Economical Steel Plate Shear Walls for Low-Seismic Regions
Publication: Journal of Structural Engineering
Volume 139, Issue 3
Abstract
Previous research on steel plate shear walls (SPSWs) and current design codes have focused principally on achieving highly ductile behavior through stringent detailing requirements. As such, the system is generally considered to be economical only in high-seismic regions. However, lower demands in other regions may permit the use of more economical options. This paper describes a proposed concept for SPSWs that meets the intent of capacity design, while greatly improving competitiveness in seismic regions where maximum ductility is not required. A large-scale, 2-story SPSW specimen was tested to evaluate the associated performance. The wall had standard double-angle beam-to-column shear connections and was tested under vertical gravity load concurrent with reversing lateral loads at each floor level. The specimen survived 25 lateral load cycles, 18 of which were in the inelastic range. The test results indicated that excellent performance can be expected in low-seismic regions, despite significantly reduced costs, compared with traditional designs. The shear wall showed stable performance at large lateral deformation ratios with high levels of ductility and energy dissipation capacity.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The test specimen was fabricated and donated by Supreme Steel Edmonton. Funding for this research program was provided by the Natural Sciences and Engineering Research Council, Steel Structures Education Foundation, Alberta Heritage Foundation, Canadian Society for Civil Engineering, and the University of Alberta. All support is gratefully acknowledged.
References
AISC. (2010a). “Seismic provisions for structural steel buildings.” ANSI/AISC 341-10, AISC, Chicago.
AISC. (2010b). “Specification for structural steel buildings.” ANSI/AISC 360-10, AISC, Chicago.
Applied Technology Council (ATC). (1992). “Guidelines for cyclic seismic testing of components of steel structures.” Rep. No. 24, Applied Technology Council, Redwood City, CA.
ASCE. (2007). “Seismic rehabilitation of existing buildings.” ASCE/SEI 41-06, ASCE, New York.
ASCE. (2010). “Minimum design loads for buildings and other structures.” ASCE/SEI 7-10, ASCE, Reston, VA.
Berman, J. W., and Bruneau, M. (2005). “Experimental investigation of light-gauge steel plate shear walls.” J. Struct. Eng., 131(2), 259–267.
Berman, J. W., and Bruneau, M. (2008). “Capacity design of vertical boundary elements in steel plate shear walls.” Eng. J. 45(1), 57–71.
Caccese, V., Elgaaly, M., and Chen, R. (1993). “Experimental study of thin steel-plate shear walls under cyclic load.” J. Struct. Eng., 119(2), 573–587.
Canadian Standards Association (CSA). (2004). “General requirements for rolled or welded structural quality steel/structural quality steel.” CSA G40.20-04/G40.21-04 (R2009), Canadian Standards Association, Mississauga, ON, Canada.
Canadian Standards Association (CSA). (2009). “Design of steel structures.” CAN/CSA S16-09, Canadian Standards Association, Mississauga, ON, Canada.
Chen, S.-J., and Jhang, C. (2011). “Experimental study of low-yield-point steel plate shear wall under in-plane load.” J. Construct. Steel Res., 67(6), 977–985.
Dastfan, M., and Driver, R. G. (2012). “Ductile steel plate shear walls with PEC columns.” Structural Engineering Rep. 298, Dept. of Civil and Environmental Engineering, Univ. of Alberta, Edmonton, AB, Canada.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behaviour of steel plate shear walls.” Structural Engineering Rep. 215, Dept. of Civil and Environmental Engineering, Univ. of Alberta, Edmonton, AB., Canada.
Driver, R. G., and Moghimi, H. (2011). “Modular construction of steel plate shear walls for low and moderate seismic regions.” Proc., Structures Congress, Structural Engineering Institute, ASCE, Reston, VA, 758–769.
FEMA. (1997). “NEHRP commentary on the guidelines for the seismic rehabilitation of buildings.” FEMA 274, Washington, D.C.
Moghimi, H., and Driver, R. G. (2011). “Effect of regular perforation patterns on steel plate shear wall column demands.” Proc., Structures Congress, Structural Engineering Institute, ASCE, Reston, VA, 2917–2928.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.” Structural Engineering Rep., No. 114, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, AB, Canada.
Tromposch, E. W., and Kulak, G. L. (1987). “Cyclic and static behaviour of thin panel steel plate shear walls.” Structural Engineering Rep., No. 145, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, AB, Canada.
Information & Authors
Information
Published In
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Jan 3, 2012
Accepted: May 25, 2012
Published online: Feb 15, 2013
Published in print: Mar 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.