Rotational Stiffness of Exposed Column Base Connections: Experiments and Analytical Models
Publication: Journal of Structural Engineering
Volume 138, Issue 5
Abstract
The rotational flexibility of column base connections is often ignored in structural simulation of moment frames in which the bases are assumed to be either fixed or pinned. Although structural response is sensitive to base flexibility, methods to properly characterize base flexibility are not readily available. Motivated by these issues, a new approach to characterize the rotational flexibility of exposed column base connections is presented in this paper. The method leverages existing design procedures for base connection design, such that the rotational stiffness may be calculated with modest effort once the design has been completed. The method is validated through comparison with nine experiments, which interrogate a range of parameters including base-plate size and thickness, level of axial load, anchor-rod strength, and concrete strength. The comparison between the test and the predicted values indicates that, on average, the method predicts the stiffness with accuracy, such that the average test-to-predicted ratio is 0.89. The method is particularly accurate for conditions in which the moment-to-axial-load ratio is large, whereas it overestimates the stiffness of connections with high axial load, relative to the applied moment. A detailed analysis of the results is presented, accompanied by a discussion of the limitations of the proposed approach.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors are grateful to the American Institute of Steel Construction, which funded the experiments that served as the validation test bed for this study. The authors also thank Ivan Gomez of AIR-Worldwide and Gregory Deierlein of Stanford University for their support and close collaboration in the planning and conduct of the experiments. The staff at the NEES Berkeley site also receives our gratitude. The findings presented in this paper reflect the views of the authors and not those of any funding agency.
References
American Concrete Institute (ACI) 318. (2002). “Building code requirements for structural concrete and commentary.” ACI 318-02, ACI 318R-02, Detroit.
ASCE Task Committee on Design Criteria for Composite Structures in Steel and Concrete. (1998). “Design guide for partially restrained composite connections.” J. Struct. Eng., 124(10), 1099–1114.
Astaneh, A., Bergsma, G., and Shen, J. H. (1992). “Behavior and design of base plates for gravity, wind and seismic loads.” Proc., National Steel Construction Conference, AISC, Chicago.
Aviram, A., Stojadinovic, B., and Kiureghian, A. (2010). “Performance and reliability of exposed column base plate connections for steel moment-resisting frames.” PEER Rep. 2010/107, Pacific Earthquake Engineering Research Center, Berkeley, CA.
Balut, N., and Moldovan, A. (1997). “A model for the behavior of column base connections.” Proc., 2nd International Conf. STESSA, ATLSS Engineering Center, Lehigh Univ., Bethlehem, PA.
Bjorhovde, R., Colson, A., and Brozzetti, J. (1990). “Classification system for beam-to-column connections.” J. Struct. Eng.JSENDH, 116(11), 3059–3076.
Burda, J. J., and Itani, A. M. (1999). “Studies of seismic behavior of steel base plates.” Rep. No. CCEER 99-7, Center for Civil Engineering Earthquake Research, Dept. of Civil Engineering, Univ. of Nevada, Reno, NV.
Delhomme, F., Debicki, G., and Chaib, Z. (2010). “Experimental behaviour of anchor bolts under pullout and relaxation tests.” Constr. Build. Mater.CBUMEZ, 24(3), 266–274.
DeWolf, J. T., and Sarisley, E. F. (1980). “Column base plates with axial loads and moments.” J. Struct. Div.JSDEAG, 106(11), 2167–2184.
Dumas, M., Beaulieu, D., and Picard, A. (2006). “Characterization equations for steel column base connections.” Can. J. Civ. Eng.CJCEB8, 33(4), 409–420.
Ermopoulos, J., and Stamatopoulos, G. (1996a). “Analytical modeling of column base plates under cyclic loading.” J. Constr. Steel Res., 40(3), 225–238.
Ermopoulos, J., and Stamatopoulos, G. (1996b). “Mathematical modeling of column base plate connections.” J. Constr. Steel Res., 36(2), 79–100.
Ermopoulos, J., Stamatopoulos, G., and Owens, G. (1995). “Influence of support conditions on the behavior of steel frames.” Proc., Nordic Steel Construction Conference, Norwegian Steel Association, Oslo, Norway.
Fahmy, M., Stojadinovic, B., and Goel, S. C. (1999). “Analytical and experimental behavior of steel column bases.” Proc., 8th Canadian Conf. on Earthquake Engineering, Canadian Association for Earthquake Engineering, Ottawa.
Fisher, J. M., and Kloiber, L. A. (2006). Design guide 1: Base plate and anchor rod design, 2nd Ed., American Institute of Steel Construction, Chicago.
Gomez, I., Deierlein, G., and Kanvinde, A., (2010). “Exposed column base connections subjected to axial compression and flexure.” Final Rep. Presented to the American Institute of Steel Construction, Chicago.
Grauvilardell, J. E., Lee, D., Hajjar, J. F., and Dexter, R. J. (2005). “Synthesis of design, testing and analysis research on steel column base plate connections in high seismic zones.” Structural Engineering Rep. No. ST-04-02, Dept. of Civil Engineering, Univ. of Minnesota, Minneapolis.
Higgs, H. R., and Waas, G. (1985). “Influence of foundation flexibility on soil-structure interaction.” Earthquake Eng. Struct. Dyn.IJEEBG, 13(5), 597–615.
Jaspart, J. P., and Vandegans, D. (1998). “Application of component method to column bases.” J. Constr. Steel Res.JCSRDL, 48(2–3), 89–106.
Maan, O., and Osman, A. (2002). “The influence of column base flexibility on the seismic response of steel framed structures.” Proc., 4th Structural Specialty Conf. of the Canadian Society for Civil Engineering, CSCE, Montréal.
Melchers, R. E. (1992). “Column-base response under applied moment.” J. Constr. Steel Res.JCSRDL, 23(1–3), 127–143.
Myers, A. T., Kanvinde, A. M., Deierlein, G. G., and Fell, B. V. (2009). “Effect of weld details on the ductility of steel column baseplate connections.” J. Constr. Steel Res.JCSRDL, 65(6), 1366–1373.
Picard, A., and Beaulieu, D. (1985). “Behavior of a simple column base connection.” Can. J. Civ. Eng.CJCEB8, 12(1), 126–136.
Salmon, C. G., Shaker, L., and Johnston, B. G. (1957). “Moment-rotation characteristics of column anchorages.” Trans. Am. Soc. Civ. Eng.TACEAT, 122, 132–154.
Sato, K. (1987). “A research on the aseismic behavior of steel column base for evaluating its strength capacity and fixity.” Rep. No. 69, Kajima Institute of Construction Technology, Tokyo.
Steenhuis, M., Wald, F., Sokol, Z., and Stark, J. (2008). “Concrete in compression and base plate in bending.” HeronHERNDU, 53(1–2), 51–67.
Thambiratnam, D. P., and Paramasivam, P. (1986). “Base plates under axial loads and moments.” J. Struct. Eng.JSENDH, 112(5), 1166–1181.
Timoshenko, S. P. (1947). Strength of materials, 2nd Ed., Van Nostrand, D. Company, Lancaster, PA.
Tremblay, R., Filiatrault, A., Timler, P., and Bruneau, M. (1995). “Performance of steel structures during the 1994 Northridge earthquake.” Can. J. Civ. Eng.CJCEB8, 22(2), 338–360.
Wald, F., Sokol, Z., and Steenhuis, M. (1994). “The tests of the column-base components.” Proc., First International Conf. STESSA, Timisoara, Romania.
Wald, F., Sokol, Z., and Steenhuis, M. (1995). “Proposal of the stiffness design model of the column bases.” Proc., Third International Workshop on Connections in Steel Structures 3, AISC, Chicago.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Apr 8, 2011
Accepted: Aug 15, 2011
Published online: Aug 17, 2011
Published in print: May 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.