Developments on the Design of Cold-Formed Steel Angles
Publication: Journal of Structural Engineering
Volume 139, Issue 5
Abstract
This paper presents procedures for the design of fixed- and pin-ended equal-leg angle columns with short-to-intermediate lengths. First, some remarks concerning the buckling and postbuckling behavior of the angle columns are presented that (1) illustrate the main differences between the fixed- and pin-ended column responses and (2) demonstrate the need for specific design procedures. Then, the paper reports an in-depth investigation aimed at gathering a large column ultimate strength data bank that includes (1) experimental values collected from the literature and (2) numerical values obtained from shell finite-element analyses carried out in the code ABAQUS. The set of experimental results is comprised of 41 fixed-ended columns and 37 pin-ended columns and the numerical results obtained include 89 fixed-ended columns and 28 pin-ended columns; various cross-section dimensions, lengths, and yield stresses are considered. Finally, the paper closes with the proposal of new design procedures for fixed- and pin-ended angle columns based on the direct strength method (DSM). The two procedures adopt modified global and local strength curves, and it is shown that the proposed DSM approach leads to accurate ultimate strength estimates for short-to-intermediate columns covering a wide slenderness range.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge Mr. Enio Mesacasa Jr., for the work carried out during his stay in Lisbon and also for sharing some of his recent research results; and the financial support of the Portuguese Foundation for Science and Technology (FCT), through the research project Generalised Beam Theory (GBT) - Development, Application and Dissemination (PTDC/ECM/108146/2008).
References
American Iron and Steel Institute (AISI). (1991). LRFD cold-formed steel design manual, AISI, Washington, DC.
American Iron and Steel Institute (AISI). (1996). AISI specification for the design of cold-formed steel structural members, AISI, Washington, DC.
American Iron and Steel Institute (AISI). (2001). North American specification for the design of cold-formed steel structures (NAS), AISI, Washington, DC.
American Iron and Steel Institute (AISI). (2007). North American specification for the design of cold-formed steel structural members (NAS), AISI, Washington, DC.
Bebiano, R., Silvestre, N., and Camotim, D. (2008). “GBTUL— A code for the buckling analysis of cold-formed steel members.” Proc., 19th Int. Specialty Conf. on Recent Research and Developments in Cold-Formed Steel Design and Construction, R. LaBoube and W.-W. Yu, eds., Univ. of Missouri-Rolla, Rolla, MO, 61–79.
Camotim, D., Basaglia, C., Bebiano, R., Gonçalves, R., and Silvestre, N. (2010). “Latest developments in the GBT analysis of thin-walled steel structures.” Proc., Int. Colloquium on Stability and Ductility of Steel Structures (SDSS), E. Batista, P. Vellasco, and L. Lima, eds., Federal Univ. of Rio de Janeiro and State Univ. of Rio de Janeiro, Rio de Janeiro, Brazil, 33–58.
Chodraui, G. M. B., Shifferaw, Y., Malite, M., and Schafer, B. W. (2006). “Cold-formed steel angles under axial compression.” Proc., 18th Int. Specialty Conf. on Cold-Formed Steel Structures, R. LaBoube and W.-W. Yu, eds., Univ. of Missouri-Rolla, Rolla, MO, 285–300.
Dassault Systèmes Simulia Corp. (DS Simulia). (2008), ABAQUS version 6.7-5 user’s manual, Dassault Systèmes, Providence, RI.
Dinis, P. B., and Camotim, D. (2011). “Buckling, post-buckling and strength of equal-leg angle and cruciform columns: Similarities and differences.” Proc., 6th European Conf. on Steel and Composite Structures (EUROSTEEL), Vol. A, L. Dunai, M. Iványi, K. Jármai, N. Kovács, and L. G. Vigh, eds., European Convention for Constructional Steelwork (ECCS), Brussels, Belgium, 105–110.
Dinis, P. B., Camotim, D., and Silvestre, N. (2010a). “On the local and global buckling behaviour of angle, T-section and cruciform thin-walled columns and beams.” Thin-Walled Struct., 48(10–11), 786–797.
Dinis, P. B., Camotim, D., and Silvestre, N. (2010b). “Post-buckling behaviour and strength of angle columns.” Proc., Int. Colloquium on Stability and Ductility of Steel Structures (SDSS), E. Batista, P. Vellasco, and L. Lima, eds., Federal Univ. of Rio de Janeiro and State Univ. of Rio de Janeiro, Rio de Janeiro, Brazil, 1141–1150.
Dinis, P. B., Camotim, D., and Silvestre, N. (2011). “On the design of steel angle columns.” Proc., 6th Int. Conf. on Thin-Walled Structures (ICTWS), D. Dubina and V. Ungureanu, eds., European Convention for Constructional Steelwork (ECCS), Brussels, Belgium, 271–279.
Dinis, P. B., Camotim, D., and Silvestre, N. (2012a). “On the mechanics of thin-walled angle column instability.” J. Thin-Walled Struct., 52, 80–89.
Dinis, P. B., Camotim, D., and Silvestre, N. (2012b). “Buckling, post-buckling, strength and design of angle columns.” Proc., USB Key Drive Structural Stability Research Council Annual Stability Conf., Structural Stability Research Council, Rolla, MO.
Ellobody, E., and Young, B. (2005). “Behavior of cold-formed steel plain angle columns.” J. Struct. Eng., 131(3), 457–466.
Ganesan, K., and Moen, C. D. (2010). “LRFD and LSD resistance factors for cold-formed steel compression members.” AISI Final Rep. CE/VPI-ST-10/04, Virginia Polytechnic Institute and State Univ., Blacksburg, VA.
Ganesan, K., and Moen, C. D. (2012). “LRFD resistance factor for cold-formed steel compression members.” J. Constr. Steel Res., 72(May), 261–266.
Gaylord, E. H., and Wilhoite, G. M. (1985). “Transmission towers: Design of cold-formed angles.” J. Struct. Eng., 111(8), 1810–1825.
GBTUL 1.0β [Computer software]. Lisbon, Portugal, IST, Technical University of Lisbon.
Kitipornchai, S., and Chan, S. L. (1987). “Nonlinear finite-element analysis of angle and tee beam-columns.” J. Struct. Eng., 113(4), 721–739.
Maia, W. F. (2008). “On the stability of cold-formed steel angle columns.” M.S. thesis, School of Engineering at São Carlos, Univ. of São Paulo, São Paulo, Brazil (in Portuguese).
Maia, W. F., Neto, J. M., and Malite, M. (2008). “Stability of cold-formed steel simple and lipped angles under compression.” Proc., 19th Int. Specialty Conf. on Cold-Formed Steel Structures, R. LaBoube, W.-W. Yu, eds., Univ. of Missouri-Rolla, Rolla, MO, 111–125.
Mesacasa, E. C., Jr. (2011). “Structural behavior and design of cold-formed steel angle columns.” Research Rep., School of Engineering at São Carlos, University of São Paulo, São Paulo, Brazil (in Portuguese).
Popovic, D., Hancock, G. J., and Rasmussen, K. J. R. (1999). “Axial compression tests of cold-formed angles.” J. Struct. Eng., 125(5), 515–523.
Popovic, D., Hancock, G. J., and Rasmussen, K. J. R. (2001). “Compression tests on cold-formed angles loaded parallel with a leg.” J. Struct. Eng., 127(6), 600–607.
Rasmussen, K. J. R. (2005). “Design of angle columns with locally unstable legs.” J. Struct. Eng., 131(10), 1553–1560.
Rasmussen, K. J. R. (2006). “Design of slender angle section beam-columns by the direct strength method.” J. Struct. Eng., 132(2), 204–211.
Schafer, B. W. (2008). “Review: The direct strength method of cold-formed steel member design.” J. Constr. Steel Res., 64(7–8), 766–778.
Shi, G., Liu, Z., and Chung, K. F. (2009). “Numerical study on the local buckling of 420 MPa steel equal angle columns under axial compression.” Proc., 6th Int. Conf. on Advances in Steel Structures (ICASS), Vol. I, S. L. Chan, ed., The Hong Kong Institute of Steel Construction, Hong Kong, 387–394.
Shifferaw, Y., and Schafer, B. W. (2011). “Behavior and design of cold-formed steel lipped and plain angles.” Proc., USB Structural Stability Research Council Annual Stability Conf. (SSRC) Univ. of Missouri-Rolla, Rolla, MO.
Silvestre, N., and Camotim, D. (2010). “On the mechanics of distortion in thin-walled open sections.” Thin-Walled Struct., 48(7), 469–481.
Standards Australia/Standards New Zealand (SA/NZS). (2005). “Cold-formed steel structures.” AS/NZS 4600:2005, Sydney, Australia.
Stowell, E. Z. (1951). “Compressive strength of flanges.” NACA Rep. No. 1029, National Advisory Committee for Aeronautics, National Aeronautics and Space Administration, Washington, DC.
Wilhoite, G., Zandonini, R., and Zavelani, A. (1984). “Behaviour and strength of angles in compression: An experimental investigation.” Proc., ASCE Annual Convention and Structures Congress, ASCE, Reston, VA.
Young, B. (2004). “Tests and design of fixed-ended cold-formed steel plain angle columns.” J. Struct. Eng., 130(12), 1931–1940.
Young, B., and Rasmussen, K. J. R. (1999). “Shift of effective centroid in channel columns.” J. Struct. Eng., 125(5), 524–531.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Sep 2, 2011
Accepted: Jun 5, 2012
Published online: Aug 10, 2012
Published in print: May 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.