Effect of PVME on Cement Hydration and Pore Creation in Mortar at Elevated Temperatures
Publication: Journal of Materials in Civil Engineering
Volume 35, Issue 4
Abstract
High strength concrete (HSC) has found significant applications in offshore structures, long-span bridges, and tall buildings due to its outstanding strength and durability. There have been concerns regarding the use of HSC in case of fire, especially due to explosive spalling. Polypropylene (PP) fiber has been demonstrated to reduce spalling in concrete. However, the addition of PP fibers adversely affects the concrete’s workability and can lead to non-homogeneous mixes due to fiber agglomeration during compaction. Addition of water soluble polymers in HSC is an innovative approach to avoid spalling under fire circumstances. The present work investigates the influence of polyvinyl methyl ether (PVME) on the hydration of cement, and its pore creation ability in mortars at elevated temperature. PVME was found to reduce the initial rate of hydration of cement, which was confirmed by thermogravimetry analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), isothermal calorimetry and bound water calculations. The rate of hydration increased with time and became greater than that of control samples after 24 h. PVME showed pore creation ability in mortars at high temperatures, which was similar to that of PP-fiber-modified mortars. PVME enhanced the volume of inter-connected pores, which can provide an escape route for gases and moisture and potentially alleviate spalling. It is expected that the present work will form the basis for further assessment and adoption of PVME as an admixture to HSC mixes to reduce its susceptibility to spalling at elevated temperatures.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The support of this work by Centre for Safety Engineering is acknowledged. The authors are grateful to Mr. Nikhil O and Mr. Harsh Shah for their contribution to the work. The authors gratefully acknowledge Prof. Shashank Bishnoi and Mr. Ashirbad Satapathy from Indian Institute of Technology Delhi for their support.
References
Aïtcin, P.-C. 1998. High performance concrete. Boca Raton, FL: CRC Press.
ASTM. 2012. Standard specification for portland cement. ASTM C150-07. West Conshohocken, PA: ASTM.
ASTM. 2016a. Standard test method for amount of water required for normal consistency of hydraulic cement paste. ASTM C187-16. West Conshohocken, PA: ASTM.
ASTM. 2016b. Standard test method for sieve analysis of fine and coarse aggregates. ASTM C136-16. West Conshohocken, PA: ASTM.
ASTM. 2021. Standard test methods for time of setting of hydraulic cement by Vicat needle. ASTM C191-21. West Conshohocken, PA: ASTM.
BIS (Bureau of Indian Standards). 1970. Specification for coarse and fine aggregates from natural resources for concrete. IS 383:1970. Old Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1988a. Methods of physical tests for hydraulic cement, part 4: Determination of consistency of standard cement paste. IS 4031-4. Old Delhi, India: BIS.
BIS (Bureau of Indian Standards). 1988b. Methods of physical tests for hydraulic cement, part 5: Determination of initial and final setting times. IS 4031-5. Old Delhi, India: BIS.
BIS (Bureau of Indian Standards). 2013. Ordinary portland cement 53 grade - specification. IS 12269:2013. Old Delhi, India: BIS.
Choe, G., G. Kim, J. Nam, H. Kim, E. Hwang, and S. Lee. 2020. “Effect of mass loss of organic fiber on the water vapor pressure and moisture migration of 150 and 200 MPa ultra-high strength concrete exposed to high temperature.” J. Adv. Concr. Technol. 18 (6): 339–351. https://doi.org/10.3151/jact.18.339.
Diederichs, U. 1995. “High temperature properties and spalling behavior of high strength concrete.” In Vol. 10 of Proc., Fourth Weimar Workshop on High Performance Concrete: Material Properties and Design, 219–235. Weimar, Germany: Hochschule fur Architekture and Bauwesen (Hab).
Diederichs, U., and O. Mertzsch. 2008. “Behaviour of ultra high strength concrete at high temperatures.” In Proc., 2nd Int. Symp. on Ultra High Performance Concrete, 347–354. Kassel, Germany: Kassel University Press.
Ding, Y., C. Zhang, M. Cao, Y. Zhang, and C. Azevedo. 2016. “Influence of different fibers on the change of pore pressure of self-consolidating concrete exposed to fire.” Constr. Build. Mater. 113 (Jun): 456–469. https://doi.org/10.1016/j.conbuildmat.2016.03.070.
Dougill, J. 1972. “Modes of failure of concrete panels exposed to high temperatures.” Mag. Concr. Res. 24 (79): 71–76. https://doi.org/10.1680/macr.1972.24.79.71.
Dwaikat, M., and V. Kodur. 2010. “Fire induced spalling in high strength concrete beams.” Fire Technol. 46 (1): 251–274. https://doi.org/10.1007/s10694-009-0088-6.
Fan, J., G. Li, S. Deng, and Z. Wang. 2019. “Mechanical properties and microstructure of polyvinyl alcohol (PVA) modified cement mortar.” Appl. Sci. 9 (11): 2178. https://doi.org/10.3390/app9112178.
Govindarajan, D., and R. Gopalakrishnan. 2011. “Spectroscopic studies on Indian Portland cement hydrated with distilled water and sea water.” Front. Sci. 1 (1): 21–27. https://doi.org/10.5923/j.fs.20110101.04.
Knapen, E., and D. Van Gemert. 2009. “Cement hydration and microstructure formation in the presence of water-soluble polymers.” Cem. Concr. Res. 39 (1): 6–13. https://doi.org/10.1016/j.cemconres.2008.10.003.
Lau, A., and M. Anson. 2006. “Effect of high temperatures on high performance steel fiber reinforced concrete.” Cem. Concr. Res. 36 (9): 1698–1707. https://doi.org/10.1016/j.cemconres.2006.03.024.
Li, Y., Y. Zhang, E.-H. Yang, and K. H. Tan. 2019. “Effects of geometry and fraction of polypropylene fibers on permeability of ultra-high performance concrete after heat exposure.” Cem. Concr. Res. 116 (Feb): 168–178. https://doi.org/10.1016/j.cemconres.2018.11.009.
Liu, J.-C., and K. H. Tan. 2018. “Mechanism of PVA fibers in mitigating explosive spalling of engineered cementitious composite at elevated temperature.” Cem. Concr. Compos. 93 (Oct): 235–245. https://doi.org/10.1016/j.cemconcomp.2018.07.015.
Liu, X., G. Ye, G. De Schutter, Y. Yuan, and L. Taerwe. 2008. “On the mechanism of polypropylene fibers in preventing fire spalling in self-compacting and high-performance cement paste.” Cem. Concr. Res. 38 (4): 487–499. https://doi.org/10.1016/j.cemconres.2007.11.010.
Maheswaran, S., N. R. Iyer, G. Palani, R. A. Pandi, D. D. Dikar, and S. Kalaiselvam. 2015. “Effect of high temperature on the properties of ternary blended cement pastes and mortars.” J. Therm. Anal. Calorim. 122 (2): 775–786. https://doi.org/10.1007/s10973-015-4817-4.
Muller, I. 2006. “Influence of cellulose ethers on the kinetics of early portland cement hydration.” Ph.D. thesis, Schriftenreihe des Instituts für Mineralogie und Geochemie, Karlsruhe University Press.
Ohama, Y. 1995. Handbook of polymer-modified concrete and mortars: Properties and Process Technology. Amsterdam, Netherlands: Elsevier Science.
Ozawa, M., Z. Bo, Y. Uchida, and H. Morimoto. 2014. “Preventive effects of fibers on spalling of UFC at high temperatures.” J. Struct. Fire Eng. 5 (3): 229–238. https://doi.org/10.1260/2040-2317.5.3.229.
Poon, C. S., Z. Shui, and L. Lam. 2004. “Compressive behavior of fiber reinforced high-performance concrete subjected to elevated temperatures.” Cem. Concr. Res. 34 (12): 2215–2222. https://doi.org/10.1016/j.cemconres.2004.02.011.
Puertas, F., A. Fernández-Jiménez, and M. Blanco-Varela. 2004. “Pore solution in alkali-activated slag cement pastes. Relation to the composition and structure of calcium silicate hydrate.” Cem. Concr. Res. 34 (1): 139–148. https://doi.org/10.1016/S0008-8846(03)00254-0.
Saito, H. 1966. “Explosive spalling of prestressed concrete in fire.” Bull. Jpn. Assoc. Fire Sci. Eng. 15 (2): 23–30.
Shen, D., C. Liu, C. Li, X. Zhao, and G. Jiang. 2019. “Influence of Barchip fiber length on early-age behavior and cracking resistance of concrete internally cured with super absorbent polymers.” Constr. Build. Mater. 214 (Jun): 219–231. https://doi.org/10.1016/j.conbuildmat.2019.03.209.
Shorter, G., and T. Harmathy. 1965. “Moisture clog spalling.” Proc. Inst. Civ. Eng. 20 (Oct): 75–90.
Silva, D., H. Roman, and V. John. 2004. “Effects of EVA and HEC polymers on the Portland cement hydration.” In Proc., 11th Int. Congress on Polymers in Concrete, 91–97, Berlin: ACI.
Soshiroda, T., K. Hayakawa, K. Yoda, and M. Tanaka. 1986. “Effects of cellulose ether on homogeneity of concrete in structures—Relating quality variations and construction joints.” In Adhesion between polymers and concrete/Adhésion entre polymères et béton, 125–133. New York: Springer.
Sullivan, P., and A. Zaman. 1971. Explosive spalling of concrete exposed to high temperatures. Berlin: International Association for Structural Mechanics in Reactor Technology.
Taylor, H., C. Famy, and K. Scrivener. 2001. “Delayed ettringite formation.” Cem. Concr. Res. 31 (5): 683–693. https://doi.org/10.1016/S0008-8846(01)00466-5.
Taylor, H. F., et al. 1997. Vol. 2 of Cement chemistry. London: Thomas Telford.
Trezza, M. A. 2007. “Hydration study of ordinary portland cement in the presence of zinc ions.” Mater. Res. 10 (4): 331–334. https://doi.org/10.1590/S1516-14392007000400002.
Tsimbrovska, M., P. Kalifa, D. Quenard, and J. Daian. 1997. High performance concretes at elevated temperature: Permeability and microstructure. Lyon, France: IASMiRT.
Ye, J., J. Xu, J. Hu, X. Wang, G. Zhang, S. Liu, and C. Wu. 2008. “Comparative study of temperature-induced association of cyclic and linear poly (N-isopropylacrylamide) chains in dilute solutions by laser light scattering and stopped-flow temperature jump.” Macromolecules 41 (12): 4416–4422. https://doi.org/10.1021/ma702196g.
Ylmén, R., U. Jäglid, B.-M. Steenari, and I. Panas. 2009. “Early hydration and setting of Portland cement monitored by IR, SEM and Vicat techniques.” Cem. Concr. Res. 39 (5): 433–439. https://doi.org/10.1016/j.cemconres.2009.01.017.
Zeiml, M., D. Leithner, R. Lackner, and H. A. Mang. 2006. “How do polypropylene fibers improve the spalling behavior of in-situ concrete?” Cem. Concr. Res. 36 (5): 929–942. https://doi.org/10.1016/j.cemconres.2005.12.018.
Zhang, W. Z., X. D. Chen, W.-A. Luo, J. Yang, M. Q. Zhang, and F. M. Zhu. 2009. “Study of phase separation of poly (vinyl methyl ether) aqueous solutions with Rayleigh scattering technique.” Macromolecules 42 (5): 1720–1725. https://doi.org/10.1021/ma802671a.
Information & Authors
Information
Published In
Journal of Materials in Civil Engineering
Volume 35 • Issue 4 • April 2023
Copyright
© 2023 American Society of Civil Engineers.
History
Received: Jan 6, 2022
Accepted: Jul 22, 2022
Published online: Jan 27, 2023
Published in print: Apr 1, 2023
Discussion open until: Jun 27, 2023
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.