Preliminary Design and Engineering of Pipe Ramming Installations
Publication: Journal of Pipeline Systems Engineering and Practice
Volume 3, Issue 4
Abstract
Installation of new buried pipes and culverts, and replacement of existing ones utilizing trenchless technologies, is increasing in popularity because these methods mitigate many of the surface disturbances associated with conventional open-cut placement. Pipe ramming is an efficient technique that allows installation of casings in soils that can present difficulties for other trenchless technologies. Despite increasing usage, little technical guidance is available to owners and engineers who plan installations with pipe ramming. This paper provides an overview of the pipe ramming technique, possible design procedures, and governing mechanics associated with pipe ramming, with the goal of providing a baseline for engineered installations and identifying areas for further research. Methods to estimate soil resistance to ramming, analysis of ground deformations, and ground vibrations are discussed and compared with measurements observed in field installations. Soil resistance predictions based on conventional jacking methods are shown to underpredict measured resistances inferred from dynamic load testing. Empirical Gaussian settlement models commonly employed in tunnel engineering were shown to result in somewhat inaccurate predictions for an observed pipe ramming installation in cohesionless soils. Field measurements of the ground vibrations resulting from ramming are presented and compared with commonly used safe vibration standards developed for residential structures; the frequencies of vibration generally range from 20–100 Hz, are considerably high for small source-to-site distances, and attenuate rapidly with radial distance. In general, the study lays a basis for planning pipe installation projects with the intent of providing technical advancement in pipe ramming.
Get full access to this article
View all available purchase options and get full access to this article.
Acknowledgments
The authors gratefully acknowledge support from the Oregon Department of Transportation (ODOT) and Federal Highway Administration (FHWA) through Research Contract SPR-710. Experimental work was carried with the strong support of members of the Oregon and Southwest Washington Chapter of the National Utility Contractor’s Association, including Armadillo Underground; Gonzales Boring and Tunneling; J.W. Fowler Construction; Moore Excavation; Emery and Sons, Incorporated; Peterson Machinery Company; Wyo-Ben, Incorporated; and RDO Equipment.
References
Ariaratnam, S., Chan, W., and Choi, D. (2006). “Utilization of trenchless construction methods in mainland China to sustain urban infrastructure.” Pract. Period. Struct. Des. Constr., 11(3), 134–141.
ASTM. (2004). “Standard test method for marsh funnel viscosity of clay construction slurries.” D6910, West Conshohocken, PA.
ASTM. (2008). “Standard test method for high-strain dynamic testing of deep foundations.” D4945, West Conshohocken, PA.
ASTM. (2010). “Standard specification for electric-fusion (arc) welded steel pipe.” A139/A139M-04, West Conshohocken, PA.
Attewell, P. B. (1988). “An overview of site investigation and long-term tunnelling-induced settlement in soil.” Eng. Geol. Special Pub., 5(1), 55–61.
ATV. (1990). “Structural calculation of driven pipes.” A 161E, Bonn, Germany, 90.
Auld, F. A. (1982). “Determination of pipe jacking loads.” Proc. Pipe Jacking Assoc., Manchester, UK.
Bennett, R. D. (1998). “Jacking forces and ground deformations associated with microtunneling.” Ph.D. thesis, Univ. of Illinois at Urbana-Champaign, Urbana-Champaign, IL.
Chapman, D. N., and Ichioka, Y. (1999). “Prediction of jacking forces for microtunnelling operations.” Tunn. Undergr. Space Technol., 14(supplement 1): 31–41.
Currey, J., Woodbridge, G., and Nicholson, E. (2009). “On grade, large diameter pipe ramming installations.” Int. No-Dig Show, North American Society for Trenchless Technology and International Society for Trenchless Technology, 1–8.
Goble, G. G., Likins, G., and Rausche, F. (1975). “Bearing capacity of piles from dynamic measurements.” Final Rep., Dept. of Civil Engineering, Case Western Reserve Univ., Cleveland, 77.
Goble, G. G., Rausche, F., and Likins, G. (1980). “The analysis of pile driving—A state-of-the-art.” Proc. Int. Seminar on the Application of Stress-Wave Theory on Piles, Stockholm, Sweden, 131–161.
Hannigan, P. J., Goble, G. G., Likins, G. E., and Rausche, F. (2006). “Design and construction of driven pile foundations.”, National Highway Institute, Federal Highway Administration, U.S. Dept. of Transportation, Washington, DC.
Iscimen, M. (2004). “Shearing behavior of curved interfaces.” M.Sc. thesis, Georgia Institute of Technology, Atlanta.
Jensen, N., Roy, D., and Wanless, T. (2007). “Observations of ground movement during pipe ramming operations under a railway embankment.” Proc., 7th Int. Symp. on Field Measurements in Geomechanics, ASCE, Reston, VA, 1–12.
Kim, D., and Lee, J. (2000). “Propagation and attenuation characteristics of various ground vibrations.” Soil Dyn. Earthq. Eng., 19(2), 115–126.
Kramer, S. L. (1996). Geotechnical earthquake engineering, Prentice Hall, 653.
Leca, E., and New, B. (2007). “ITA/AITES report 2006 on settlements induced by tunneling in soft ground.” Tunn. Undergr. Space Technol., 22(2), 119–149.
Loganathan, N., and Poulos, H. G. (1998). “Analytical prediction for tunneling-induced ground movement in clays.” J. Geotech. Eng., 124(9), 846–856.
Marshall, M. (1998). “Pipe-jacked tunneling: Jacking loads and ground movements.” Ph.D. thesis, Magdalen College, Univ. of Oxford, Trinity, UK.
Massarsch, K. R. (1992). “Static and dynamic soil displacements caused by pile driving.” 4th Int. Conf. on the Application of Stress Wave Theory to Piles, Taylor and Francis, New York, 15–24.
Massarch, K. R., and Fellenius, B. H. (2008). “Ground vibrations induced by impact pile driving.” 6th Int. Conf. on Case Histories in Geotechnical Engineering, Missouri Univ. of Science and Technology, Rolla, MO, 1–38.
Meskele, T., and Stuedlein, A. W. (2011). “Performance of an instrumented pipe ramming installation.” Proc., No-Dig Show, North American Society for Trenchless Technology, Paper C-4-03, 1–11.
Najafi, M. (2008). “Pipe ramming projects.”, Reston, VA, 1–71.
Najafi, M., Gunnick, B., and Davis, G. (2005). “Preparation of construction specifications, contract documents, field testing, educational materials, and course offerings for trenchless construction.” Final Rep., Missouri Dept. of Transportation, Jefferson City, MO.
Norris, P. (1992). “The behavior of jacked concrete pipes during site installation.” Ph.D. thesis, Pembrook College, Univ. of Oxford, Trinity, UK.
O’Reilly, M. P., and New, B. M. (1982). “Settlements above tunnels in the United Kingdom-their magnitude and prediction.” Tunnelling 1982: Symposium Proceedings, Institution of Mining and Metallurgy, London, U.K., 173–181.
Orton, C. (2008). “Large diameter HDD pipe installations and HDD assist techniques.” Proc., Pipelines Congress, ASCE, Reston, VA, 1–8.
Peck, R. B. (1969). “Deep excavations and tunnelling in soft ground.” Proc., 7th Int. Conf. on Soil Mechanics and Foundation Engineering, Mexico City, 225–290.
Pellet-Beaucour, A. L., and Kastner, R. (2002). “Experimental and analytical study of friction forces during microtunneling operations.” Tunn. Undergr. Space Technol., 17(1), 83–97.
Piehl, R. (2005). “Summary of trenchless technology for use with USDA Forest Service culverts.” USDA Forest Service, San Dimas Technology and Development Center, San Dimas, CA, 1–15.
Rausche, F., Goble, G., and Likins, G. (1985). “Dynamic determination of pile capacity.” J. Geotech. Eng., 111(3), 367–383.
Rausche, F., Moses, F., and Goble, G. (1972). “Soil resistance predictions from pile dynamics.” J. Soil Mech. Found. Div., 98(9), 917–937.
Schrank, J. S., Havekost, M. D., and Njoloma, S. M. (2009). “Pipe ramming under three active railroad lines in difficult soil conditions.” Int. No-Dig Show, North American Society for Trenchless Technology and International Society for Trenchless Technology, 1–10.
Simicevic, J., and Sterling, R. (2001). “Guidelines for pipe ramming.” Technical Rep., Trenchless Technology Center of Louisiana Technological Univ., Ruston, LA, 4, 1–21.
Staheli, K. (2006). “Jacking force prediction: An interface friction approach based on pipe surface roughness.” Ph.D. dissertation, Georgia Institute of Technology, Atlanta.
Stein, D. (2005). Trenchless technology for installation of cables and pipelines, Stein and Partner, Arnsberg, Germany.
Terzaghi, K. (1936). “Stress distribution in dry and in saturated sand above a yielding trap-door.” Proc., 1st Int. Conf. on Soil Mechanics and Foundation Engineering, Transportation Research Board, Washington, DC, Vol. 1, 307–311.
Terzaghi, K. (1943). Theoretical soil mechanics, Wiley, New York.
TT Group. (2011). 〈=http://www.tracto-technik.com/downloadDocOverID.cfm?docID=4055〉 (Oct. 19, 2011).
Watkins, R. K., and Anderson, L. R. (2000). Structural mechanics of buried pipes, CRC Press, New York.
Weber, W., and Hurtz, G. (1981). “Ermittlung der rohrreibung und entwicklung eines bohrgerätes.” Tiefbau, Ingenieurbau, Straβenbau, 23(8), 550–555 (in German).
Wiss, J. F. (1981). “Construction vibrations: State-of-the-art.” J. Geotech. Eng. Div., 107(2), 167–181.
Yin, K., Peng, J., Wang, Q., and Wang, R. (2003). “Research on a hydraulic impact hammer system for pipe-ramming.” Pipelines Proc., ASCE, Reston, VA, 1194–1200.
Zubko, N. (2003). “Oregon project launches pipe ramming to the next level.” Trenchless Technology online, Feb.
Information & Authors
Information
Published In
Copyright
© 2012 American Society of Civil Engineers.
History
Received: Nov 2, 2011
Accepted: Mar 30, 2012
Published online: Apr 11, 2012
Published in print: Nov 1, 2012
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.