Structural Behavior of CHS T-Joints Subjected to Brace Axial Compression in Fire Conditions
Publication: Journal of Structural Engineering
Volume 139, Issue 1
Abstract
The structural behavior of circular hollow section (CHS) T-joints subjected to axial brace compression in fire conditions was investigated. Five full-scale tubular joints with different brace-to-chord diameter ratios were tested under elevated temperature. The tests were in isothermal heating conditions, where the specimens were heated to the desired temperatures and then subjected to static load to failure. The ultimate strength and failure modes of these joints were investigated. It was observed that both the reduction in material strength and changes in localized plastification area beneath the brace decreased the ultimate strength of the joints as temperature increased. Furthermore, local buckling and ovalisation of the chords were found to be more concentrated around the joint region at elevated temperature. To the authors’ best knowledge, these tests were among the first reported experimental investigations in the ultimate strength and failure mechanisms of tubular joints at elevated temperature. To investigate the joint behavior at high temperature in greater detail, FEM was used. The finite-element models were first validated by the test results. The development of failure mechanisms of CHS T-joints at elevated temperature was then traced with the numerical models. The models were also used to quantify the effect of elevated temperatures on three parameters that directly affect the ultimate strength of the T-joints. The three parameters are boundary condition, precompression in the chord, and chord thickness.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was funded by an ARC 2/07 project entitled “Failures modes and ultimate strength of tubular joints under elevated temperatures” from the Ministry of Education, Singapore.
References
ABAQUS 6.9-1 [Computer software]. Providence, RI, Hibbit, Karlsson and Sorensen.
Al-Jabri, K. S., Burgess, I. W., Lennon, T., and Plank, R. J. (2005). “Moment-rotation-temperature curves for semi-rigid joints.” J. Construct. Steel Res., 61(3), 281–303.
American Petroleum Institute (API). (1993). Recommended practice for planning, designing and constructing fixed offshore platforms – Working stress design. 20th Ed., American Petroleum Institute, Washington, DC.
American Petroleum Institute. (2000). “Recommended Practice for Planning Designing and Constructing Fixed Offshore Structures.” API-RP2A, 21st Ed., Washington, DC.
Brazier, L. G. (1927). “On the flexure of thin cylindrical shells and other thin sections.” Royal Society–Proc., 116(A773), 104–114.
Cofer, W. F., Jubran, J. S. (1992). “Analysis of welded tubular connections using continuum damage mechanics.” J. Struct. Eng., 118(3), 828–845.
Cofer, W. F., and Will, K. M. (1990). “An analytical method for ultimate strength evaluation of tubular joints.” Proc., 9th Int. Conf. on Offshore Mechanics and Arctic Engineering, Houston, 209–306.
Elchalakani, M., Zhao, X. L., and Grzebieta, R. H. (2002). “Plastic mechanism analysis of circular tubes under pure bending.” Int. J. Mech. Sci., 44(6), 1117–1143.
European Committee for Standardization (CEN). (2005). “Eurocode 3: Design of Steel Structures, Part 1.2: General Rules–Structural Fire Design,” EC3:P1-2, Brussels, Belgium.
Kurobane, Y. (2006). “New ultimate strength formulae for CHS K joints.” Welding World, 50(special issue), 242–249.
Lalani, M., Gholkar, S. F., and Ward, J. K. (1989). “Recent developments in the ultimate strength assessment of tubular joints: A nonlinear numerical treatment.” Proc., 21st Annual Offshore Technology Conf., Houston, 6158.
Lee, M. M. K. (1999). “Strength, stress and fracture analysis of offshore tubular joints using finite elements.” J. Construct. Steel Res., 51(3), 265–286.
Makino, Y., Kurobane, Y. Ochi, K., Van der Vegte, G. J., and Wilmshurst, S. T. (1996). “Introduction to unstiffened CHS tubular joint database.” 7th Int. Symposium on Tubular Structures, Balkema, Rotterdam, Netherlands, 157–164.
Pecknold, D., Marshall, P., and Bucknell, J. (2007). “New API RP2A tubular joint strength design provisions.” J. Energy Resour. Technol., 129(3), 177–189.
Ramberg, W., and Osgood, W. R. (1943). “Description of stress-strain curves by three parameters.” National Advisory Committee for Aeronautics–Technical Notes, National Advisory Committee for Aeronautics.
van der Valk, C. A. C. (1988). “Factors controlling the static strength of tubular T-joints.” Proc., 5th Int. Conf. on Behavior of Offshore Structures (BOSS-88), Pergamon, Oxford, U.K., 1177–1182.
Van der Vegte, G. J. (1995). “The static strength of uniplanar and multiplanar tubular T- and X-joint.” Ph.D. thesis, Delft University Press, Delft, Netherlands.
Van der Vegte, G. J., and Makino, Y. (2006a). “The ultimate strength of axially loaded CHS uniplanar T-joints subjected to axial chord load.” Welding World, 50, 104–111.
Van der Vegte, G. J., and Makino, Y. (2006b). “Ultimate strength formulation for axially loaded CHS uniplanar T-joint.” Int. J. Offshore Polar Eng., 16(4), 305–312.
Wardenier, J., Packer, J. A., Zhao, X.-L., and van der Vegte, G. J. (2010). Hollow sections in structural applications, Comité International pour le Développement et l'Etude de la Construction Tubulaire (CIDECT), Zoetermeer, Netherlands.
Information & Authors
Information
Published In
Journal of Structural Engineering
Volume 139 • Issue 1 • January 2013
Pages: 73 - 84
Copyright
© 2013 American Society of Civil Engineers.
History
Received: Aug 27, 2011
Accepted: Mar 2, 2012
Published online: Mar 6, 2012
Published in print: Jan 1, 2013
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.