Abstract
Pile bent bridges are a frequently chosen solution for stream crossings in the New Madrid Seismic Zone (NMSZ). Ease of construction makes the pile bent bridge a favorable choice in challenging subsurface conditions. When seismic loading requires conventionally constructed pile bents to behave in an inelastic fashion, the wall thickness of unfilled steel pipe piles necessary to preclude local buckling virtually doubles relative to that required if the piles remain elastic. Partial isolation—in which isolators are located at the piers with the abutments constructed integrally—is proposed as a strategy deserving of consideration for such situations. If piling can be designed to remain elastic, then the savings in material costs will, at least partially, offset the cost of isolation bearings. Along with isolator displacement demands, the yield strength necessary to keep the piles in the elastic range is a key parameter to be determined.
Get full access to this article
View all available purchase options and get full access to this article.
References
AASHTO. (2011). Guide specifications for LRFD seismic bridge design, 2nd Ed., Washington, DC.
AASHTO. (2014a). AASHTO LRFD bridge design specifications, Washington, DC.
AASHTO. (2014b). Guide specifications for seismic isolation design, 4th Ed., Washington, DC.
Angelopoulou, D. (2009). Seismic response analysis of multi-span isolated bridges, The University of Patras, Patras, Greece.
Buckle, I., Constantinou, M., Dicleli, M., and Ghasemi, H. (2006). “Seismic isolation of highway bridges.” MCEER-06-SP07, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, NY.
Cardone, D., Dolce, M., Matera, F., and Palermo, G. (2008). Application of direct displacement based design to multi-span simply supported deck bridges with seismic isolation: A case study, International Association for Earthquake Engineering, Beijing, pp. 1–8.
Casarotti, C. (2004). Bridge isolation and dissipation devices, European School for Advanced Studies in Reduction of Seismic Risk (ROSE School), Pavia, Italy.
Christopoulos, C., and Filiatrault, A. (2006). Principles of passive supplemental damping and seismic isolation, IUSS Press, Pavia, Italy.
Computers and Structures, Inc., (2014). CSiBridge version 17, Berkely, CA. (Computer software).
Dimitriadou, O., (May 2007). Effect of isolation on bridge seismic design and response, European School for Advanced Studies in Reuction of Seismic Risk (ROSE School), Pavia, Italy.
FIP Industriale. (2011). Lead rubber bearings product catalog, Selvazanno, Italy.
Gulkan, P., and Sozen, M. A. (1974). “Inelastic response of reinforced concrete structure to earthquake motions.” J. Am. Concr. Inst., 71(12), 604–610.
Hu, W. (2008). “Analysis of effectiveness of bridges with partial isolation.” Master’s thesis, Utah State University, School of Graduate Studies, Logan, UT.
Kawashima, K. (2004). “Seismic isolation of highway bridges.” J. Jpn. Assoc. Earthquake Eng., 4(3), 283–297.
Liao, W. I., Loh, C. H., and Wan, S. (2000). Responses of isolated bridges to near-fault ground motions recorded in chi chi earthquake. National Center for Research in Earthquake Engineering, Taipei, Taiwan, pp. 371–380.
Maurer Söhne. (2011). Seismic isolation systems with lead rubber bearings, Munich, Germany.
Mosqueda, G., Whittaker, A. S., Fenves, G. L., and Mahin, S. A. (2004). Experimental and analytical studies of the friction pendulum system for the seismic protection of simple bridges, Earthquake Engineering Research Center, Berkeley, CA.
Nagarajaiah, S., Reinhorn, A. M., and Constantinou, M. C. (1991). “3D-basis: Nonlinear dynamic analysis of three-dimensional base isolated structures: Part II.” Technical Rep. NCEER-91-0005, National Center for Earthquake Engineering Research, State Univ. of New York, Buffalo, NY.
NEHRP Consultants Joint Venture. (2011). “Selecting and scaling earthquake ground motions for performing response history analysis.” NIST GCR 11-917-15, National Institute of Standards and Technology, Gaithersburg, MD.
PEER (Pacific Earthquake Engineering Research Center). (2011). PEER Ground Motion Database 〈http://peer.berkeley.edu/peer_ground_motion_database〉, (July 9, 2012).
PEER (Pacific Earthquake Engineering Research Center). (2014). PEER Ground Motion Database. 〈http://ngawest2.berkeley.edu/〉 (Nov. 11, 2015).
Pietra, G. M., Calvi, G. M., and Pinho, R. (2008). “Displacement-based seismic design of isolated bridges.” Research Rep. ROSE-2008/01, 1st Ed., IUSS Press, Pavia, Italy.
Priestley, M. J. N., Calvi, G. M., and Kowalsky, M. J. (2007). Displacement-based seismic design of structures, IUSS Press, Pavia, Italy.
Priestley, M. J. N., and Grant, D. N. (2005). “Viscous damping in seismic design and analysis.” J. Earthquake Eng., 9(2), 229–255.
Priestley, M. J. N., Seible, F., and Calvi, G. M. (1996). Seismic design and retrofit of bridges, Wiley Interscience, New York.
Robinson Seismic LTD. (2011). Catalog of Robinson Seismic Bearings, Petone, New Zealand.
SeismoArtif 2.1.0 [Computer software]. SeismoSoft, Pavia, Italy.
SeismoMatch 2.1.0 [Computer software]. SeismoSoft, Pavia, Italy.
Skinner, R. I., Robinson, W. H., and McVerry, G. H. (1993). An introduction to seismic isolation, Wiley and Sons, Chichester, England.
Stewart, Jonathan P., et al. (2011). “Representation of bidirectional ground motions for design spectra in building codes.” Earthquake Spectra, 27(3), 927–937.
USGS (United States Geological Survey). (2002). 2002 Interactive Deaggregations 〈http://geohazards.usgs.gov/deaggint/2002/〉
USGS (United States Geological Survey). (2008). 2008 Interactive Deaggregations 〈https://geohazards.usgs.gov/deaggint/2008/〉
USGS and California Geological Survey, (2011). Center for Engineering Strong Motion Data 〈http://www.strongmotioncenter.org/vdc/scripts/default.plx〉
Wang, Y.-P., Chung, L.-L., and Liao, W.-H. (1998). “Seismic response analysis of bridges isolated with friction pendulum bearings.” Earthquake Eng. Struct. Dyn., 27(10), 1069–1093.
Warn, G. P., and Whittaker, A. S. (2007). “Performance estimates for seismically isolated bridges.” MCEER-07-0024, Multidisciplinary Center for Earthquake Engineering Research, Buffalo, NY.
Watson-Lamprey, J. A., and Boore, D. M. (2007). “Beyond SA-GMRotI: Conversion to SA-Arb, SA-SN, and SA-MaxRot.” Bull. Seismol. Soc. Am., 97(5), 1511–1524.
Wen, Y. K. (1976). “Method for random vibration of hysteretic systems.” J. Engrg. Mech. Div., ASCE, Vol. 102(2), 249–263.
Information & Authors
Information
Published In
Copyright
© 2015 American Society of Civil Engineers.
History
Received: Jul 7, 2015
Accepted: Sep 29, 2015
Published online: Dec 30, 2015
Published in print: May 1, 2016
Discussion open until: May 30, 2016
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.