Testing and Design of Aluminum Alloy Cross Sections in Compression
Publication: Journal of Structural Engineering
Volume 140, Issue 9
Abstract
Aluminum alloys are used in a wide range of engineering applications and are gaining increasing usage in the construction sector, offering high strength-to-weight ratios and good durability. In this paper, a series of stub-column tests on aluminum alloy box sections with and without internal cross stiffeners is carried out to investigate cross-section capacity and to explore the possible exploitation of strain hardening in design. All existing stub-column test results from the literature were also collected. A database containing the results from 346 tests on aluminum alloy stub columns of box, channel, and angle sections, with a wide range of cross-section slendernesses, was formed. The test strengths were compared with the design strengths predicted by the current American, Australian/New Zealand, and European specifications. Furthermore, the test strengths were compared with those predicted by the deformation-based continuous strength method (CSM). Following reliability analyses, the design strengths predicted by the three current design specifications were found to be generally conservative, whereas the CSM offered improved design capacities, owing to its allowance for strain hardening.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The research work described in this paper was supported by a grant from University of Hong Kong under the seed funding program for basic research. The authors are also grateful to Mr. Yiran Li for his assistance in the experimental program as part of his final year undergraduate research project at the University of Hong Kong.
References
Afshan, S., and Gardner, L. (2013). “The continuous strength method for structural stainless steel design.” Thin-Walled Struct., 68, 42–49.
Aluminum Association (AA). (2010). Aluminum design manual, Washington, DC.
American Iron, and Steel Institute (AISI). (2004). “Appendix 1: Design of cold-formed steel structural members using direct strength method.” Supplement 2004 to the North American specification for the design of cold-formed steel structural members, 2001 Ed., Washington, DC.
Ashraf, M., and Young, B. (2011). “Design formulations for non-welded and welded aluminum stub columns using continuous strength method.” Eng. Struct., 33(12), 3197–3207.
ASTM. (1997). “Standard test methods for tension testing of metallic materials.” E8M-97, West Conshohocken, PA.
ASTM. (2010). “Standard test method for indentation hardness of aluminum alloys by means of a Webster hardness gage.” B647-10, West Conshohocken, PA.
Australian/New Zealand Standard (AS/NZS). (1997). “Aluminum structures part 1: Limit state design.” AS/NZS 1664.1:1997, Standards Australia, Sydney, Australia.
Bijlaard, P. P., and Fisher, G. P. (1953). “Column strength of H-sections and square tubes in post buckling range of component plates.”, National Advisory Committee for Aeronautics, Washington, DC.
European Committee for Standardization (CEN). (2006). “Eurocode 3: Design of steel structures—Part 1-4: General rules—Supplementary rules for stainless steels.” EN 1993-1-4:2006, Brussels.
European Committee for Standardization (CEN). (2007). “Eurocode 9: Design of aluminum structures—Part 1-1: General rules—General rules and rules for buildings.” BS EN 1999-1-1:2007, Brussels.
Gardner, L. (2008). “The continuous strength method.” Proc. Inst. Civ. Eng.: Struct. Build., 161(3), 127–133.
Gardner, L., and Ashraf, M. (2006). “Structural design for non-linear metallic materials.” Eng. Struct., 28(6), 926–934.
Gardner, L., and Theofanous, M. (2008). “Discrete and continuous treatment of local buckling in stainless steel elements.” J. Constr. Steel Res., 64(11), 1207–1216.
Gardner, L., Wang, F., and Liew, A. (2011). “Influence of strain hardening on the behavior and design of steel structures.” Int. J. Struct. Stab. Dyn., 11(5), 855–875.
Hassinen, P. (2000). “Compression strength of aluminum columns—Experimental and numerical studies.” Proc., 3rd Int. Conf. Coupled Instabilities of Metal Structures (CIMS’2000), ICP, London, 241–248.
Landolfo, R., Piluso, V., Langseth, M., and Hopperstad, O. S. (1999). “EC9 provisions for flat internal elements: Comparison with experimental results.” Light-Weight Steel and Aluminium Structures, P. Mäkeläinen and P. Hassinen, eds., Elsevier, The Netherlands, 515–522.
Langseth, M., and Hopperstad, O. S. (1997). “Local buckling of square thin-walled aluminum extrusions.” Thin-Walled Struct., 27(1), 117–126.
Li, Z., and Schafer, B. W. (2010). “Buckling analysis of cold-formed steel members with general boundary conditions using CUFSM: Conventional and constrained finite strip methods.” Proc., 20th Int. Specialty Conf. on Cold-Formed Steel Structures, Missouri S&T, 17–31.
Mazzolani, F. M. (1995). Aluminum alloy structures, 2nd Ed., E & FN Spon, London.
Mazzolani, F. M., Faella, C., Piluso, V., and Rizzano, G. (1996). “Experimental analysis of aluminum alloy SHS-members subjected to local buckling under uniform compression.” Proc., 5th Int. Colloquium on Structural Stability, COPPE/Federal Univ. of Rio de Janeiro, Brazil, 475–488.
Mazzolani, F. M., Piluso, V., and Rizzano, G. (1997). “Numerical simulation of aluminum stocky hollow members under uniform compression.” Proc., 5th Int. Colloquium on Stability and Ductility of Steel Structures (SDSS’97), Japan Society of Steel Construction, Nagoya Univ., Japan.
Mazzolani, F. M., Piluso, V., and Rizzano, G. (2001). “Experimental analysis of aluminum alloy channels subjected to local buckling under uniform compression.” Proc., C.T.A., Italian Conf. on Steel Construction, ACS, Milano, Italy, 1–10.
Mazzolani, F. M., Piluso, V., and Rizzano, G. (2011). “Local buckling of aluminum alloy angles under uniform compression.” J. Struct. Eng., 173–184.
Mennink, J. (2002). “Cross-sectional stability of aluminum extrusions: Prediction of the actual local buckling behavior.” Ph.D. thesis, Dept. of Structural Design, Eindhoven Univ. of Technology, Eindhoven, Netherlands.
Moen, L. A., Hopperstad, O. S., and Langseth, M. (1999). “Rotational capacity of aluminium beams under moment gradient. I: Experiments.” J. Struct. Eng., 910–920.
Schafer, B. W., and Peköz, T. (1998). “Direct strength prediction of cold-formed steel members using numerical elastic buckling solutions.” Proc., 14th Int. Specialty Conf. on Cold-Formed Steel Structures, Univ. of Missouri-Rolla, Rolla, MO, 69–76.
Seif, M., and Schafer, B. W. (2010). “Local buckling of structural steel shapes.” J. Constr. Steel Res., 66(10), 1232–1247.
Standards Association of Australia. (2002). “Structural design actions—General principles.” AS 1170-0:2002, Sydney, Australia.
Standards Association of Australia. (2007). “Methods for tensile testing of metals.” AS 1391-2007, Standards Association of Australia, Sydney, Australia.
Su, M., Young, B., and Gardner, L. (2012). “Compression tests of aluminium alloy cross-sections.” Proc., 13th Int. Symp. Tubular Structures, CRC Press/Balkema, The Netherlands, 501–508.
Zhu, J. H., and Young, B. (2006a). “Tests and design of aluminum alloy compression members.” J. Struct. Eng., 1096–1107.
Zhu, J. H., and Young, B. (2006b). “Aluminum alloy tubular columns—Part II: Parametric study and design using direct strength method.” Thin-Walled Struct., 44(9), 969–985.
Zhu, J. H., and Young, B. (2008). “Behavior and design of aluminum alloy structural members.” Adv. Steel Constr., 4(2), 158–172.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 140 • Issue 9 • September 2014
Copyright
© 2014 American Society of Civil Engineers.
History
Received: May 13, 2013
Accepted: Oct 17, 2013
Published online: Apr 8, 2014
Published in print: Sep 1, 2014
Discussion open until: Sep 8, 2014
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.