Seismic Performance of High-Strength Self-Compacting Concrete in Reinforced Concrete Beam-Column Joints
Publication: Journal of Structural Engineering
Volume 140, Issue 5
Abstract
Because of its potentially beneficial properties, there has been an increased interest in recent years on performance of self-compacting concrete (SCC) in structural members. The capability of SCC in flowing through and filling in even the most congested areas makes it ideal for use in congested reinforced concrete (RC) structural members such as beam-column joints (BCJ). However, members of tall multistory structures impose high capacity requirements where implementing normal-strength self-compacting concrete (NSSCC) is not preferable. In the present study, six beam-column joint specimens were designed following the guidelines of the New Zealand concrete standards; namely, three high-strength self-compacting concrete (HSSCC), one conventionally vibrated high-strength concrete (CVHSC), one conventionally vibrated concrete (CVC), and one CVC with HSSCC in its joint region. Factors such as the concrete type (HSSCC, CVHSC, and CVC), amount of joint shear stirrups, axial load ratio (1% and 10% of section capacity), and direction of casting were considered as variables in designing these specimens. All BCJs were tested under a displacement-controlled quasi-static reversed cyclic loading regime. Seismically important features such as shear force, drift ratio, member deformations, strains, crack pattern, and crack width were measured; and damping, stiffness, joint shear stress, contribution of different components, and elongation of plastic hinge zone were calculated. Joint shear stresses were varied from 6 to 7 MPa; yet within the maximum code limit of about 10 MPa. It was found that not only none of the seismically important features were compromised by using HSSCC, but also the quality of material and ease of construction boosted the performance of beam-column subassemblies.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors would like to acknowledge the funding provided for the project by the Earthquake Commission (EQC) New Zealand, the University of Canterbury, and the Department of Civil and Natural Resources Engineering. Authors would like to extend their sincere thanks to James Mackechnie, SI Plant Engineer at Allied Concrete, and Tim Perigo, technician of the structures laboratory at the University of Canterbury, for their continuous support throughout the experimental stage of this study. Without their diligent efforts and high-quality inputs, fabrication and testing of the beam-column subassemblies would have become a much more tedious task.
References
American Concrete Institute (ACI). (2005). “Acceptance criteria for moment frames based on structural testing and commentary.”, Detroit.
American Concrete Institute (ACI). (2008). “Building code requirements for structural concrete and commentary.”, Detroit.
De Almeida Filho, F. M., El Debs, M. K., and El Debs, A. L. H. C. (2008). “Bond-slip behavior of self-compacting concrete and vibrated concrete using pull-out and beam tests.” Mater. Struct., 41(6), 1073–1089.
Desnerck, P., De Schutter, G., and Taerwe, L. (2010). “Bond behaviour of reinforcing bars in self-compacting concrete: Experimental determination by using beam tests.” Mater. Struct., 43, 53–62.
Domone, P. L. (2006). “Self-compacting concrete: An analysis of 11 years of case studies.” Cement Concr. Compos., 28(2), 197–208.
Hassan, A. A. A., Hossain, K. M. A., and Lachemi, M. (2008). “Behavior of full-scale self-consolidating concrete beams in shear.” Cement Concr. Compos., 30(7), 588–596.
Hwang, S.-D., Khayat, K. H., and Bonneau, O. (2006). “Performance-based specifications of self-consolidating concrete used in structural applications.” ACI Mater. J., 103(2), 121–129.
Kim, Y. H., Hueste, M. B. D., Trejo, D., and Cline, D. B. H. (2010). “Shear characteristics and design for high-strength self-consolidating concrete.” J. Struct. Eng., 989–1000.
Lachemi, M., Hossain, K. M. A., and Lambros, V. (2005). “Shear resistance of self-consolidating concrete beams—Experimental investigations.” Can. J. Civ. Eng., 32(6), 1103–1113.
Peng, B., Dhakal, R., Fenwick, R., Carr, A., and Bull, D. (2013). “Multispring hinge element for reinforced concrete frame analysis.” J. Struct. Eng., 595–606.
Persson, B. (2001). “A comparison between mechanical properties of self-compacting concrete and the corresponding properties of normal concrete.” Cement Concr. Res., 31, 193–198.
Said, A., and Nehdi, M. (2007). “Behaviour of reinforced self-consolidating concrete frames.” Proc. Inst. Civil Eng.: Struct. Build., 160(2), 95–104.
Soleymani Ashtiani, M., Dhakal, R. P., and Scott, A. N. (2011). “Bond properties of reinforcement in high-strength self-compacting concrete.” Proc., of the 9th Symp. on High Performance Concrete Design, Verification and Utilization, New Zealand Concrete Society, Auckland, New Zealand.
Soleymani Ashtiani, M., Dhakal, R. P., and Scott, A. N. (2013a). “Post-yield bond behaviour of deformed bars in high-strength self-compacting concrete.” Constr. Build. Mater., 44, 236–248.
Soleymani Ashtiani, M., Scott, A. N., and Dhakal, R. P. (2010). “Mechanical properties of high-strength self-compacting concrete.” Proc., of the 21st Australasian Conf. on the Mechanics of Structures and Materials, Victoria Univ., Melbourne, Australia.
Soleymani Ashtiani, M., Scott, A. N., and Dhakal, R. P. (2013b). “Mechanical and fresh properties of high-strength self-compacting concrete containing class C fly ash.” Constr. Build. Mater., 47, 1217–1224.
Sonebi, M., Tamimi, A. K., and Bartos, P. J. M. (2003). “Performance and cracking behavior of reinforced beams cast with self-consolidating concrete.” ACI Mater. J., 100(6), 492–500.
Standards New Zealand. (2006). “Concrete structures standard. Parts 1 & 2: The desing of concrete structures and commentary.”, Wellington, New Zealand.
Valcuende, M., and Parra, C. (2009). “Bond behaviour of reinforcement in self-compacting concretes.” Constr. Build. Mater., 23(1), 162–170.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Jun 10, 2013
Accepted: Oct 21, 2013
Published online: Jan 6, 2014
Published in print: May 1, 2014
Discussion open until: Jun 6, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.