Strengthening Load-Bearing Wall Openings Using Concrete Beams and CFRP: Case Study
Publication: Practice Periodical on Structural Design and Construction
Volume 25, Issue 2
Abstract
In building rehabilitation and strengthening works, the need to create openings in existing walls is usual. When those walls are load-bearing walls, the loading path is locally altered; therefore, it is required to strengthen the vicinity of the new opening. In this paper, two strengthening techniques widely applied to strengthen openings in existing walls are described. Those techniques are structurally different; the first technique makes use of reinforced concrete beams, and the second uses externally bonded carbon fiber–reinforced polymer (CFRP) strips. The concrete-beam technique can also be used to underpin structural elements when existing load-bearing walls are completely eliminated. Onsite observations have allowed the conclusion that good strengthening results can be obtained. Additionally, those construction practices are carried out with minimum disruption inside the building. The main parameters defining the strengthening technique choice are the length of the opening, the material, and the width of the existing wall. The loading values acting in existing walls, in principle, have no influence on the strengthening technique choice. The knowledge described in this paper is a first step to promote numerical and laboratory research related to opening strengthening and at the same time to support the development of innovating strengthening techniques.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
No data, models, or code were generated or used during the study.
Acknowledgments
The author would like to acknowledge Julien Dequeker, site engineer, and Paulo Oliveira, site manager, both from Vinci Construction, France, for their technical support.
References
ACI (American Concrete Institute). 2008. Guide for the design and construction of externally bonded FRP systems for strengthening concrete structures. ACI 440.2R. Farmington Hills, MI: ACI.
ACI (American Concrete Institute). 2011. Building code requirements for structural concrete and commentary. ACI 318. Farmington Hills, MI: ACI.
Albert, M. L., A. E. Elwi, and R. J. J. Cheng. 2001. “Strengthening of unreinforced masonry walls using FRPs.” J. Compos. Constr. 5 (2): 76–84. https://doi.org/10.1061/(ASCE)1090-0268(2001)5:2(76).
AS (Australia Standards). 2009. Concrete structures. AS 3600. Sydney, Australia: AS.
Cardoso, R. 2018a. “Haussmann structural floors repairs and strengthening techniques.” J. Sustainable Archit. Civ. Eng. 23 (2): 16–24. https://doi.org/10.5755/j01.sace.23.2.21426.
Cardoso, R. 2018b. “Paris Haussmann building underpinning: A study case.” Acta Technica Napocensis: Civ. Eng. Archit. 61 (2): 40–49.
Cardoso, R. 2019. “Deep beams reinforcement, national and Eurocode 2 design provisions.” Ann. Faculty Eng. Hunedoara Int. J. Eng. 17 (1): 37–44.
Cardoso, R., A. Paiva, J. Pinto, and J. C. Lanzinha. 2018. “Structural and material characterization of a Haussmann building.” Urbanism Archit. Constr. 9 (4): 347–356.
Cardoso, R., A. Paiva, J. Pinto, and J. C. Lanzinha. 2019. “Structural and material characterization of a Haussmann building complex at La Madeleine, Paris. The first step before sustainable rehabilitation and strengthening.” J. WSEAS Trans. Environ. Dev. 15 (2): 14–21.
Cardoso, R., J. Pinto, A. Paiva, and J. C. Lanzinha. 2016. “Characterization of tabique walls nails of the Alto Douro Wine Region.” Open Eng. 6 (1): 446–454. https://doi.org/10.1515/eng-2016-0064.
CEN (European Committee for Standardization). 2004. Design of concrete structures. 1–1: General rules and rules for buildings. Eurocode 2 EN 1992-1-1. Brussels, Belgium: CEN.
CEN (European Committee for Standardization). 2005. Design of masonry structures. 1.1: General rules for reinforced and unreinforced masonry structures. Eurocode 6 EN 1996-1-1. Brussels, Belgium: CEN.
Costa, A., J. Miranda Guedes, and H. Varum. 2013. Structural rehabilitation of old buildings. Berlin: Springer.
CSA (Canadian Standards Association). 2004. Design of concrete structures. CAN/CSA-A23.3. Mississauga, ON, Canada: CSA.
Delatte, N. 2009. Failure, distress and repair of concrete structures. Cambridge, UK: Woodhead.
Doh, J. H., and S. Fragomeni. 2015. “Evaluation of experimental work on concrete walls in one-way and two-way action.” Aust. J. Struct. Eng. 6 (1): 37–52. https://doi.org/10.1080/13287982.2005.11464943.
Engel, P. 2019. “General rehabilitation techniques using steel.” Accessed January 31, 2019. http://www.constructalia.com/english/renovation_with_steel/ii_general_rehabilitation_techniques_using_steel#.VMPsNP6G9Wg.
Fragomeni, S., J. H. Doh, and D. J. Lee. 2012. “Behavior of axially loaded concrete wall panels with openings: An experimental study.” Adv. Struct. Eng. 15 (8): 1345–1358. https://doi.org/10.1260/1369-4332.15.8.1345.
Fragomeni, S., and P. Mendis. 1997. “Instability analysis of normal- and high-strength reinforced-concrete walls.” J. Struct. Eng. 123 (5): 680–684. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:5(680).
Lee, D. J. 2008. “Experimental and theoretical study of normal and high strength concrete wall panels with openings.” Ph.D. thesis, Griffith School of Engineering, Science, Environment, Engineering and Technology, Griffith Univ.
Li, B., and C. Lim. 2010. “Tests on seismically damaged reinforced concrete structural walls repaired using fiber-reinforced polymers.” J. Compos. Constr. 14 (5): 597–608. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000110.
Mohammed, B., L. W. Ean, and M. A. Malek. 2013. “One way RC wall panels with openings strengthened with CFRP.” Constr. Build. Mater. 40 (Mar): 575–583. https://doi.org/10.1016/j.conbuildmat.2012.11.080.
Popescu, C. 2015. “FRP strengthening of concrete walls with openings.” Ph.D. thesis, Dept. of Civil, Environmental and Natural Resources Engineering, Luleå Univ. of Technology.
Popescu, C., G. Sas, T. Blanksvärd, and B. Täljsten. 2015. “Concrete walls weakened by openings as compression members: A review.” Eng. Struct. 89 (Apr): 172–190. https://doi.org/10.1016/j.engstruct.2015.02.006.
Saheb, S. M., and P. Desayi. 1990. “Ultimate strength of RC wall panels with openings.” J. Struct. Eng. 16 (6): 1565–1577. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:6(1565).
Seddon, A. E. 1956. “The strength of concrete walls under axial and eccentric loads.” In Proc., Symp. on Strength of Concrete Structures, edited by R. P. Andrew, 445–486. London: Cement and Concrete Association.
Todut, C., D. Dan, and V. Stoian. 2015. “Numerical and experimental investigation on seismically damaged reinforced concrete wall panels retrofitted with FRP composites.” Compos. Struct. 119 (Jan): 648–665. https://doi.org/10.1016/j.compstruct.2014.09.047.
Triantafillou, T. C., and C. G. Papanicolaou. 2006. “Shear strengthening of reinforced concrete members with textile reinforced mortar (TRM) jackets.” Mater. Struct. 39: 93–103. https://doi.org/10.1007/s11527-005-9034-3.
Zhao, K. Z., and Y. Han. 2013. “Discussion of the masonry structure building underpinning method.” In Vol. 351–352 of Applied Mechanics and Materials, 471–475. Switzerland: Trans Tech Publications. https://doi.org/10.4028/www.scientific.net/AMM.351-352.471.
Information & Authors
Information
Published In
Practice Periodical on Structural Design and Construction
Volume 25 • Issue 2 • May 2020
Copyright
©2020 American Society of Civil Engineers.
History
Received: Apr 20, 2019
Accepted: Oct 30, 2019
Published online: Feb 26, 2020
Published in print: May 1, 2020
Discussion open until: Jul 26, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.