Numerical Modeling of Shear Behavior of Reinforced Concrete Pile Caps
Publication: Journal of Structural Engineering
Volume 138, Issue 6
Abstract
The application of bending theory based methods and strut-and-tie models for the design of pile caps to resist shear is still a subject of debate, with the latest Eurocodes permitting both methods but not giving much guidance as to their use. The former UK design standards for concrete buildings and bridges, recently withdrawn, gave more guidance, and it is likely that these methods will continue to be used by designers. However, there is considerable discrepancy between these standards, particularly with regard to the width of cap over which shear enhancement at short spans may be applied, and how much longitudinal reinforcement to take as a tie in the strut-and-tie method. Both standards are also seen as conservative. To gain a better understanding of the problem and assess the available design methods, nonlinear finite-element analysis has been performed to investigate the shear behavior of four-pile reinforced concrete pile caps, under full-width wall loading. The models were validated against an experimental program that included an optical photogrammetric method for measuring full-field displacements. An extensive parametric study was carried out, varying shear span, cap width, and reinforcement ratio over a practical range. The conservatism of the UK design standards, and the real shear capacity of the pile caps were found to be a function of shear enhancement factor and the width of the cap over which shear enhancement is applied. Strut-and-tie behavior was observed in the models, and a commonly used strut-and-tie method was found to give fairly good predictions. A modified strut-and-tie method is suggested for this particular configuration of a four-pile cap under full-width loading, which gives more accurate predictions. This is especially so for samples with large transverse pile spacing, where a significant proportion of the longitudinal reinforcement over the width of the cap can be assumed to participate in the yielding ties.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
We are grateful to the UK Engineering and Physical Sciences Research Council (EPSRC) for the project funding under Grant Ref. GR/S17888/01.
References
Adebar, P., and Zhou, Z. (1996). “Design of deep pile caps by strut-and-tie models.” ACI Struct. J.ASTJEG, 93(4), 437–448.
American Association of State and Highway Transportation Officials (AASHTO). (2007). “LRFT bridge design specifications-SI units.” 4th Ed., American Association of State and Highway Transportation Officials, Washington, DC.
American Concrete Institute (ACI). (2005). “Building code requirements for structural concrete.” ACI 318R-05, Farmington Hills, MI.
Bazant, Z. P., and Oh, B. H. (1983). “Crack band theory for fracture of concrete.” Mater. Constr.MCUAAA, 16(3), 155–177.
Bloodworth, A. G., Jackson, P. A., and Lee, M. M. K. (2003). “The strength of reinforced concrete pile caps.” Proc. ICE Struct. Build., 156(4), 347–358.
British Standards Institution (BSI). (1990). “Steel, concrete and composite bridges: Part 4: Code of practice for design of concrete bridges.” BS 5400, Milton Keynes, UK.
British Standards Institution (BSI). (1997). “Structural use of concrete: Part 1: Code of practice for design and construction.” BS 8110, Milton Keynes, UK.
British Standards Institution (BSI). (2004). “Design of concrete structures—Part 1–1: General rules and rules for buildings.” BS EN 1992-1-1, Milton Keynes, UK.
British Standards Institution (BSI). (2005). “Eurocode 2—Design of concrete structures—Part 2: Concrete bridges—Design and detailing rules.” BS EN 1992-2, Milton Keynes, UK.
Canadian Standards Association (CSA). (1994). “Canadian standard for the design of concrete structures.” A23.3-94, Mississauga, ON, Canada.
Cao, J. (2009). “The shear behaviour of the reinforced concrete four-pile caps.” Ph.D. thesis, Univ. of Southampton, Southampton, UK.
Cao, J., and Bloodworth, A. G. (2012). “Shear behaviour of reinforced concrete pile caps under full-width wall loading.” Proc., ICE: Struct. Build., 165(4), 165–177.
Cao, J., Bloodworth, A. G., and Xu, M. (2007). “Observations of truss action in reinforced concrete pile caps.” Proc., 3rd Int. Conf. on Structural Engineering, Mechanics and Computation, Millpress, Rotterdam, Netherlands.
Clarke, J. L. (1973). “Behaviour and Design of Pile Caps with Four Piles.” Technical Rep. 124-136, Cement and Concrete Association, London.
DIANA. (2002). DIANA finite element analysis user's manual release 8.1, TNO DIANA BV, Delft, The Netherlands.
DIANA. (2005). Standard DIANA course tutorials and exercises, TNO DIANA BV, Delft, The Netherlands.
Keown, P. G. (2000). “Investigation of the shear characteristics of reinforced concrete continuous beams.” Ph.D. thesis, Queen’s University, Belfast, UK.
Park, J., Kuchma, D., and Souza, R. (2008). “Strength predictions of pile caps by a strut-and-tie model approach.” Can. J. Civ. Eng.CJCEB8, 35(12), 1399–1413.
Regan, P. E. (1971). Shear in reinforced concrete—an analytical study, Construction Industry Research and Information Association, Imperial College, London.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Nov 22, 2010
Accepted: Aug 25, 2011
Published online: Aug 27, 2011
Published in print: Jun 1, 2012
Published ahead of production: Jun 15, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.