Effect of Surface Roughness on Cyclic Ductility of Corroded Steel
Publication: Journal of Structural Engineering
Volume 142, Issue 6
Abstract
Stable cyclic hysteretic behavior is required from structural members to dissipate seismic energy. Limited knowledge exists on the hysteretic behavior of corroded steel, and a relationship that quantifies energy dissipation capacity as a function of section thickness and roughness does not exist. Monotonic and cyclic tests of corroded steel were conducted in this research in an attempt to provide such quantification. Results from coupons suggest that assessing the strength of rusted members by machining a smooth coupon from steel extracted from an existing corroded structure, and only using the resulting yield and ultimate strength values in otherwise standard multilinear monotonic models, may be an unconservative approach. Results from cycling tests show that: (1) rusted steel can exhibit a significant hysteretic energy capacity, (2) a linear relationship exists between the total dissipated energy normalized by mean thickness and the mean 10-point-height of irregularities, and (3) increases in roughness correspond to decreases in the magnitude of total normalized energy dissipated before complete failure.
Get full access to this article
View all available purchase options and get full access to this article.
References
AISC. (1953). “Iron and steel beams–1873 to 1952 (AISC).” Chicago.
AISC. (2010). “AISC 341-10, seismic provisions.” Chicago.
Albrecht, P., and Simon, S. (1981). “Fatigue notch factors for structural details.” J. Struct. Eng., 107(7), 1279–1296.
ANSYS [Computer software]. ANSYS Incorporated, Canonsburg, PA.
ASTM. (1991). “Standard test methods of tension testing metallic materials.” ASTM E8-91, West Conshohocken, PA.
ASTM. (1999). “Standard practice for preparing, cleaning and evaluating corrosion test specimens.” ASTM G1-90, West Conshohocken, PA.
Bill, R. C. (1982). “A review of factors that influence fretting wear, in materials evaluation under fretting conditions.”, ASTM, West Conshohocken, PA, 178–179.
Bruneau, M., Uang, C. M., and Sabelli, R. (2011). Ductile design of steel structures, 2nd Ed., McGraw-Hill, New York, 921.
Bruneau, M., and Zahrai, S. (1998). “Some observations on the effect of severe corrosion on cyclic ductility of steel.” Ottawa-Carleton Earthquake Engineering Research Center, Ottawa.
Burke, S. (2002). “An experimental study on the non-destructive evaluation of corroded bridge steel.” M.Sc. thesis, Dept. of Civil Engineering, Univ. of Ottawa, Ottawa.
Burke, S. J., and Bruneau, M. (2002). “An experimental study on the non-destructive evaluation of corroded bridge steel.”, Ottawa-Carleton Earthquake Engineering Research Center, Univ. of Ottawa, Ottawa, Canada, 298.
Fisher, J. W., Yen, B. T., and Wang, D. (1991). “Corrosion and its influence on strength of steel bridge members.” Transp. Res. Rec., 1290, 211–219.
Fitgerald, R. W. (1967). Strength of materials, Don Mills, Canada, 306–307.
Gucuyen, E., and Erdem, R. T. (2014). “Corrosion effects on structural behaviour of jacket type offshore structures.” Građevinar, 66(11), 981–986.
Kayser, J. R., Malinski, T., and Nowak, A. S. (1987). “Corrosion damage models for steel girder bridges.” Proc., Effects of Damage and Redundancy on Structural Performance, ASCE, Reston, VA, 9–22.
Kayser, J. R., and Nowak, A. S. (1989). “Capacity loss due to corrosion in steel-girder bridges.” J. Struct. Eng., 1525–1537.
Kulicki, J. M., Prucz, Z., Sorgenfrei, D. F., Mertz, D. R., and Young, W. T. (1990). “Guidelines for evaluating corrosion effects in existing steel bridges.”, Transportation Research Board, National Research Council, Washington, DC.
Nakai, T., Matsushita, H., and Yamamoto, N. (2005). “Effect of pitting corrosion on local strength of hold frames of bulk carriers (2nd Report)—Lateral-distortional buckling and local face buckling.” Mar. Struct., 17(8), 612–641.
Nakai, T., Matsushita, H., and Yamamoto, N. (2006). “Effect of pitting corrosion on strength of web plates subjected to patch loading.” Thin-Walled Struct., 44(1), 10–19.
Paik, J. K., Lee, J. M., and Ko, M. J. (2004). “Ultimate shear strength of plate elements with pit corrosion wastage.” Thin-Walled Struct., 42(8), 1161–1176.
Rajabipour, A., and Melchers, R. E. (2013). “A numerical study of damage caused by combined pitting corrosion and axial stress in steel pipes.” Corros. Sci., 76, 292–301.
Testex Corporation. (1999). “Burnishing tool and replica tape.” Newark.
Yu, W., Karr, D. G., and Vargas, P. M. (2012). “Corrosion effects on reliability of flat plates in tension.” J. Offshore Mech. Arct. Eng., 134(2), 021404.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Dec 21, 2014
Accepted: Aug 25, 2015
Published online: Jan 19, 2016
Published in print: Jun 1, 2016
Discussion open until: Jun 19, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.