ingham, J. (2014). “Uniaxial compressive strength and stiffness of field-extracted and laboratory-constructed masonry prisms.” J. Mater. Civ. Eng., 567–575.
Magenes, G., and Calvi, G. M. (1997a). “In-plane seismic response of brick masonry walls.” Earthquake Eng. Struct. Dyn., 26(11), 1091–1112.
Magenes, G., and Calvi, G. M. (1997b). “In-plane seismic response of brick masonry walls.” Earthquake Eng. Struct. Dyn., 26(11), 1091–1112.
Milani, G., Beyer, K., and Dazio, A. (2009). “Upper bound limit analysis of meso-mechanical spandrel models for the pushover analysis of 2D masonry frames.” Eng. Struct., 31(11), 2696–2710.
Moon, L., et al. (2014). “The demise of the URM building stock in Christchurch during the 2010–2011 Canterbury earthquake sequence.” Earthquake Spectra, 30(1), 253–276.
NTC. (2008). “Norme tecniche per le costruzioni—NTC 2008.” Ministero delle Infrastrutture, Rome (in Italian).
NZSEE (New Zealand Society for Earthquake Engineering). (2006). “Assessment and improvement of the structural performance of buildings and earthquakes: Recommendations of a NZSEE study group on earthquake risk buildings.” Wellington, New Zealand.
NZSEE (New Zealand Society for Earthquake Engineering). (2015). “Assessment and improvement of the structural performance of buildings and earthquakes: Section 10 revision seismic assessment of unreinforced masonry buildings.” Wellington, New Zealand.
Parisi, F., Augenti, N., Balsamo, A., Prota, A., and Manfredi, G. (2010). “Lateral load tests on a masonry system with and without external reinforcement.” Proc., 14th European Conf. on Earthquake Engineering, Macedonian Association for Earthquake Engineering (MAEE).
Parisi, F., Augenti, N., and Prota, A. (2014). “Implications of the spandrel type on the lateral behavior of unreinforced masonry walls.” Earthquake Eng. Struct. Dyn., 43(12), 1867–1887.
Parisi, F., Lignola, G. P., Augenti, N., Prota, A., and Manfredi, G. (2011). “Nonlinear behaviour of a masonry sub-assemblage before and after strengthening with inorganic matrix-grid composites.” J. Compos. Constr., 821–832.
Parisi, F., Lignola, G. P., Augenti, N., Prota, A., and Manfredi, G. (2013). “Rocking response assessment of in-plane laterally-loaded masonry walls with openings.” Eng. Struct., 56, 1234–1248.
Park, R. (1989). “Evaluation of ductility of structures and structural assemblages from laboratory testing.” Bull. N. Z. Natl. Soc. Earthquake Eng., 3(22), 155–166.
Priestley, M. J. N., Calvi, M. C., and Kowalsky, M. J. (2007). Displacement-based seismic design of structures, IUSS Press, Pavia, Italy, 670.
Russell, A. P. (2010). “Characterisation and seismic assessment of unreinforced masonry buildings.” Ph.D. thesis, Dept. of Civil Engineering, Univ. of Auckland, Auckland, New Zealand.
Russell, A. P., and Ingham, J. M. (2010). “Prevalence of New Zealand’s unreinforced masonry buildings.” Bull. N. Z. Soc. Earthquake Eng., 43(3), 182–201.
Sheppard, P., and Lutman, M. (1988). Seismic risk assessment and design of building structures, estimation of expected seismic vulnerability: A simple methodology for medium sized groups of older buildings, A. Koridze, ed., Omega Scientific, Wallingford, U.K., 47–62.
Shing, P. B., Noland, J. L., Klamerus, E., and Spaeh, H. (1989). “Inelastic behaviour of concrete masonry shear walls.” J. Struct. Eng., 2204–2225.
Tomaževič, M. (2000). Earthquake-resistant design of masonry buildings—Series on innovation in structures and construction, Vol. 1, Imperial College Press, London.
Tomaževič, M., and Weiss, P. (2010). “Displacement capacity of masonry buildings as a basis for the assessment of behavior factor: An experimental study.” Bull. Earthquake Eng., 8(6), 1267–1294.
Vasconcelos, G., and Lourenco, P. B. (2009). “In-plane experimental behaviour of stone masonry walls under cyclic loading.” J. Struct. Eng., 1269–1277.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Nov 25, 2015
Accepted: Jul 15, 2016
Published online: Sep 22, 2016
Published in print: Feb 1, 2017
Discussion open until: Feb 22, 2017
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.