Abstract
This paper summarizes a number of key findings that affect the use of linear and nonlinear analysis procedures for the seismic evaluation of steel frame buildings with supplemental damping devices and in particular, buckling-restrained braces (BRBs) and nonlinear viscous dampers (NVDs). The assessment is based on a comparison of various engineering demand parameters (EDPs) with experimental data obtained from a series of full-scale shaking table tests of a five-story steel building equipped with BRBs and NVDs. It is shown that: (1) there is no clear advantage between three-dimensional (3D) and two-dimensional (2D) analyses in the prediction of the dynamic behavior of regular plan view steel frame buildings regardless of the damper type; (2) incorporating the brace and nonlinear viscous damper axial flexibility in the analytical model of the test structure with NVDs significantly improves the overall numerical predictions; and (3) the current effective damping ratio recommended by ASCE 41-13 as part of linear static procedures for the evaluation of frame buildings with BRBs or NVDs may not be conservative enough. A new performance-based design tool called performance-spectra (P-Spectra) is able to reliably predict the EDPs of interest. The P-Spectra tool is also able to validate the efficiency of various damper solutions on the dynamic performance of the test structure. It is demonstrated that P-Spectra can be employed to predict estimates of potential residual deformations that traditional linear and nonlinear static procedures cannot.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors express their sincere thanks to the research team who conducted the test and to the National Research Institute for Earth Science and Disaster Prevention for providing the experimental data for the needs of this paper. The Financial support from Fonds de recherche du Québec Nature et technologies (Grant No. 2013—NC-166845) for the doctoral studies of the first author at McGill University is also acknowledged.
References
AISC. (2010). “Specification for structural steel buildings.” ANSI/AISC 360-10, Chicago.
Akcelyan, S., Lignos, D. G., and Hikino, T. (2015). “Adaptive numerical method algorithms for nonlinear viscous and bilinear oil damper models under random vibrations.” J. Eng. Mech., in press.
ASCE. (2010). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-10, Reston, VA.
ASCE/SEI (Structural Engineering Institute). (2014). “Seismic evaluation and retrofit of existing buildings.” ASCE/SEI 41-13, Reston, VA.
BCJ (Building Center of Japan). (2008). “Seismic provisions for design of building structures.” Tokyo.
Buchanan, A., Bull, D., Dhakal, R., MacRae, G., Palermo, A., and Pampanin, S. (2011). “Base isolation and damage-resistant technologies for improved seismic performance of buildings: A report written for the Royal Commission of Inquiry into building failure caused by the Canterbury earthquakes.”, Dept. of Civil and Natural Resources Engineering, Univ. of Canterbury, Christchurch, U.K.
Chopra, A. K., and Goel, R. K. (2001). “A modal pushover analysis procedure for estimating seismic demands for buildings.” Pacific Earthquake Engineering Research Center, Berkeley, CA.
Christopoulos, C., and Filiatrault, A. (2006). Principles of supplemental damping and seismic isolation, IUSS Press, Milan, Italy.
Cimellaro, G. P., Reinhorn, A. M., and Bruneau, M. (2010). “Framework for analytical quantification of disaster resilience.” Eng. Struct., 32(11), 3639–3649.
Constantinou, M. C., and Symans, M. D. (1993). “Seismic response of the structures with supplemental damping.” Struct. Des. Tall Build., 2(2), 77–92.
Dao, N. D., Ryan, K. L., Sato, E., and Sasaki, T. (2013). “Predicting the displacement of triple pendulum™ bearings in a full-scale shaking experiment using a three-dimensional element.” Earthquake Eng. Struct. Dyn., 42(11), 1677–1695.
Dhakal, R. P., MacRae, G. A., and Hogg, K. (2011). “Performance of ceilings in the February 2011 Christchurch earthquake.” Bull. N. Z. Soc. Earthquake Eng., 44(4), 379–389.
Dormand, J. R., and Prince, P. J. (1980). “A family of embedded Runge-Kutta formulae.” J. Comput. Appl. Math., 6(1), 19–26.
E-Defense. (2008). “2008 blind analysis contest by E-Defense.” Hyogo Earthquake Engineering Research Center, 〈http://www.bosai.go.jp/hyogo/blind-analysis/2008/eng/outline/outline.html〉 (Dec. 5, 2008).
Fahnestock, L., Ricles, J., and Sause, R. (2007). “Experimental evaluation of a large-scale buckling-restrained braced frame.” J. Struct. Eng., 1205–1214.
FEMA. (1997). “NEHRP provisions for the seismic rehabilitation of buildings.”, Washington, DC.
FEMA. (2000). “Prestandard and commentary for the seismic rehabilitation of buildings.”, Washington, DC.
FEMA. (2005). “Improvement of nonlinear static seismic analysis procedures.”, Washington, DC.
FEMA. (2012). “Seismic performance assessment of buildings.”, Washington, DC.
Folz, B., and Filiatrault, A. (2001). “SAWS—Version 1.0, A computer program for the seismic analysis of woodframe structures.”, Dept. of Structural Engineering, Univ. of California, San Diego.
Guo, J. W. W., and Christopoulos, C. (2013a). “A procedure for generating performance spectra for structures equipped with passive supplemental dampers.” Earthquake Eng. Struct. Dyn., 42(9), 1321–1338.
Guo, J. W. W., and Christopoulos, C. (2013b). “Performance spectra based method for the seismic design of structures equipped with passive supplemental damping systems.” Earthquake Eng. Struct. Dyn., 42(6), 935–952.
Hikino, T. (2012). “Full-scale shaking table test and analysis of the dynamic characteristics verification that govern the seismic behavior of steel buildings with supplemental damping.” Ph.D. dissertation, Kyoto Univ., Japan (in Japanese).
Ji, X., Hikino, T., Kasai, K., and Nakashima, M. (2013). “Damping identification of a full-scale passively controlled five-story steel building structure.” Earthquake Eng. Struct. Dyn., 42(2), 277–295.
JSSI (Japan Society of Seismic Isolation). (2005). Manual for design and construction of passively-controlled buildings, 2nd Ed., Tokyo (in Japanese).
Kasai, K., et al. (2008). “Value-added 5-story steel frame and its components: Part 1—Full-scale damper tests and analyses.” Proc., 14th World Conf. on Earthquake Engineering, Beijing.
Kasai, K., et al. (2010). “Full-scale shake table tests of 5-story steel building with various dampers.” Proc., 7th Int. Conf. on Urban Earthquake Engineering (7CUEE) and 5th Int. Conf. on Earthquake Engineering (ICEE), Tokyo Institute of Technology, Tokyo.
Kasai, K., Fu, Y., and Watanabe, A. (1998). “Passive control systems for seismic damage mitigation.” J. Struct. Eng., 501–512.
Kasai, K., and Ito, H. (2005). “Passive control design method based on tuning of stiffness, yield strength, and ductility of elasto-plastic damper.” J. Struct. Constr. Eng., 70(595), 45–55 (in Japanese).
Kasai, K., Mita, A., Kitamura, H., Matsuda, K., Morgan, T. A., and Taylor, A. W. (2013). “Performance of seismic protection technologies during the 2011 Tohoku-Oki earthquake.” Earthquake Spectra, 29(S1), S265–S293.
Kasai, K., Murata, S., Kato, F., Hikino, T., and Ooki, Y. (2011). “Evaluation rule for vibration period, damping, and mode vector of buildings tested by a shake table with inevitable rocking motions.” J. Struct. Constr. Eng., 76(670), 2031–2040 (in Japanese).
Kasai, K., Ogura, T., and Suzuki, A. (2007). “Passive control design method based on tuning equivalent stiffness of nonlinear viscous dampers.” J. Struct. Constr. Eng., 73(618), 97–104 (in Japanese).
Krawinkler, H. (1978). “Shear in beam-column joints in seismic design of steel frames.” Eng. J., 15(3), 82–91.
Lai, M., Chang, K., Soong, T., Hao, D., and Yeh, Y. (1995). “Full-scale viscoelastically damped steel frame.” J. Struct. Eng., 1443–1447.
Lignos, D., Hikino, T., Matsuoka, Y., and Nakashima, M. (2013). “Collapse assessment of steel moment frames based on E-defense full-scale shake table collapse tests.” J. Struct. Eng., 120–132.
Lignos, D., Putman, C., Zareian, F., and Krawinkler, H. (2011). “Seismic evaluation of steel moment frames and shear walls using nonlinear static analysis procedures.” Proc., Structures Congress 2011, ASCE, Reston, VA, 2204–2215.
Lignos, D. G. (2010). “Interactive interface for incremental dynamic analysis: Theory and example applications manual, version 1.1.5.” Dept. of Civil Engineering and Applied Mechanics, McGill Univ., Montreal.
Lignos, D. G. (2012). “Modeling and experimental validation of a full scale 5-story steel building equipped with triple friction pendulum bearings: E-defense blind analysis competition.” Proc., 9th Int. Conf. on Urban Earthquake Engineering (9CUEE) and 4th Asia Conf. on Earthquake Engineering, Center for Urban Earthquake Engineering (CUEE), Tokyo Institute of Technology, Tokyo.
Lignos, D. G., Putman, C., and Krawinkler, H. (2015). “Application of simplified analysis procedures for performance-based earthquake evaluation of steel special moment frames.” Earthquake Spectra, 31(4), 1949–1968.
Maison, B. F., Kasai, K., and Deierlein, G. (2009). “ASCE-41 and FEMA-351 evaluation of E-defense collapse test.” Earthquake Spectra, 25(4), 927–953.
Makris, N., and Constantinou, M. (1991). “Fractional-derivative Maxwell model for viscous dampers.” J. Struct. Eng., 2708–2724.
McKenna, F. T. (1997). “Object-oriented finite element programming: Frameworks for analysis, algorithms and parallel computing.” Ph.D. dissertation, Univ. of California, Berkeley, CA.
Menegotto, M., and Pinto, P. E. (1973). “Method of analysis for cyclically loaded reinforced concrete plane frames including changes in geometry and non-elastic behaviour of elements under combined normal force and bending.” Proc., IABSE Symp. on Resistance and Ultimate Deformability of Structures Acted on by Well Defined Repeated Loads, IABSE-AIPC-IVBH, ETH Zürich, Zürich, Switzerland, 15–22.
Miranda, E., Mosqueda, G., Retamales, R., and Pekcan, G. (2012). “Performance of nonstructural components during the 27 February 2010 Chile earthquake.” Earthquake Spectra, 28(S1), S453–S471.
Newmark, N. M. (1959). “A method of computation for structural dynamics.” J. Eng. Mech. Div., 85(3), 67–94.
NIST. (2010). “Evaluation of the FEMA P695 methodology for quantification of building seismic performance factors.” NEHRP Consultants Joint Venture, Gaithersburg, MD.
OpenSees 2.4.4 [Computer software]. Pacific Earthquake Engineering Research Center (PEER), Univ. of California, Berkeley, CA.
Ramirez, C. M., and Miranda, E. (2012). “Significance of residual drifts in building earthquake loss estimation.” Earthquake Eng. Struct. Dyn., 41(11), 1477–1493.
Ramirez, O. M., et al. (2001). “Development and evaluation of simplified procedures for analysis and design of buildings with passive energy dissipation systems.”, Multidisciplinary Center for Earthquake Engineering Research, Univ. of Buffalo, Buffalo, NY.
SAP2000 14.2.4 [Computer software]. Computer and Structures Inc., Berkeley, CA.
Wen, Y. K. (1976). “Method for random vibration of hysteretic systems.” J. Eng. Mech., 102(2), 249–263.
Yamashita, T., Kawabata, J., Ninomiya, M., Sakaba, N., and Yanagawa, Y. (2010). “2- and 3-D blind analyses of full-scale 5-story building with viscous dampers.” Proc., 7th Int. Conf. on Urban Earthquake Engineering (7CUEE) and 5th Int. Conf. on Earthquake Engineering (5ICEE), Tokyo Institute of Technology, Tokyo.
Yassin, M. H. M. (1994). “Nonlinear analysis of prestressed concrete structures under monotonic and cycling loads.” Ph.D. dissertation, Univ. of California, Berkeley, CA.
Yu, Y., Tsai, K., Li, C., Weng, Y., and Tsai, C. (2013). “Earthquake response analyses of a full-scale five-story steel frame equipped with two types of dampers.” Earthquake Eng. Struct. Dyn., 42(9), 1301–1320.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Apr 3, 2015
Accepted: Nov 17, 2015
Published online: Feb 4, 2016
Published in print: Jun 1, 2016
Discussion open until: Jul 4, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.