Finite-Element Investigation and Design Recommendations for Perforated Steel Plate Shear Walls
Publication: Journal of Structural Engineering
Volume 135, Issue 11
Abstract
This paper presents results from an investigation of the behavior of unstiffened thin steel plate shear wall (SPSW) having a regular pattern of openings (a.k.a. perforated SPSW). Finite element monotonic pushover analyses were conducted, first on a series of individual perforated strips with variation in perforation diameter, to develop a fundamental understanding of the behavior of complete perforated SPSW, then on a corresponding series of complete perforated SPSW having various perforation diameters. Three different sets of wall boundary conditions are considered, namely: flexible beam laterally braced, rigid floor, and rigid beam. Though some differences between the SPSW panel strips and the individual strip results are observed at large monitored strain, at lower monitored strain however the two models are in a good agreement. Based on the analytical results design recommendations of these perforated SPSWs are presented. The shear strength of a SPSW infill plate having a pattern of multiple regularly spaced circular perforations can be calculated as a function of the shear strength of a solid panel, perforation diameter, and distance between perforations.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Analytical work in this study was performed at the Center for Computational Research at the University at Buffalo, the State University of New York. This work was supported by the Earthquake Engineering Research Centers Program of the National Science Foundation under Grant No. UNSPECIFIEDECC-9701471 to the Multidisciplinary Center for Earthquake Engineering Research. However, any opinions, findings, conclusions, and recommendations presented in this paper are those of the writers and do not necessarily reflect the views of the sponsors.
References
Behbahanifard, M. R., Grondin, G. Y., and Elwi, A. E. (2003). “Experimental and numerical investigation of steel plate shear wall.” Rep. No. 254, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta.
Berman, J. W., and Bruneau, M. (2003). “Experimental investigation of light-gauge steel plate shear walls for the seismic retrofit of buildings.” Technical Rep. No. MCEER-03-0001, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, N.Y.
Berman, J. W., and Bruneau, M. (2005). “Experimental investigation of light-gauge steel plate shear walls.” J. Struct. Eng., 131(2), 259–267.
Dexter, R. J., Alttstadt, S. A., and Gardner, C. A. (2002). Strength and ductility of HPS70W tension members and tension flanges with holes, University of Minnesota, Minneapolis.
Driver, R. G., Kulak, G. L., Kennedy, D. J. L., and Elwi, A. E. (1997). “Seismic behavior of steel plate shear walls.” Rep. No. 215, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta.
Elgaaly, M., and Liu, Y. (1997). “Analysis of thin-steel-plate shear walls.” J. Struct. Eng., 123(11), 1487–1496.
Hibbitt, Karlsson, and Sorenson, Inc. (HKS). (2004a). ABAQUS/CAE user’s manual version 6.5-1, Hibbitt, Karlsson, and Sorenson, Inc., Pawtucket, R.I.
Hibbitt, Karlsson, and Sorenson, Inc. (HKS). (2004b). ABAQUS/Standard user’s manual version 6.5-1, Hibbitt, Karlsson, and Sorenson, Inc., Pawtucket, R.I.
Hitaka, T., and Matsui, C. (2003). “Experimental study on steel shear wall with slits.” J. Struct. Eng., 129(5), 586–595.
Kaufmann, E. J., Metrovich, B., and Pense, A. W. (2001). “Characterization of cyclic inelastic strain behavior on properties of A572 Gr. 50 and A913 Gr. 50 rolled sections.” Rep. No. 01-13, National Center for Engineering Research on Advanced Technology for Large Structural Systems, Lehigh Univ., Bethlehem, Pa.
Purba, R., and Bruneau, M. (2007). “Design recommendations for perforated steel plate shear walls.” Technical Rep. No. MCEER-07-0011, Multidisciplinary Center for Earthquake Engineering Research, State Univ. of New York at Buffalo, Buffalo, N.Y.
Roberts, T., and Sabouri-Ghomi, S. (1992). “Hysteretic characteristics of unstiffened perforated steel plate shear panels.” Thin-Walled Struct., 14, 139–151.
Sabelli, R., and Bruneau, M. (2007). Steel plate shear walls (AISC design guide), American Institute of Steel Construction, Inc., Chicago, Ill.
Thorburn, L. J., Kulak, G. L., and Montgomery, C. J. (1983). “Analysis of steel plate shear walls.” Rep. No. 107, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta.
Timler, P. A., and Kulak, G. L. (1983). “Experimental study of steel plate shear walls.” Rep. No. 114, Dept. of Civil Engineering, Univ. of Alberta, Edmonton, Alta.
Vian, D., and Bruneau, M. (2005). “Steel plate shear walls for seismic design and retrofit of building structures.” Technical Rep. No. MCEER-05-0010, Multidisciplinary Center for Earthquake Engineering Research, State Univ. of New York at Buffalo, Buffalo, N.Y.
Information & Authors
Information
Published In
Copyright
© 2009 ASCE.
History
Received: Mar 12, 2008
Accepted: Apr 14, 2009
Published online: Apr 16, 2009
Published in print: Nov 2009
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.