Development of a Model for Estimation of Buried Large-Diameter Thin-Walled Steel Pipe Deflection due to External Loads
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 10, Issue 3
Abstract
Diameters and wall thicknesses of flexible pipes are usually designed as per hydraulic requirements, such as flow capacity, internal fluid pressure, and pipe material properties. Proper embedment is then designed to protect the pipe integrity against external loads. This paper considered engineering properties of embedment soils in analysis of flexible pipe–soil system for external load conditions and a new model was developed for the prediction of deflection of flexible steel pipe. Full-scale laboratory tests were performed to develop the new model and finite-element models were analyzed to validate the test results. In this research, the finite-element method was effectively used to model the soil–pipe interaction for five full-scale laboratory tests conducted on a steel pipe. Such models can be used for analysis of flexible pipe embedment design for layered embedment conditions. The results of finite-element analysis showed that the squaring of the pipe occurs when the haunch soil is weak compared to the side column. Another critical observation made during the tests was that the stresses at the bottom of the pipe and the bedding angle are highly dependent on haunch soil strength. It is desirable that the stress due to surcharge load on top of the pipe, weight of the pipe, and water inside the pipe be distributed uniformly across the width of the bedding.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors greatly acknowledge funding support from Tarrant Regional Water District (TRWD) for carrying out this research. Also, appreciation goes to the Integrated Pipeline (IPL) Project management team, AECOM, and the Department of Civil Engineering, University of Texas at Arlington, for extending every possible help to make this work possible.
References
AASHTO. 2017. The standard method of test for moisture-density relations of soils using a 4.54-kg (10-lb) rammer and a 457- mm (18-in.) drop. AASHTO T 180. Washington, DC: AASHTO.
AWWA (American Water Works Association). 2006. PE pipe: Design and installation, first edition. AWWA M55. Denver: AWWA.
AWWA (American Water Works Association). 2009. Ductile-iron pipe and fittings, third edition. AWWA M41. Denver: AWWA.
AWWA (American Water Works Association). 2013. Fiberglass pipe design, third edition. AWWA M45. Denver: AWWA.
AWWA (American Water Works Association). 2017. Steel pipe: A guide for design and installation, fifth Edition. AWWA M11. Denver: AWWA.
Bryden, P., H. El Naggar, and A. Valsangkar. 2015. “Soil-structure interaction of very flexible pipes: Centrifuge and numerical investigations.” Int. J. Geomech. 15 (6): 04014091. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000442.
Dezfooli, M. S., A. Abolmaali, and M. Razavi. 2015. “Coupled nonlinear finite-element analysis soil–steel pipe structure interaction.” Int. J. Geomech. 15 (1): 04014032. https://doi.org/10.1061/(ASCE)GM.1943-5622.0000387.
Drucker, D. C., and W. Prager. 1952. “Soil mechanics and plastic analysis or limit design.” Quart. Appl. Math. 10 (2): 157–165. https://doi.org/10.1090/qam/48291.
Duncan, J. M., P. Byrne, K. S. Wong, and P. Marby. 1980. Strength, stress-strain and bulk modulus parameters for finite element analysis of stresses and movements in soil masses. Berkeley, CA: Univ. of California.
Elshimi, T. M., and I. D. Moore. 2013. “Modeling the effects of backfilling and soil compaction beside shallow buried pipes.” J. Pipeline Syst. Eng. Pract. 4 (4): 04013004. https://doi.org/10.1061/(ASCE)PS.1949-1204.0000136.
Hartley, J. D., and J. M. Duncan. 1987. “ and its variation with depth.” J. Transp. Eng. 113 (5): 538–553. https://doi.org/10.1061/(ASCE)0733-947X(1987)113:5(538).
Howard, A. K. 1977. “Modulus of soil reaction values for buried flexible pipe.” J. Geotech. Eng. Div. 103 (1): 33–43.
Howard, A. K. 2006. “The reclamation E′ table, 25 years later.” In Proc., Plastics Pipe XIII International Conf. Lakewood, CO: Amster Howard.
Hsieh, P. G., C. Y. Ou, and A. Lim. 2010. “Use of the total stress undrained model to the analysis of deep excavation.” In Proc., of the 17th Southeast Asian Geotechnical Conf. Taipei, Taiwan: Taipei International Convention Center.
Kawabata, T., Y. Mohri, H. Tamura, D. Shoda, and T. Oda. 2006. “Field test for buried large steel pipes with thin wall.” In Proc., ASCE Pipelines 2006: Service to the Owner, 1–8. Reston, VA: ASCE.
Logan, D. 2012. A first course in finite element analysis. Stamford, CT: Global Engineering.
Marston, A., and A. O. Anderson. 1913. The theory of loads on pipes in ditches and tests of cement and clay drain tile and sewer pipe. Bulletin 31, Engineering Experiment Station. Ames, IA: Iowa State College of Agriculture and Mechanic Arts.
Moser, A. P. 2001. Buried pipe design. 3rd ed. New York: McGraw-Hill.
PLAXIS. 2012. “PLAXIS 2D reference manual.” Accessed March 3, 2012. https://www.plaxis.com/support/models/plaxis-user-defined-soil-models/.
Popa, H., and L. Batali. 2010. “Finite element method in geotechnical design. soil constitutive laws and calibration of the parameters. Retaining wall case study.” WSEAS Trans. Appl. Theor. Mech. 5 (3): 177–186.
Roscoe, K. H., and J. B. Burland. 1968. “On the generalized stress–Strain behavior of ‘wet clay.’” In Engineering plasticity, edited by J. Heyman and F. A. Leckie, 535–609. Cambridge, UK: Cambridge University Press.
Roscoe, K. H., A. N. Schofield, and A. Thurairajah. 1963. “Yielding of clays in states wetter than critical.” Géotechnique 13 (3): 211–240. https://doi.org/10.1680/geot.1963.13.3.211.
Schanz, T., P. A. Vermeer, and P. G. Bonnier. 1999. “The hardening soil model: Formulation and Verification.” In Beyond 2000 in computational geotechnics–10 years of PLAXIS. Rotterdam, Netherlands: A.A. Balkema.
Sharma, J. R. 2013. “Development of a model for estimation of buried large diameter thin-walled steel pipe deflection due to external loads.” Ph.D. dissertation, Dept. of Civil Engineering, Univ. of Texas at Arlington.
Sharma, J. R., M. Najafi, D. Marshall, and A. Jain. 2012. “Evaluation of statically-loaded large diameter steel pipe embedded with lime stabilized native clay soils.” In Proc., ASCE Pipelines 2012: Innovations in Design, Construction, Operations, and Maintenance, Doing More with Less, 242–256. Reston, VA: ASCE.
Sharma, J. R., M. Najafi, D. Marshall, and A. Jain. 2013. “Thin-walled, large-diameter steel pipe response to various embedment conditions.” In Proc., ASCE Pipelines 2013: Pipelines and Trenchless Construction and Renewals—A Global Perspective, 1419–1431. Reston, VA: ASCE.
Sharma, J. R., M. Najafi, D. Marshall, A. Jain, and S. Rahjoo. 2011. “Testing and evaluation of statically-loaded large diameter steel pipe with native backfill soils.” In Proc., ASCE Pipelines 2011: A Sound Conduit for Sharing Solutions, 1025–1034. Reston, VA: ASCE.
Spangler, M. G. 1941. The structural design of flexible pipe culverts. Bulletin, XL (153). Ames, IA: Iowa State College.
Vermeer, P. 1982. “A five constant model unifying well established concepts.” In Proc., Int. Workshop on Constitutive Behavior of Soils, 175–197. Roterdam, Balkema.
Webb, M. C., D. D. P. Trebicki, and P. A. Smulders. 2002. “Field testing and buckling strength of buried large-diameter thin-walled steel pipes.” In Proc., ASCE Pipelines 2002: Beneath Our Feet: Challenges and Solutions, 69–10. Reston, VA: ASCE.
Information & Authors
Information
Published In
Copyright
©2019 American Society of Civil Engineers.
History
Received: Oct 9, 2017
Accepted: Dec 6, 2018
Published online: Apr 30, 2019
Published in print: Aug 1, 2019
Discussion open until: Sep 30, 2019
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.