Effect of Plastic Constraint on Brittle Fracture in Steel: Evaluation Using a Toughness Scaling Model
Publication: Journal of Structural Engineering
Volume 138, Issue 6
Abstract
Over the past two decades, plastic constraint effects have been an issue of concern in both fracture mechanics and structural integrity research, and several methods have been proposed for considering loss of plastic constraint. This paper shows the ability of a simplified model to predict brittle fracture under low plastic constraint conditions. Fracture toughness tests are performed on single-edge notched bend (SENB) steel specimens with deep and shallow notches, as well as on double-edge notched tension and center-notched tension (CNT) specimens. When compared with SENB specimens with a deep notch, the CNT specimens show high fracture toughness as a result of the loss of plastic constraint at the crack tip. Here, the Weibull stress approach and a toughness scaling model (TSM) are used to consider the effects of the loss of plastic constraint on the fracture toughness of the specimens. The corrected fracture toughness values evaluated by the TSM are found to be close to the toughness values observed in the tests and to the values predicted by the Weibull stress approach. This paper also briefly discusses the effect of ductile crack growth on brittle fracture.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
This research was supported in part by the Japan Iron and Steel Federation and the Japan Society for the Promotion of Science Grants-in-Aid for Scientific Research. We would like to thank Prof. J. A. Packer (University of Toronto) for his comments on this paper.
References
Anderson, T. L. (1994). Fracture mechanics: Fundamentals and applications, 2nd Ed., CRC Press, Boca Raton, FL.
Anderson, T. L., and Dodds, R. H. Jr. (1991). “Specimen size requirements for fracture toughness testing in the ductile-brittle transition region.” J. Test. Eval.JTEVAB, 19(2), 123–134.
Azuma, K., Kurobane, Y., Iwashita, T., and Makino, Y. (2001). “Fracture from fatigue cracks installed at weld toes of plate to plate T-joints.” Int. J. Offshore Polar Eng.IOPEE7, 11(2), 125–132.
Beremin, F. M. (1983). “A local criterion for cleavage fracture of a nuclear pressure vessel steel.” Metall. Trans. AMTTABN, 14(11), 2277–2287.
BSI. (1991). “Fracture mechanics toughness tests—Part 1: Method for determination of KIc, critical CTOD and critical values of metallic materials.” BS 7448-1, London.
Cicero, S., Ainsworth, R. A., and Gutiérrez-Solana, F. (2010). “Engineering approaches for the assessment of low constraint fracture conditions: A critical review.” Eng. Fract. Mech.EFMEAH, 77(8), 1360–1374.
Iwashita, T., Kurobane, Y., Azuma, K., and Makino, Y. (2003). “Prediction of brittle fracture initiating at ends of CJP groove welded joints with defects: study into applicability of failure assessment diagram approach.” Eng. Struct.ENSTDF, 25(14), 1815–1826.
Knott, J. F. (1973). Fundamentals of fracture mechanics, Chapter 3, Butterworths, London.
Kuwamura, H., Iyama, J., and Matsui, K. (2003). “Effects of material toughness and plate thickness on brittle fracture of steel members.” J. Struct. Eng.JSENDH, 129(11), 1475–1483.
Kuwamura, H., and Yamamoto, K. (1997). “Ductile crack as trigger of brittle fracture in steel.” J. Struct. Eng.JSENDH, 123(6), 729–735.
Matos, C. G., and Dodds, R. H. Jr. (2001). “Probabilistic modeling of weld fracture in steel frame connections, part I: Quasi-static loading.” Eng. Struct.ENSTDF, 23(8), 1011–1030.
Minami, F., Bruckner-Foit, A., Munz, D., and Trolldenier, B. (1992). “Estimate procedure for the Weibull parameters used in the local approach.” Int. J. Fract.IJFRAP, 54(3), 197–210.
Minami, F., Ruggieri, C., Ohata, M., and Toyoda, M. (1996). “[Evaluation of specimen geometry effect on brittle fracture resistance based on the local approach].” J. Soc. Mater. Sci. Jpn.ZARYAQ, 45(5), 544–551 (in Japanese).
Minami, F., Ohata, M., Shimanuki, H., Handa, T., Igi, S., Kurihara, M., Kawabata, T., Yamashita, Y., Tagawa, T., and Hagihara, Y. (2006). “Method of constraint loss correction of CTOD fracture toughness for fracture assessment of steel components.” Eng. Fract. Mech.EFMEAH, 73(14), 1996–2020.
Minami, F., et al. (2007). “[Significance of fracture toughness of laser welds for structural steels and fracture performance assessment by Weibull stress criterion-Improvement of steel structural performance by laser beam welding for mid-thick section steel plate].” Yosetsu Gakkaishi (J. Jpn. Weld. Soc.)YOGAAK, 25(1), 149–158 (in Japanese).
Ohata, M., Handa, T., Mimura, H., Tagawa, T., and Minami, F. (2006). “Guideline for determination of Weibull parameter.” 9th Euro. Mech. of Mater. Conf., Moret Sur Loing, France, Paper 52, MINES ParisTech, Paris.
Riesch-Oppermann, H., and Diegele, E. (2002). “Elements of a fracture mechanics concept for the cleavage fracture behaviour of RAFM steels using local fracture criteria.” FZKA Rep. 6668, Forschungszentrum Karlsruhe, Karlsruhe, Germany.
Ruggieri, C., and Dodds, R. H. Jr. (1996). “A transferability model for brittle fracture including constraint and ductile effects: a probabilistic approach.” Int. J. Fract.IJFRAP, 79(4), 309–340.
Ruggieri, C., Panontin, T. L., and Dodds, R. H. Jr. (1990). “Numerical modeling of ductile crack growth in 3-D using computational cell elements.” Int. J. Fract.IJFRAP, 82(1), 67–95.
Tagawa, T., Kayamori, Y., and Hira, H. (2010). “Statistical scatter of fracture toughness in the ductile—brittle transition of a structural steel.” Eng. Fract. Mech.EFMEAH, 77(16), 3077–3086.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Feb 22, 2011
Accepted: Sep 23, 2011
Published online: Sep 26, 2011
Published in print: Jun 1, 2012
Published ahead of production: Jun 15, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.