Seismic Enhancement of Welded Unreinforced Flange-Bolted Web Steel Moment Connections
Publication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
Widespread damage to welded unreinforced flange-bolted web (WUF-B) steel moment connections during the 1994 Northridge earthquake led to intensive research study of this connection. Despite the improvements to weld metal and connection details, the post-Northridge WUF-B connection was unable to attain sufficient ductility for use in special moment frames (SMFs). This study presents detailed finite element (FE) analysis of post-Northridge WUF-B connections to better understand the mechanisms which limited connection ductility in laboratory tests. Observations made from the FE analysis led to the development and numerical study of a modified WUF-B connection that combines a new bolted web design with a recently validated technique to promote plastic hinging of the beam away from the connection joint. The proposed connection provides the benefit of reduced field welding and UT inspection without sacrificing connection ductility and seismic performance. Finally, the proposed connection is experimentally validated through full-scale seismic testing. The pilot test specimen exceeded the AISC 341 qualifying 4% interstory drift angle without significant strength loss. No weld or near-weld cracks were observed. Instead, failure of the connection resulted from large local buckling deformation in the plastic hinge away from the welded joint.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding for this research was provided by the National Science Foundation under the Network for Earthquake Engineering Simulation (NSF Grant No. 0936547). However, any opinions presented in this paper are solely those of the authors. In-kind support provided by Steel Fab Inc. and assistance provided by the staff of the Constructed Facilities Laboratory (CFL) at NC State University are gratefully acknowledged.
References
AISC. (1992). Seismic provisions for structural steel buildings, Chicago.
AISC. (1997). Seismic provisions for structural steel buildings, Chicago.
AISC. (2005). Steel construction manual, Chicago.
AISC. (2010a). Prequalified connections for special and intermediate steel moment frames for seismic applications, Chicago.
AISC. (2010b). Seismic provisions for structural steel buildings, Chicago.
ANSYS 14.5 [Computer software]. ANSYS, Canonsburg, PA.
ASTM. (2010). “Standard specification for general requirements for rolled structural steel bars, plates, shapes, and sheet piling.” ASTM A6-10, West Conshohocken, PA.
Bruneau, M., Uang, C. M., and Whittaker, A. (1998). Ductile design of steel structures, McGraw Hill, New York.
Chaboche, J. L. (1986). “Time-independent constitutive theories for cyclic plasticity.” Int. J. Plast., 2(2), 149–188.
Engelhardt, M. D., and Husain, A. S. (1993). “Cyclic-loading performance of welded flange-bolted web connections.” J. Struct. Eng., 3537–3550.
Engelhardt, M. D., and Sabol, T. A. (1997). “Seismic-resistant steel moment connections: Developments since the 1994 Northridge earthquake.” Prog. Struct. Engng Mater., 1(1), 68–77.
Goel, S. C., Stojadinovic, B., and Lee, H. K. (1997). “Truss analogy for steel moment connections.” Eng. J., 34(2), 43–53.
Han, S. W., Kwon, G. U., and Moon, K. H. (2007). “Cyclic behavior of Post-Northridge WUF-B connections.” J. Const. Steel Res., 63(3), 365–374.
ICBO (International Conference of Building Officials). (1988). Uniform building code, Whittier, CA.
Iwankiw, N. R., and Carter, C. J. (1996). “The dogbone: A new idea to chew on.” Modern Steel Constr., 36(4), 18–23.
Kanvinde, A. M., and Deierlein, G. G. (2007). “Cyclic void growth model to assess ductile fracture initiation in structural steels due to ultra low cycle fatigue.” J. Eng. Mech., 701–712.
Kanvinde, A. M., and Deierlein, G. G. (2008). “Validation of cyclic void growth model for fracture initiation in blunt notch and dogbone steel specimens.” J. Struct. Eng., 1528–1537.
Kaufmann, E. J., Metrovich, B. R., and Pense, A. W. (2001). “Characterization of cyclic inelastic strain behavior on properties of A572 Gr. 50 and A913 Gr. 50 rolled sections.”, National Center for Engineering Research on Advanced Technology for Large Structural Systems, Lehigh Univ., Bethlehem, PA.
Krawinkler, H., and Popov, E. P. (1982). “Seismic behavior of moment connections and joints.” J. Struct. Div., 108(2), 373–391.
Lee, C.-H., Jeon, S.-W., Kim, J.-H., and Uang, C.-M. (2005). “Effects of panel zone strength and beam web connection method on seismic performance of reduced beam section steel moment connections.” J. Struct. Eng., 1854–1865.
Lee, C.-H., and Kim, J.-H. (2007). “Seismic design of reduced beam section steel moment connections with bolted web attachment.” J. Const. Steel Res., 63(4), 522–531.
Morrison, M. L. (2015). “Innovative seismic performance enhancement techniques for steel building moment resisting connections.” Ph.D. dissertation, North Carolina State Univ., Raleigh, NC.
Morrison, M. L., Schweizer, D. Q., and Hassan, T. (2015). “An innovative seismic performance enhancement technique for steel building moment resisting connections.” J. Const. Steel Res., 109(Jun), 34–46.
Myers, A. (2009). “Testing and probabilistic simulation of ductile fracture initiation in structural steel components and weldments.” Ph.D. dissertation, Stanford Univ., Stanford, CA.
Popov, E. P., Amin, N. R., Louie, J. J. C., and Stephen, R. M. (1985). “Cyclic behavior of large beam-column assemblies.” Earthquake Spectra, 1(2), 203–238.
Popov, E. P., and Stephen, R. M. (1972). “Cyclic loading of full-size steel connections.” American Iron and Steel Institute, Washington, DC.
Popov, E. P., Yang, T., and Chang, S. (1998). “Design of steel MRF connections before and after 1994 Northridge earthquake.” Eng. Struct., 20(12), 1030–1038.
Rahman, A., Mahamid, M., Amro, A., and Ghorbanpoor, A. (2007). “The analyses of extended shear tab steel connections—Part I: The unstiffened connections.” Eng. J., 44(2), 133–146.
Richard, R. M., Jay Allen, C., and Partridge, J. E. (1997). “Proprietary slotted beam connection designs.” Modern Steel Constr., 37(3), 28–35.
Sabol, T. A., Engelhardt, M. D., Aboutaha, R. S., Frank, K. H. (1996). “An overview of the AISC Northridge moment connection test program.” Proc., 11th World Conf. on Earthquake Engineering, AISC, Chicago.
SAC. (1998). “Strength and ductility of FR welded-bolted connections.”, Richmond, CA.
SAC. (2000a). “Behavior and design of radius cut reduced beam section connections.”, Richmond, CA.
SAC. (2000b). “Failure analysis of welded beam to column connections.”, Richmond, CA.
SAC. (2000c). “Parametric tests on the free flange connections.”, Richmond, CA.
SAC. (2000d). “Parametric tests on unreinforced connections. Volume 1—Final report.”, Richmond, CA.
Stojadinović, B., Goel, S. C., Lee, K.-H., Margarian, A. G., and Choi, J.-H. (2000). “Parametric tests on unreinforced steel moment connections.” J. Struct. Eng., 40–49.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 142 • Issue 11 • November 2016
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Oct 30, 2015
Accepted: Mar 21, 2016
Published online: Jun 6, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 6, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.