Experimental Study and Numerical Investigation of Blockhaus Shear Walls Subjected to In-Plane Seismic Loads
Publication: Journal of Structural Engineering
Volume 141, Issue 4
Abstract
Blockhaus systems represent a traditional construction technology in which structural resistance is obtained by direct contact between multiple timber surfaces obtained through carvings, notches, and ancient joints. Native of forested areas, this technology is currently used for the construction of log buildings also in earthquake-prone areas. Their seismic structural behavior hence represents an interesting and not well known research topic. In the paper, experimental results obtained by cyclic and monotonic tests recently performed on Blockhaus shear walls with three different types of joints are presented and discussed. At the same time, sophisticated finite-element numerical models able to take into account the complex structural behavior of log-walls subjected to in-plane seismic forces are described. Performed numerical simulations highlighted that in general multiple factors affect the global structural response of Blockhaus shear walls, including the presence of imperfections (small gaps) in the joints, the contribution of friction phenomena, the mechanical properties of timber, and the interaction between in-plane seismic forces and vertical permanent loads. However, careful calibration of timber mechanical properties and contact interactions between overlapping logs can provide accurate numerical predictions and good correlation with full-scale experimental results.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Rubner Haus AG SpA is gratefully acknowledged for funding the research project. Dr. Annalisa Battisti is also acknowledged for her cooperation during the experimental and modeling phase. Dr. Andrea Polastri [CNR IVALSA Trees and Timber Institute, San Michele all’Adige (Italy)] is acknowledged for the technical support provided during the full-scale experiments performed on Blockhaus shear walls. Dr. Franco Trevisan [University of Trieste, DICAR—Department of Engineering and Architecture, Trieste (Italy)] is finally acknowledged for his technical support for the friction and compressive experiments performed on small Blockhaus components.
References
Bedon, C., Fragiacomo, M., Amadio, C., and Sadoch, C. (2013). “Experimental and numerical investigation of ’Blockhaus’ shear walls under in-plane cyclic loads.” Proc., XV ANIDIS Conf. (CD-ROM), Padua, Italy.
Branco, J., and Araújo, J. P. (2010). “Lateral resistance of log timber walls subjected to horizontal loads.” Proc., of WCTE 2010 (CD-ROM).
Branco, J., and Araújo, J. P. (2012). “Structural behaviour of log timber walls under lateral in-plane loads.” Eng. Struct., 40, 371–382.
Ceccotti, A., Sandhaas, C., Okabe, M., Yasumura, M., Minowa, C., and Kawai, N. (2013). “SOFIE project—3D shaking table test on a seven-storey full-scale cross-laminated timber building.” Earthquake Eng. Struct. Dyn., 42(13), 2003–2021.
European Committee for Standardization (CEN). (2004a). “Eurocode 3—Design of steel structures—Part 1-1: General rules and rules for buildings.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2004b). “Eurocode 8—Design of structures for earthquake resistance—Part 1: General rules, seismic actions and rules for buildings.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2006a). “Adhesives, phenolic and aminoplastic, for load-bearing timber structures—Classification and performance requirements.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2006b). “Timber structures—Test methods—Cyclic testing of joints made with mechanical fasteners.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2009a). “Eurocode 5—Design of timber structures—Part 1-1: General-common rules and rules for buildings.”, Brussels, Belgium.
European Committee for Standardization (CEN). (2009b). “Structural timber-strength classes.”, CEN European Committee for Standardization, Brussels, Belgium.
Gavric, I., Fragiacomo, M., Popovski, M., and Ceccotti, A. (2014). “Behaviour of cross-laminated timber panels under cyclic loads.” Mater. Joints Timber Struct., 9, 689–702.
Hirai, T., Kimura, T., Yanaga, K., Sasaki, Y., and Koizumi, A. (2004). “Lateral resistance of log constructions.” Proc. of WCTE 2004 (CD-ROM), Vol. 1.
Pang, S. J., Ok, J. K., Park, J. S., Park, C. Y., and Lee, J. J. (2011). “Moment-carrying capacity of dovetailed mortise and tenon joints with or without beam shoulder.” J. Struct. Eng., 785–789.
Parida, G., Fragiacomo, M., and Johnsson, H. (2013). “Prefabricated timber walls anchored with glued-in rod connections: Racking tests and preliminary design.” Eur. J. Wood Wood Prod., 71(5), 635–646.
Simulia ABAQUS v.6.12 [Computer software]. Providence, RI, Dassault Systems.
Tannert, T., Lam, F., and Vallée, T. (2010). “Strength prediction for rounded dovetail connections considering size effects.” J. Eng. Mech., 358–366.
Tomasi, R., Sartori, T., Grossi, P., and Wenzel, L. (2012). “Sistema costruttivo Blockhaus: prove su giunzioni d’angolo.” Internal Rep., Univ. of Trento, Italy (in italian).
Van de Lindt, J. W. (2004). “Evolution of wood shear wall testing, modeling and reliability analysis: Bibliography.” Pract. Period. Struct. Des. Constr., 44–53.
Van de Lindt, J. W., Pei, S., and Pryor, S. E. (2011). “Construction and experimental seismic performance of a full-scale six-story light-frame wood building.” Procedia Eng., 14, 1599–1605.
Vasconcelos, G., Poletti, E., Salavessa, E., Jesus, A. M. P., Lourenço, P. B., Pilaon, P. (2013). “In-plane shear behaviour of traditional timber walls.” Eng. Struct., 56, 1028–1048.
Vogt, T., Hummel, J., and Seim, W. (2012). “Timber framed wall elements under cyclic loading.” Proc. WCTE-World Conf. on Timber Engineering (CD-ROM), Auckland.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Nov 19, 2013
Accepted: Feb 25, 2014
Published online: Jul 9, 2014
Discussion open until: Dec 9, 2014
Published in print: Apr 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.