Effect of Adhesive through Pilot Pull-Out Tests on Handcrafted Headed Studs Postinstalled in Steel Fiber Concrete
This article has been corrected.
VIEW CORRECTIONPublication: Practice Periodical on Structural Design and Construction
Volume 26, Issue 4
Abstract
This study proposes a practical solution for installing anchoring elements on hard or old concrete surfaces to receive tensile forces. For this situation, where the anchorages will be postinstalled, there is often no depth in the concrete base that meets the minimum straight length of standard anchoring. Thus, the use of headed studs or hooked anchor bolts are the most recommended solutions, but the procedure for installing these elements is still the subject of experimental investigations. Then, the technique of postinstallation of headed studs in hardened concrete niches and the use of structural epoxy resin in the new-old concrete interface is presented. Additionally, the influence of the addition of steel fiber on the anchorage studs performance was also evaluated.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
The authors thank the Institute of Ecological Research in the Amazon (IPEAM) for their support in the development of this study and other research in the Amazon.
References
ABNT (Brazilian Association of Technical Standards). 1978. Design of concrete structures—Procedure. [In Portuguese.]. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 1985. Design and execution of precast concrete structures. [In Portuguese.]. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2007. Concrete steel fibers—Specification. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2014. Design of concrete structures—Procedure. Rio de Janeiro, Brazil: ABNT.
ABNT (Brazilian Association of Technical Standards). 2015. Hot-rolled, high strength low alloy steel, plates and heavy thickness coils, with improved atmospheric corrosion resistance, for structural use—Requirements. [In Portuguese.]. Rio de Janeiro, Brazil: ABNT.
ACI (American Concrete Institute). 2014. Building code requirements for structural concrete and commentary. Farmington Hill, MI: ACI.
Al-Sabah, S., S. N. A. Sourav, and C. Mc Nally. 2021. “The post-installed screw pull-out test: Development of a method for assessing in-situ concrete compressive strength.” J. Build. Eng. 33 (1): 101568. https://doi.org/10.1016/j.jobe.2020.101658.
ASTM. 2005. Standard specification for deformed and plain billet-steel bars for concrete reinforcement. West Conshohocken, PA: ASTM.
ASTM. 2020a. Standard specification for blended hydraulic cements. West Conshohocken, PA: ASTM.
ASTM. 2020b. Standard test method for compressive strength of cylindrical concrete specimens. West Conshohocken, PA: ASTM.
Ballarini, R., and X. Yueyue. 2017. “Fracture mechanics model of anchor group breakout.” J. Eng. Mech. 143 (4): 04016125. https://doi.org/10.1061/(ASCE)EM.1943-7889.0001200.
Bode, H., and K. Roik. 1987. Head studs—Embedded in concrete and loaded in tension: Anchorage to concrete. Detroit, MI: American Concrete Institute.
Comité Euro-International, du Béton. 1996. CEB bulletin d’information 233: Design of fastenings in concrete—Design guide—Parts 1–3. London: Thomas Telford.
Eligehausen, R., W. Fuchs, and B. Mayer. 1988. Tragverhalten von Dübelbefestingungen bei Zugbeanspruchung, Teil 2. Betonwerk + Fertigteil—Techinik 1, 29–35. [In German.] Germany: Betonwerk und Fertigteil-Technik.
Eligehausen, R., R. Mallée, and J. Silva. 2006. Anchorage in concrete construction, 378. Berlin: Wilhelm Ernst & Sohn.
fib (Fédération Internationale du Béton). 2011. Design of anchorages in concrete. Lausanne, Switzerland: fib.
Fuchs, W., R. Eligehausen, and J. E. Breen. 1995. “Concrete capacity design (CCD) approach for fastening to concrete.” ACI Struct. J. 92 (1): 73–94.
Giresini, L., M. L. Puppio, and F. Taddei. 2020. “Experimental pull-out tests and design indications for strength anchors installed in masonry walls.” Mater. Struct. 53 (2): 103. https://doi.org/10.1617/s11527-020-01536-2.
Jonak, J., R. Karpiński, M. Siegmund, A. Machrowska, and D. Prostański. 2021. “Experimental verification of standard recommendations for estimating the load-carrying capacity of undercut anchors in rock material.” Adv. Sci. Technol. Res. J. 15 (1): 230–244. https://doi.org/10.12913/22998624/132279.
Jonak, J., R. Karpiński, M. Siegmund, A. Wójcik, and K. Jonak. 2020. “Analysis of the rock failure cone size relative to the group effect from a triangular anchorage system.” Materials (Basel) 13 (Jan): 4657. https://doi.org/10.3390/ma13204657.
Kalthoff, M., and M. Raupach. 2021. “Pull-out behaviour of threaded anchors in fibre reinforced ordinary concrete and UHPC for machine tool constructions.” J. Build. Eng. 33 (1): 101842. https://doi.org/10.1016/j.jobe.2020.101842.
Klingner, R. E., and J. A. Mendonca. 1982. “Tensile capacity of short anchor bolts and welded shads.” J. Proc. 79 (4): 270–279.
Mahrenholtz, P., and R. L. Wood. 2020. “Design of post-installed and cast-in-place anchors according to the new EN 1992-4 and ACI 318-19.” Struct. Concr. 2020 (1): 1–16. https://doi.org/10.1002/suco.202000118.
Martins, J. D. 2006. “Tensile strength of anchor bolts with end plates embedded in concrete.” Dissertação de Mestrado em Estruturas e Construção Civil. Departamento de Engenharia Civil e Ambiental, Universidade de Brasília.
Nilforoush, R., M. Nilsson, and L. Elfgren. 2017. “Experimental evaluation of tensile behaviour of single cast-in-place anchor bolts in plain and steel fibre-reinforced normal- and high-strength concrete.” Eng. Struct. 147 (89): 195–206. https://doi.org/10.1016/j.engstruct.2017.05.062.
Nzambi A. K. L. L., D. R. C. Oliveira, A. M. Oliveira, and M. S. Picanço. 2021. “Pull-out tests of ribbed steel reinforcing bars embedded in concrete with steel fibres.” Proc. Inst. Civ. Eng. 174 (3): 181–189. https://doi.org/10.1680/jstbu.17.00180.
Oliveira, D. R. C., A. M. Oliveira, and V. G. Costa. 2018. “Pull-out tests on handcrafted headed studs.” Proc. Inst. Civ. Eng. 172 (9): 625–631. https://doi.org/10.1680/jstbu.17.00177.
PCI Design Handbook. 2004. Precast and prestressed concrete, 6th ed. Chicago: Precast/Prestressed Concrete Institute.
Shaik, A., and Y. Whayong. 1985. “In-place strength of welded headed studs.” J. Prestress. Concr. Inst. 30 (2): 56–81.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Oct 16, 2020
Accepted: May 21, 2021
Published online: Aug 9, 2021
Published in print: Nov 1, 2021
Discussion open until: Jan 9, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Aaron Kadima Lukanu Lwa Nzambi, Dênio Ramam Carvalho de Oliveira, Heber Dioney Sousa Moraes, Effect of Headed Stud Thickness Embedded in Steel Fiber Concrete on Pull-Out Strength, Practice Periodical on Structural Design and Construction, 10.1061/PPSCFX.SCENG-1435, 29, 2, (2024).
- Aaron Kadima Lukanu Lwa Nzambi, Dênio Ramam Carvalho de Oliveira, Hermes Matos do Nascimento, Eloisa Pires Azevedo, Effect of the Failure Surface Inclination of Punching with Studs as Shear Reinforcement, Practice Periodical on Structural Design and Construction, 10.1061/PPSCFX.SCENG-1199, 28, 2, (2023).
- Łukasz Kampa, Agnieszka Chowaniec, Aleksandra Królicka, Łukasz Sadowski, Adhesive properties of an epoxy resin bonding agent modified with waste granite powder, Journal of Coatings Technology and Research, 10.1007/s11998-022-00620-2, 19, 5, (1303-1316), (2022).