Contribution of Type-X Gypsum Wall Board to the Racking Performance of Light-Frame Wood Shear Walls
Publication: Journal of Structural Engineering
Volume 142, Issue 5
Abstract
This paper presents an experimental investigation of the racking performance of light-frame wood shear walls to evaluate the effect of Type X gypsum wall board (GWB). Twelve shear walls sheathed with oriented strand board (OSB) alone, GWB alone, or in combination were tested under static monotonic or reversed cyclic lateral load. The racking performance of these wall specimens in terms of stiffness, strength, ultimate displacement, ductility, energy dissipation, and failure modes was investigated. Specifically the effects of panel orientation, GWB panel joint taping, and double-layer GWB were examined. It was found that shear walls sheathed with GWB provide ductility ratios similar to or higher than those of OSB sheathed walls. The direct superposition rule can be applied to estimate the overall strength of a shear wall sheathed with single-layer OSB and GWB on opposite faces, provided there is no panel joint taping and the panel orientation is the same for both materials. The superposition rule proposed in current United States standards provides a conservative estimate for other cases considered in this study. In addition, shear walls with two GWB panels jointed by taping and double-layer GWB panels behaved like shear walls sheathed with a single large-size panel, leading to a reduction in the system ductility ratio and corresponding seismic force modification factor. This test series have provided essential test data for future modeling work to investigate the seismic response analysis of light wood-frame buildings containing Type X GWB.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors greatly acknowledge the financial support provided by Natural Sciences and Engineering Research Council (NSERC) of Canada under the Strategic Research Network on Innovative Wood Products and Building Systems (NEWBuildS). The technical advice from Dr. Chun Ni and Dr. Mohammad Mohammad from FPInnovations have contributed greatly to this study.
References
Asiz, A., Chui, Y. H., Doudak, G., Ni, C., and Mohammad, M. (2011). “Contribution of plasterboard finished to structural performance of multi-storey light wood frame buildings.” Procedia Eng., 14, 1572–1581.
ASTM. (2011). “Standard test methods for cyclic (reversed) load test for shear resistance of framed walls for buildings.” ASTM E2126, West Conshohocken, PA.
ASTM. (2012). “Standard practice for static load test for shear resistance of framed walls for buildings.” ASTM E564, West Conshohocken, PA.
ASTM. (2013). “Standard specification for application and finishing of gypsum board.” ASTM C840, West Conshohocken, PA.
CSA (Canadian Standards Association). (2014). “Engineering design in wood.” CSA O86-14, Toronto.
FEMA. (2012). “Seismic evaluation and retrofit of multi-unit wood-frame buildings with weak first stories.”, Applied Technology Council, Washington, DC.
Filiatrault, A., Fischer, D., Folz, B., and Uang, C. M. (2002). “Seismic testing of two-storey woodframe house: Influence of wall finish materials.” J. Struct. Eng., 1337–1345.
Karacabeyli, E., and Ceccotti, A. (1996). “Test results on the lateral resistance of nailed shear walls.” Proc., Int. Wood Engineering Conf., 2, 179–186.
McMullin, K. M., and Merrick, D. (2001). “Seismic performance of gypsum walls–experimental test program.” Proc., Workshop 15, Consortium of Univ. Research in Earthquake Engineering, Richmond, VA, 19.
Memari, A. M., Kasal, B., Manbeck, H. B., and Adams, A. R. (2009). “Lateral load resistance evaluation of wood- and steel-stud partition shear walls.” J. Archit. Eng., 122–130.
Memari, A. M., and Solnosky, R. L. (2014). “In-plane shear performance of wood-framed drywall sheathing wall systems under cyclic racking loading.” Open J. Civ. Eng., 4(1), 54–70.
Newmark, N. M., and Hall, W. J. (1982). “Earthquake spectra and design.”, Earthquake Engineering Research Institute, Berkeley, CA.
NRCC (National Research Council of Canada). (2010). “National building code of Canada.” Canadian Commission on Building and Fire Codes and NRCC, Ottawa.
Paevere, P. (2002). “Full-scale testing, modeling and analysis of light-frame structures under lateral loading.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Melbourne, Melbourne, Australia.
Park, R. (1989). “Evaluation of ductility of structures and structural assemblages from laboratory testing.” Bull. New Zealand Nat. Soc. Earthquake Eng., 22(3), 155–166.
Rodriguez-Nikl, T., Gupta, R., Kramer, A., and Sinha, A. (2014). “Seismic laboratory testing of energy-efficient, staggered-stud, wood-frame shear walls.” J. Struct. Eng., B4014003.
Sinha, A., and Gupta, R. (2009). “Strain distribution in OSB and GWB in wood-frame shear walls.” J. Struct. Eng., 666–675.
Uang, C. M., and Gatto, K. (2003). “Effects of finish materials and dynamic loading on the cyclic response of woodframe shearwalls.” J. Struct. Eng., 1394–1402.
van de Lindt, J., and Liu, H. (2007). “Nonstructural elements in performance-based seismic design of wood frame structures.” J. Struct. Eng., 432–439.
Wolfe, R. W. (1983). “Contribution of gypsum wallboard to racking resistance of light-frame walls.”, U.S. Dept. of Agriculture, Madison, WI.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Feb 24, 2015
Accepted: Nov 3, 2015
Published online: Jan 11, 2016
Published in print: May 1, 2016
Discussion open until: Jun 11, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.