Abstract
Today, the use of composite sections of concrete and steel is increasing. In this study, the behavior of two partially encased composite (PEC) columns is studied experimentally under pure compressive and bending loads. Then a simple analytical method is suggested for PEC columns by introducing all-steel columns, which are composed of four stiffener plates on the four flanges of the steel section. The sizes of the stiffener plates are found by equalizing the compressing strength as well as bending stiffness of the two sections. The accuracy and efficiency of the suggested method was assessed using the FEM in a software program by calculating and comparing the internal forces resulting from analyzing an irregular building. The results indicated high accuracy of the suggested linear static analysis method and meet the need to use finite-element simulations for the users and designers.
Get full access to this article
View all available purchase options and get full access to this article.
References
Abaqus v 6.14.2 [Computer software]. SIMULIA, Providence, RI.
ACI (American Concrete Institute). (1997). “State-of-the-art report on high-strength concrete (reapproved in 1997).” ACI 363R-92, Farmington Hills, MI.
ACI (American Concrete Institute). (2008). “Building code requirements for structural concrete and commentary.” ACI 318R-08, Farmington Hills, MI.
ANSYS 18.2 [Computer software]. ANSYS, Canonsburg, PA.
ASTM. (2003). “Standard test methods and definitions for mechanical testing of steel products,” West Conshohocken, PA.
Begum, M., Driver, R., and Elwi, A. (2007). “Finite-element modeling of partially encased composite columns using the dynamic explicit method.” J. Struct. Eng., 326–334.
Begum, M., Driver, R. G., and Elwi, A. E. (2013). “Behaviour of partially encased composite columns with high strength concrete.” Eng. Struct., 56(Nov), 1718–1727.
Begum, M., Driver, R. G., and Elwi, A. E. (2015). “Parametric study on eccentrically-loaded partially encased composite columns under major axis bending.” Steel Compos. Struct., 19(5), 1299–1319.
Begum, M., and Ghosh, D. (2014). “Simulations of PEC columns with equivalent steel section under gravity loading.” Steel Compos. Struct., 16(3), 305–323.
CEN (European Committee for Standardization). (2004). Eurocode 4: Design of composite steel and concrete structures, part 1-1: General rules and rules for buildings, Brussels, Belgium.
Chen, Y., Wang, T., Yang, J., and Zhao, X. (2010). “Test and numerical simulation of partially encased composite columns subject to axial and cyclic horizontal loads.” Int. J. Steel Struct., 10(4), 385–393.
Chicoine, T., Massicotte, B., and Tremblay, R. (2002a). “Finite element modelling and design of partially encased composite columns.” Steel Compos. Struct., 2(3), 171–194.
Chicoine, T., Tremblay, R., Massicotte, B., Ricles, J., and Lu, L. (2002b). “Behavior and strength of partially encased composite columns with built up shapes.” J. Struct. Eng., 279–288.
CSA (Canadian Standards Association). (2014). “Limit states design of steel structures.” S16–14, Mississauga, ON, Canada.
Dastfan, M., and Driver, R. (2016). “Large-scale test of a modular steel plate shear wall with partially encased composite columns.” J. Struct. Eng., 04015142.
Ebadi Jamkhaneh, M., and Kafi, M. A. (2017). “Experimental and numerical investigation of octagonal partially encased composite columns subject to axial and torsion moment loading.” Civil Eng. J., 3(10), 939–955.
Hsu, L. S., and Hsu, C. T. T. (1994). “Complete stress-strain behaviour of high-strength concrete under compression.” Mag. Concr. Res., 46(169), 301–312.
Marinopoulou, A. A., Balopoulos, V. D., and Kalfas, C. N. (2007). “Simulation of partially encased composite steel–concrete columns with steel columns.” J. Constr. Steel Res., 63(8), 1058–1065.
Nayal, R., and Rasheed, H. (2006). “Tension stiffening model for concrete beams reinforced with steel and FRP bars.” J. Mater. Civ. Eng., 831–841.
Oyawa, W. O., Gathimba, N. K., and Mang’uriu, G. N. (2016). “Structural response of composite concrete filled plastic tubes in compression.” Steel Compos. Struct., 21(3), 589–604.
Pereira, F. M., De Nardin, S., and El Debs, L. H. C. (2016). “Structural behavior of partially encased composite columns under axial loads.” Steel Compos. Struct., 20(6), 1305–1322.
SAP 19.0.0 [Computer software]. Computers & Structures, Inc., Walnut Creek, CA.
Song, Y. C., Wang, R. P., and Li, J. (2016). “Local and post-local buckling behavior of welded steel shapes in partially encased composite columns.” Thin Walled Struct., 108(Nov), 93–108.
Zhao, G. T., and Feng, C. (2012). “Axial ultimate capacity of partially encased composite columns.” Appl Mech. Mater., 166–169, 292–295.
Information & Authors
Information
Published In
Copyright
© 2018 American Society of Civil Engineers.
History
Received: Oct 5, 2017
Accepted: Dec 14, 2017
Published online: Apr 13, 2018
Published in print: Aug 1, 2018
Discussion open until: Sep 13, 2018
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.