Analysis and Design of Two-Tiered Steel Braced Frames under In-Plane Seismic Demand
Publication: Journal of Structural Engineering
Volume 142, Issue 11
Abstract
A seismic design strategy, which is intended to be implemented within the framework of the U.S. seismic design provisions for steel structures, is presented for single-story steel concentrically braced frames that are divided into two tiers. In this method, the columns are designed to resist the axial loads acting in combination with the in-plane flexural demand resulting from uneven distribution of brace inelastic deformations over the frame height. This design procedure, which establishes enhanced requirements beyond the 2010 edition of the U.S. seismic design provisions, prevents concentration of deformation in one tier and causes frame nonlinear deformation to be distributed between the tiers. The column bending moments depend on the story shear resistance that develops in each tier when the bracing members are at buckling and in the postbuckling range. The method also aims to control tier drifts to protect the bracing members from excessive inelastic demand, which could cause brace fracture. Nonlinear static and dynamic analyses are performed to validate the proposed design procedure.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Funding from the Natural Sciences and Engineering Research Council (NSERC) of Canada is acknowledged. The authors would like to express their thanks to Professor Ali Davaran for his most valuable assistance in the development of the numerical models used in this study.
References
Aguero, A., Izvernari, C., and Tremblay, R. (2006). “Modelling of the seismic response of concentrically braced steel frames using the OpenSees analysis environment.” Int. J. Adv. Steel Constr., 2(3), 242–274.
AISC. (2010a). “Seismic provisions for structural steel buildings.” ANSI/AISC 341-10, Chicago.
AISC. (2010b). “Specifications for structural steel buildings.” ANSI/AISC 360-10, Chicago.
AISC. (2012). Seismic design manual, 2nd Ed., Chicago.
Anderson, T. L. (1995). Fracture mechanics, 2nd Ed., CRC Press, Boca Raton, FL.
ASCE. (2010). “Minimum design loads for buildings and other structures.” SEI/ASCE 7-10, Reston, VA.
ASTM. (2007a). “Standard specification for cold-formed welded and seamless carbon steel structural tubing in rounds and shapes.” ASTM A500-07, West Conshohocken, PA.
ASTM. (2007b). “Standard specification for structural steel shapes.” ASTM A992/A 992M-07, West Conshohocken, PA.
Bruneau, M., Uang, C.-M., and Sabelli, R. (2011). Ductile design of steel structures, 2nd Ed., McGraw-Hill Professional, New York, 928.
Chen, C.-H., and Mahin, S. (2010). “Seismic collapse performance of concentrically steel braced frames.” Proc., ASCE Structures Congress 2010, ASCE, Reston, VA, 1265–1274.
Dalal, S. T. (1969). “Some non-conventional cases of column design.” Eng. J. AISC, 6(1), 28–39.
Davaran, A. (2001). “Effective length factor for discontinuous X-bracing systems.” J. Eng. Mech., 106–112.
Davaran, A., Gélinas, A., and Tremblay, R. (2014). “Inelastic buckling analysis of steel X-bracing with bolted single shear lap connections.” J. Struct. Eng., 04014204.
Davaran, A., and Hoveidae, N. (2009). “Effect of mid-connection detail on the behavior of X-bracing systems.” J. Constr. Steel Res., 65(4), 985–990.
Dexter, R. J., Graeser, M., Saari, W. K., Pascoe, C., Gardner, C. A., and Galambos, T. V. (2000). “Structural shape material property survey.”, Univ. of Minnesota, Minneapolis.
Fell, B. V., Kanvinde, A. M., Deierlein, G. G., and Myers, A. T. (2009). “Experimental investigation of inelastic cyclic buckling and fracture of steel braces.” J. Struct. Eng., 19–32.
FEMA. (2009). “Quantification of building seismic performance factors.” Applied Technology Council, FEMA P695, Redwood City, CA.
Filiatrault, A., Tremblay, R., Christopoulos, C., Folz, B., and Pettinga, D. (2013). Elements of earthquake engineering and structural dynamics, 3rd Ed., Presses Internationales Polytechnique, Montreal, 874.
Galambos, T. V., and Ketter, R. L. (1958). “Columns under combined bending and thrust.”, Fritz Engineering Laboratory, Bethlehem, PA.
Hsiao, P.-C., Lehman, D. E., and Roeder, C. W. (2013). “A model to simulate special concentrically braced frames beyond brace fracture.” Earthquake Eng. Struct. Dyn., 42(2), 183–200.
Imanpour, A., Stoakes, C., Tremblay, R., Fahnestock, L., and Davaran, A. (2013). “Seismic stability response of columns in multi-tiered braced steel frames for industrial applications.” Proc., ASCE Structures Congress, ASCE, Reston, VA, 2650–2661.
Imanpour, A., and Tremblay, R. (2014). “Seismic design of steel multi-tiered braced frames: Application of incremental static analysis for design of steel multi-tiered braced frames.” Proc., Int. European Conf. on Steel and Composite Structures, Eurosteel 2014, Dept. of Structures for Engineering and Architecture, Univ. of Naples Federico II, Naples, Italy.
Imanpour, A., Tremblay, R., Davaran, A., Stoakes, C., and Fahnestock, L. (2016). “Seismic performance assessment of multi-tiered steel concentrically braced frames designed in accordance with 2010 AISC seismic provisions.” J. Struct. Eng., in press.
Lamarche, C. P., and Tremblay, R., (2011). “Seismically induced cyclic buckling of steel columns including residual-stress and strain-rate effects.” J. Constr. Steel Res., 67(9), 1401–1410.
MacRae, G. A., Kimura, Y., and Roeder, C. (2004). “Effect of column stiffness on braced frame seismic behavior.” J. Struct. Eng., 381–391.
McKenna, F., and Fenves, G. L. (2004). “Open system for earthquake engineering simulation (OpenSees).” 〈http://opensees.berkeley.edu/〉.
Moreau, R., Rogers, C. A., and Tremblay, R. (2014). “Inelastic performance of the “Modified-hidden-gap” connection for square HSS brace members.” Proc., 10th National Earthquake Engineering Conf., Earthquake Engineering Research Institute (EERI), Oakland, CA.
Palmer, K. D., Roeder, C. W., Lehman, D. E., Okazaki, T., Shield, C. K., and Powell, J. (2012). “Concentric X-braced frames with HSS bracing.” Int. J. Steel Struct., 12(3), 443–459.
Qu, B., Sanchez-Zamora, F., and Pollino, M. (2015). “Transforming seismic performance of deficient steel concentrically braced frames through implementation of rocking cores.” J. Struct. Eng., 04014139.
Rao, N. R. M., Lohrmann, M., and Tall, L. (1966). “Effects of strain rate on the yield stress of structural steels.” J. Mater., 1(3), 238–248.
Roeder, C. W. (2011). “Influence of Gusset plate connection and braces on the seismic performance of X-braced frames.” Earthquake Eng. Struct. Dyn., 40(4), 355–374.
Schmidt, B. J., and Bartlett, F. M. (2002). “Review of resistance factor for steel: Data collection.” Can. J. Civ. Eng., 29(1), 109–118.
Simão, P. D., Girão Coelho, A. M., and Bijlaard, F. S. K. (2012). “Stability design of crane columns in mill buildings.” Eng. Struct., 42, 51–82.
Stoakes, C., and Fahnestock, L. (2012). “Influence of weak-axis flexural yielding on strong-axis buckling strength of wide flange columns.” Proc., Annual Stability Conf., Structural Stability Research Council, Grapevine, TX.
Stoakes, C., and Fahnestock, L. (2016). “Strong-axis stability of wide flange steel columns in the presence of weak-axis flexure.” J. Struct. Eng., 04016004.
Tremblay, R. (2002). “Inelastic seismic response of steel bracing members.” J. Constr. Steel Res., 58(5-8), 665–701.
Tremblay, R. (2003). “Achieving a stable inelastic seismic response for concentrically braced steel frames.” Eng. J., AISC, 40(2), 111–129.
Tremblay, R., Archambault, M. H., and Filiatrault, A. (2003). “Seismic performance of concentrically braced steel frames made with rectangular hollow bracing members.” J. Struct. Eng., 1626–1636.
Tremblay, R., and Filiatrault, A. (1996). “Seismic impact loading in inelastic tension-only concentrically braced frames: Myth or reality?” Earthquake Eng. Struct. Dyn., 25(12), 1373–1389.
Uriz, P., Filippou, F. C., and Mahin, S. A. (2008). “Model for cyclic inelastic buckling of steel braces.” J. Struct. Eng., 619–628.
Uriz, P., and Mahin, S. (2008). “Toward earthquake-resistant design of concentrically braced steel-frame structures.”, Pacific Earthquake Engineering Research Center, Univ. of California, Berkeley, CA.
Yang, F., and Mahin, S. (2005). Limiting net section fracture in slotted tube braces, SteelTIPS, Technical Information and Product Service, Structural Steel Educational Council, Moraga, CA.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Nov 2, 2014
Accepted: Mar 18, 2016
Published online: Jun 27, 2016
Published in print: Nov 1, 2016
Discussion open until: Nov 27, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.