Abstract
This article presents a multihazard-resistant panelized brick veneer with steel stud backup (PBVSS) system capable of being developed off-site with fiber-reinforced polymer (FRP) enhancements. This study is a continuation of two previous studies of PBVSS systems developed at Pennsylvania State University in the Building Components and Envelopes Research Laboratory (BCERL). The specimens used in this study include one control specimen. Two types of composites were used, glass fiber-reinforced polymer (GFRP) and spray polyurea, with three composite configurations. Experimental data obtained from a uniformly applied pressure through an air bladder with expected boundary conditions were collected. The measured test data provided a basis for evaluating the performance and capacity of the PBVSS, particularly the veneer portion. A comparison of specimen test results shows that the FRP enhancements on the interior side of brick veneer provide additional veneer capacity. Beyond the performance of the veneer, the study shows that it is indeed possible to reinforce the interior side of a brick veneer surface if it is constructed in panelized segments in a factory setting.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Partial funding for this study was provided by the National Science Foundation (NSF) under Grant CMMI-0653985. The support from NSF is gratefully acknowledged. Any opinions expressed here are those of the authors and do not necessarily represent those of the NSF.
References
ASCE. (2011). “Blast protection of buildings.” ASCE 59-11, Reston, VA.
ASTM. (2005). “Standard test methods of conducting strength tests of panels for building construction.” E72-05, West Conshohocken, PA.
Bangash, M. Y. T., and Bangesh, T. (2006). Explosion-resistant buildings, Springer, Berlin.
BIA (Brick Industry Association). (1999). “Brick veneer/steel stud walls.” Technical Notes on Brick Construction, Reston, VA.
BIA (Brick Industry Association). (2005). “Revised brick veneer/steel stud walls.” Technical Notes on Brick Construction, Reston, VA.
Carney, P., and Myers, J. J. (2003). “Out-of-plane static and blast resistance of unreinforced masonry wall connections strengthened with FRP.” Rep. 03-46, Center for Infrastructure Engineering Studies, Univ. of Missouri, Rolla, MO.
Carney, P., and Myers, J. J. (2005). “SP-230-14: Out-of-plane static and blast resistance of unreinforced masonry wall connections strengthened with FRP.” 7th Int. Symp. on Fiber-Reinforced (FRP) Polymer Reinforcement for Concrete Structures, American Concrete Institute, Farmington Hills, MI.
Crawford, J. E. (2005). Protective designs for blast and impact threats, Karagozian & Case, Pasadena, CA.
Dusenberry, D. O. (2005). “A new standard for blast protection of buildings.” Proc., Metropolis and Beyond,” ASCE, Reston, VA, 6.
FEMA (2003). FEMA 27:Primer for design of commercial buildings to mitigate terrorists attacks, Washington, DC.
Hrynyk, T. D. (2007). “Static evaluation of the out-of-plane behavior of URM infill walls utilizing modern blast retrofit techniques.” M.Sc. thesis, Univ. of Missouri, Rolla, MO.
Krauthammer, T. (2008). “Behaviors of structural elements.” Modern protective structures, CRC Press, Boca Raton, FL, 195–236.
Kuczynski, T. C. (2009). “Experimental investigation of multihazard resistant panelized brick veneer on steel stud wall system for out-of-plane failure loading.” M.S. thesis, Dept. of Architectural Engineering, Pennsylvania State Univ., University Park, PA.
Kuczynski, T. C., and Memari, A. M. (2012). “Experimental evaluation of the enhanced panelized brick veneer over steel stud wall system for out-of-plane loading.” Mater. Struct., 46(5), 1–18.
Liang, J. (2006). “Development of a multihazard resistant panelized brick veneer wall system.” Ph.D. dissertation, Dept. of Architectural Engineering, Pennsylvania State Univ., University Park, PA.
Liang, J., and Memari, A. M. (2011). “Introduction of a panelized brick veneer wall system and its building science evaluation.” J. Archit. Eng., 1–14.
Liang, J., and Memari, A. M. (2012). “Performance of a panelized brick veneer wall system under lateral loads.” Open J. Civil Eng., 2, 132–146.
Rafiq, M. Y. (1989). “Estimating structural components resistance to blast loading using laboratory static tests.” Proc. Struct. Shock Impact, 4, 39–48.
Salim, H., Dinan, R., Kiger, S. A., Townsend, P. T., and Shull, J. (2003). “Blast-retrofit wall systems using cold-formed steel studs.” Proc., 16th ASCE Engineering Mechanics Conf., ASCE, Reston, VA, 11.
Salim, H., Dinan, R., and Townsend, P. T. (2005). “Analysis and experimental evaluation of in-fill steel-stud wall systems under blast loading.” J. Struct. Eng., 1216–1225.
Schmidt, J. A. (2006). “Blast protection of buildings: Design criteria and loadings.” Structures Congress 2006: Structural Engineering and Public Safety, ASCE, Reston, VA, 6.
Stallworth, H. L. (2011). “Flexural behavior of a reinforced brick veneer over steel studs wall panel system.” M.S. thesis, Dept. of Architectural Engineering, Pennsylvania State Univ., University Park, PA.
Tan, K. H., and Patoary, M. K. H. (2004). “Strengthening of masonry walls against out-of-plane loads using fiber-reinforced polymer reinforcement.” J. Compos. Constr., 79–87.
Information & Authors
Information
Published In
Copyright
© 2016 American Society of Civil Engineers.
History
Received: Jun 22, 2015
Accepted: Sep 29, 2015
Published online: Mar 3, 2016
Discussion open until: Aug 3, 2016
Published in print: Nov 1, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.