Occurrence of Naturally Shaped Lenticular Bed Deposit and Its Influence on the Frictional Pressure Drop during Pipeline Transportation of Low Concentration Slurries
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 6, Issue 2
Abstract
Solid particles can be transported along a pipeline in the form of trains of individually shaped lenticular deposits (LDs) when the concentration of solids is less than 1 vol% and the transport velocity is below the critical value required for full suspension. Such special bed transport, observed as rippled sand dune patterns, may occur in petroleum production lines transporting oil and gas produced from unconsolidated sand reservoirs under turbulent flow conditions, and during sediment transport by rivers and winds. The primary objective of this study was to investigate how the occurrence of lenticular bed deposits affects near-wall turbulent activities at the sand/fluid (“wave-like”) interface and frictional pressure drop during pipeline transportation of solids. Particle image velocimetry (PIV) measurements were used to quantify the velocity field, the turbulence kinetic energy (TKE), and the coherent structures associated with surface morphology change and LD formation near the bed deposits/fluid interface. A 7–8% reduction in frictional pressure drop was consistently observed during the transition from continuous sand bed to LDs. Results also indicate that the formation of naturally shaped LDs reduces the intensity and frequency of near-wall turbulent coherent structures (burst-sweep events). Moreover, TKE associated with flow over the LDs was found to be lower than that of continuous bed and water (only) flow.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
Financial support from the Canada Foundation for Innovation (CFI) and the Natural Science and Engineering Research Council of Canada (NSERC), which made possible the construction of the multipurpose experimental facilities, is gratefully acknowledged.
References
Aleyev, Y. G. (1977). Nekton, Dr. W. Junk Publishers, The Hague, Netherlands.
Bechert, D. W., Bruse, M., Hage, W., Van der Hoeven, J. G. T., and Hoppe, G. (1997). “Experiments on drag-reducing surfaces and their optimization with an adjustable geometry.” J. Fluid Mech., 338, 59–87.
Best, J. (2005a). “Kinematics, topology and significance of dune-related macroturbulence: Some observations from the laboratory and field.” Fluvial sedimentology VII, M. D. Blum, S. B. Marriott, and S. F. Leclair, eds., Blackwell Publishing, Oxford, U.K.
Best, J. (2005b). “The fluid dynamics of river dunes: A review and some future research directions.” J. Geophys. Res., 110(21), 1–21.
Blackwelder, R. F., and Kaplan, R. E. (1976). “On the wall structure of the turbulent boundary layer.” J. Fluid Mech., 76(1), 89–112.
Bogard, D. G., and Tiederman, W. G. (1986). “Burst detection with single-point velocity measurements.” J. Fluid Mech., 162, 389–413.
Brodkey, R. S., Wallace, J. M., and Eckelmann, H. (1974). “Some properties of truncated turbulence signals in bounded shear flows.” J. Fluid Mech., 63(2), 209–224.
Bushnell, D. M., and Moore, K. J. (1991). “Drag reduction in nature.” Annu. Rev. Fluid Mech., 23(1), 65–79.
Choi, K.-S., and Graham, M. (1998). “Drag reduction of turbulent pipe flows by circular-wall oscillation.” Phys. Fluids, 10(1), 7–9.
Churchill, S. W. (1977). “Frictional equation spans all fluid flow regimes.” Chem. Eng., 84(24), 91–92.
Corino, E. R., and Brodkey, R. S. (1969). “A visual investigation of the wall region in turbulent flow.” J. Fluid Mech., 37(1), 1–30.
Dean, B., and Bhushan, B. (2010). “Shark-skin surfaces for fluid-drag reduction in turbulent flow: A review.” Philos. Trans. R. Soc. A: Math. Phys. Eng. Sci., 368(1929), 4775–4806.
Eisfeld, B., and Schnitzlein, K. (2001). “The influence of confining walls on the pressure drop in packed beds.” Chem. Eng. Sci., 56(14), 4321–4329.
Howard, F. G., and Goodman, W. L. (1985). “Axisymmetric bluff-body drag reduction through geometrical modification.” J. Aircr., 22(6), 516–522.
Karniadakis, G. E., and Choi, K.-S. (2003). “Mechanisms on transverse motions in turbulent wall flows.” Annu. Rev. Fluid Mech., 35(1), 45–62.
Kiml, R., Magda, A., Mochizuki, S., and Murata, A. (2004). “Rib-induced secondary flow effects on local circumferential heat transfer distribution inside a circular rib-roughened tube.” Int. J. Heat Mass Transfer, 47(6–7), 1403–1412.
Kline, S. J., Reynolds, W. C., Schraub, F. A., and Runstadler, P. W. (1967). “The structure of turbulent boundary layers.” J. Fluid Mech., 30(4), 741–773.
Lu, S. S., and Willmarth, W. W. (1973). “Measurements of the structure of the Reynolds stress in a turbulent boundary layer.” J. Fluid Mech., 60(3), 481–511.
Lumley, J., and Blossey, P. (1998). “Control of turbulence.” Annu. Rev. Fluid Mech., 30(1), 311–327.
Lumley, J. L. (1973). “Drag reduction in turbulent flow by polymer additives.” J. Polym. Sci. Macromol. Rev., 7(1), 263–290.
Motozawa, M., Ishitsuka, S., Iwamoto, K., Ando, H., Senda, T., and Kawaguchi, Y. (2012). “Experimental investigation on turbulent structure of drag reducing channel flow with blowing polymer solution from the wall.” Flow Turbul. Combust., 88(1), 121–141.
Newitt, D. M., Richardson, J. F., Abbott, M., and Turtle, R. B. (1955). “Hydraulic conveying of solids in horizontal pipes.” Chem. Eng. Res. Des., 33a, 93–113.
Ojha, S. P., and Mazumder, B. S. (2008). “Turbulence characteristics of flow region over a series of 2-D dune shaped structures.” Adv. Water Resour., 31(3), 561–576.
Pope, S. B. (2000). Turbulent flows, Cambridge University Press, New York.
Ptasinski, P. K., Nieuwstadt, F. T. M., van den Brule, B. H. A. A., and Hulsen, M. A. (2001). “Experiments in turbulent pipe flow with polymer additives at maximum drag reduction.” Flow Turbul. Combust., 66(2), 159–182.
Rabenjafimanantsoa, A. H., Time, R. W., and Saasen, A. (2007). “Characteristic of the velocity profiles over fixed dunes in pipe.” Annu. Trans. Nordic Rheol. Soc., 15, 141–148.
Robinson, S. K. (1991). “Coherent motions in the turbulent boundary layer.” Annu. Rev. Fluid Mech., 23(1), 601–639.
Schmeeckle, M. W., Shimizu, Y., Baba, H., and Ikezaki, S. (1999). “Numerical and experimental investigation of turbulence over dunes in open-channel flow.” Mon. Rep. Civ. Eng. Res. Inst., 551, 2–15.
Schoppa, W., and Hussain, F. (1998). “A large-scale control strategy for drag reduction in turbulent boundary layers.” Phys. Fluids, 10(5), 1049–1051.
Sirovich, L., and Karlsson, S. (1997). “Turbulent drag reduction by passive mechanisms.” Nature, 388(6644), 753–755.
Stoesser, T., Braun, C., Garcia-Villalba, M., and Rodi, W. (2008). “Turbulence structures in flow over two-dimensional dunes.” J. Hydr. Eng., 42–55.
Su, Z., and Gudmundsson, J. S. (1998). “Perforation inflow reduces frictional pressure loss in horizontal wellbores.” J. Pet. Sci. Eng., 19(3–4), 223–232.
Swamee, P. (1993). “Generalized inner region velocity distribution equation.” J. Hydr. Eng., 651–656.
von Kármán, T. (1930). “Mechanische ähnlichkeit und turbulenz.” Proc., 3rd Int. Congress for Applied Mechanics, Stockholm, Sweden, 85–105.
Wagner, C., Kuhn, S., and Rudolf von Rohr, P. (2007). “Scalar transport from a point source in flows over wavy walls.” Exp. Fluids, 43(2), 261–271.
Wallace, J. M., Eckelmann, H., and Brodkey, R. S. (1972). “The wall region in turbulent shear flow.” J. Fluid Mech., 54(1), 39–48.
Webb, R. L., Eckert, E. R. G., and Goldstein, R. J. (1971). “Heat transfer and friction in tubes with repeated-rib roughness.” Int. J. Heat Mass Transfer, 14(4), 601–617.
White, C. M., Somandepalli, V. S. R., and Mungal, M. G. (2004). “The turbulence structure of drag-reduced boundary layer flow.” Exp. Fluids, 36(1), 62–69.
Willmarth, W. W., and Lu, S. S. (1972). “Structure of the Reynolds stress near the wall.” J. Fluid Mech., 55(01), 65–92.
Woolford, B., Prince, J., Maynes, D., and Webb, B. W. (2009). “Particle image velocimetry characterization of turbulent channel flow with rib patterned superhydrophobic walls.” Phys. Fluids, 21(8), 085106–085112.
Information & Authors
Information
Published In
Copyright
© 2014 American Society of Civil Engineers.
History
Received: Sep 5, 2013
Accepted: Aug 11, 2014
Published online: Oct 6, 2014
Discussion open until: Mar 6, 2015
Published in print: May 1, 2015
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.