Sizing Welds Taking into Account the Direction of Loading
Publication: Practice Periodical on Structural Design and Construction
Volume 26, Issue 3
Abstract
The traditional approach of assuming that the throat of the fillet weld resists the load, regardless of the direction of loading is followed in Indian steel code IS 800. However, based on experimental research, the American Structural Welding Code-Steel, the American Institute of Steel Construction code, and the Canadian code have modified the equations to consider the direction of loading. These provisions are discussed, and three examples are also included to show that economic design of weld material can be achieved by using these provisions. Although the end fillet may resist more loads, it may have less ductility than the side fillet. Hence, the designer should exercise caution while using the end fillet, especially when ductility is required in situations where overloading is likely to occur.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data generated during this study appear in the published article. All the equations are available in the respective National Codes.
Acknowledgments
I wish to acknowledge the help of Dr. Adil Dar, Postdoctoral Research Fellow, Department of Civil and Environmental Engineering, National University of Singapore, and Dr. Ahmad Fayeq, Postdoctoral Research Fellow, Indian Institute of Technology, New Delhi in preparing the drawings of this paper.
References
ANSI/AISC. 2016. Specification for structural steel buildings. ANSI/AISC 360. Chicago: AISC.
ANSI/AWS. 2010. Structural welding code: Steel. ANSI/AWS D1.1-2010. New York: ANSI/AWS.
BIS (Bureau of Indian Standards). 2007. General constructions in steel-code of practice. IS 800. New Delhi, India: BIS.
Butler, L., and G. Kulak. 1971. “Strength of fillet welds as a function of direction of load.” Welding J. 50 (5): 231–234.
CSA (Canadian Standards Association). 2009. Design of steel structures. CSA S16:2009. Mississauga, ON: CSA.
Funderburk, R. S. 1999. “Selecting filler metals: Matching strength criteria.” Welding Innovation 16 (2): 10–12.
Gomez, I., A. Kanvinde, Y. K. Kwan, and G. Grondin. 2008. Strength and ductility of welded joints subjected to out-of-plane bending. Chicago: AISC.
Higgins, T. R., and F. R. Preece. 1968. “Proposed working stresses for fillet welds in building construction.” Welding J. 47 (10): 429–432.
Lesik, D. F., and D. J. L. Kennedy. 1990. “Ultimate strength of fillet welded connections loaded in plane.” Can. J. Civ. Eng. 17 (1): 55–67. https://doi.org/10.1139/l90-008.
Miazga, G., and D. J. L. Kennedy. 1989. “Behavior of fillet welds as a function of angle of loading.” Can. J. Civ. Eng. 16 (4): 583–599. https://doi.org/10.1139/l89-089.
Miller, D. K. 1998. “Consider direction of loading when sizing fillet welds-practical ideas for the design professional.” Welding Innovation 15 (2): 2.
Ng, A. K. F., R. G. Driver, and G. Y. Grondin. 2002. Behaviour of transverse fillet welds. Edmonton, AB: Dept. of Civil and Environmental Engineering, Univ. of Alberta.
Subramanian, N. 2016. Design of steel structures-limit states method, 883. New Delhi, India: Oxford University Press.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 31, 2020
Accepted: Feb 26, 2021
Published online: Apr 19, 2021
Published in print: Aug 1, 2021
Discussion open until: Sep 19, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.