Investigation of Cold Rolled Steel Gusset Plates under Cycling Load When Varying the Unsupported Length–Thickness Ratio
Publication: Practice Periodical on Structural Design and Construction
Volume 17, Issue 2
Abstract
This article is an investigation of buckling of cold-rolled gusset plates subjected to cyclic axial load for various unsupported length-to-thickness ratios (). A total of twelve specimens were tested and their respective time-to-failure (in terms of the number of cycles) were measured. Using the data obtained, the dependence of time-to-failure on the ratio was investigated. The dependence of time-to-failure on the ratio is important and can be rationalized via an equation through analyses and test results. Such an equation will especially be helpful in design and can be used, along with other requirements, for the selection of an appropriate size for a gusset plate. The paper draws conclusions based on the limited test results and discusses the importance of and cyclic loads in design of gusset plates in bridges.
Get full access to this article
View all available purchase options and get full access to this article.
References
Casafont, M., Arnedo, A., Roure, F., and Rodríguez-Ferrán, A. (2007). “Experimental testing of joints for seismic design of lightweight structures. Part 3: Gussets, corner joints, -braced frames.” Thin-Walled Struct.TWASDE, 45(7–8), 637–659.
Castelblanco, C., Uribe, N., and Nuñez, F. (2009). “Study of the unsupported length-thickness ratio in steel gusset plates when loaded with axial cycling loads.” B.Sc. thesis, Dept. of Civil Engineering, Pontificia Universidad Javeriana, Bogotá-Colombia.
Chakrabarti, S., and Bjorhovde, R. (1983). “Tests of full size gusset plate connections.” Research Rep., Dept. of Civil Engineering, Univ. of Arizona-Tucson, Tuscon, AZ.
Davis, C. (1967). “Computer analysis of stresses in gusset plates.” M.Sc. thesis, Univ. of Washington, Seattle, WA.
Gross, J. L. (1990). “Experimental study of gusseted connections.” AISC Eng. J., 27(3), 89–97.
Hu, S., and Cheng, J. (1987). “Compressive behavior of gusset plate connections.” Structural Engineering Rep. No. 153, Dept. of Civil Engineering. Univ. of Alberta, Edmonton, AB.
Thornton, W. A. (1984). “Bracing connections for heavy construction.” AISC Eng. J., 21(3), 139–148.
Tung-Ming, W. (1958). “Investigation of the Bauschinger effect in metals.” M.S. thesis, Massachusetts Institute of Technology, Cambridge, MA.
Varsarelyi, D. D. (1971). “Tests of gusset plates models.” J. Struct. Div.JSDEAG, 97(2), 665–678.
Walbride, S., Grondin, G., and Cheng, R. (1998). “An analysis of the cyclic behavior of steel gusset plate connections.” Structural Engineering Rep. No. 225, Univ. of Alberta, Edmonton, AB, Canada.
Whitmore, R. (1952). “Experimental investigation of stresses in gusset plates.” Bulletin No. 16 Engineering Experiment Station, Univ. of Tennessee, Knoxville, TN.
Williams, G., and Richard, R. (1986). “Steel connection design based on inelastic finite element analysis.” Rep. of the Dept. of Civil Engineering And Engineering Mechanics, The Univ. of Arizona, Tuscon, AZ.
Yam, M., and Cheng, R. (1993). “Experimental investigation of the compressive behavior of gusset plate connections.” Structural Engineering Rep. No. 194, Univ. of Alberta, Edmonton, AB, Canada.
Information & Authors
Information
Published In
Copyright
© 2012. American Society of Civil Engineers.
History
Received: Dec 14, 2009
Accepted: Jun 9, 2011
Published online: Jun 14, 2011
Published in print: May 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.