Experimental Investigations on the State-Dependent Thermal Conductivity of Sand-Rubber Mixtures
Publication: Journal of Materials in Civil Engineering
Volume 34, Issue 3
Abstract
Soil-rubber mixtures are potential construction materials for use in civil engineering applications such as the thermal insulation layer for buried pipelines in the permafrost zone and underground energy storage systems. Currently, however, the thermal conductivity of soil-rubber mixtures in various stress, saturation, and void ratio conditions is not fully understood. In this study, a stress-controlled apparatus based on the thermal needle probe technique was developed. It was employed to study the influence of the aforementioned factors on the thermal conductivity of sand-rubber mixtures. Thirty-four tests were completed with a wide range of net stresses (), initial degrees of saturation (0%–100%), void ratios (0.45–0.95), and rubber contents (0%, 10%, and 20%). Three replicates were used in each condition. The results showed that the thermal conductivity was strongly dependent not only on void ratio, rubber content, and degree of saturation but also on net stress. For instance, the thermal conductivity of a dry sand-rubber mixture increased by 30% when the stress increased from 0 to 600 kPa. This increase in thermal conductivity can mainly be attributed to an increase in interparticle contact area, accounting for about 25% of the 30% increase; the reduction in void ratio played a minor role. A semiempirical equation was proposed to calculate the thermal conductivity of sand-rubber mixtures at different stress levels.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This work was supported by the National Science Foundation of China through the research Grant No. 52022004. The authors also would like to thank the Research Grants Council (RGC) of the Hong Kong Special Administrative Region (HKSAR) for providing financial support through Grant Nos. 16216116 and AoE/E-603/18.
References
ASTM. 2012. Standard test method for density, relative density (specific gravity), and absorption of coarse aggregate. ASTM C127. West Conshohocken, PA: ASTM.
ASTM. 2014a. Standard test methods for maximum index density and unit weight of soils using vibratory table. ASTM D4253. West Conshohocken, PA: ASTM.
ASTM. 2014b. Standard test methods for minimum index density and unit weight of soils and calculation of relative density. ASTM D4254. West Conshohocken, PA: ASTM.
ASTM. 2014c. Standard test method for determination of thermal conductivity of soil and soft rock by thermal needle probe procedure. ASTM D5334-14. West Conshohocken, PA: ASTM.
Benson, C. H., and M. A. Olson. 1996. “Temperatures of insulated landfill liner.” Transp. Res. Rec. 1534 (1): 24–31. https://doi.org/10.1177/0361198196153400105.
Bosscher, P. J., T. B. Edil, and S. Kuraoka. 1997. “Design of highway embankments using tire chips.” J. Geotech. Geoenviron. Eng. 123 (4): 295–304. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:4(295).
Bristow, K. L. 2002. “Thermal conductivity.” In Proc., Methods of soil analysis: Part 4 Physical Methods, edited by J. H. Dane and C. G. Topp, 1209–1226. Madison, WI: Soil Science Society of America.
Buritatun, A., T. Takaikaew, S. Horpibulsuk, A. Udomchai, M. Hoy, N. Vichitcholchai, and A. Arulrajah. 2020. “Mechanical strength improvement of cement-stabilized soil using natural rubber latex for pavement base applications.” J. Mater. Civ. Eng. 32 (12): 04020372. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003471.
Chen, S. X. 2008. “Thermal conductivity of sands.” Heat Mass Transfer 44 (10): 1241–1246. https://doi.org/10.1007/s00231-007-0357-1.
Christ, M., J. B. Park, and S. S. Hong. 2010. “Laboratory observation of the response of a buried pipeline to freezing rubber-sand backfill.” J. Mater. Civ. Eng. 22 (9): 943–950. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000090.
Clauser, C., and E. Huenges. 1995. “Thermal conductivity of rocks and minerals.” In Rock physics and phase relations: A handbook of physical constants, 105–126. Washington, DC: American Geophysics Union.
Côté, J., and J. M. Konrad. 2005. “A generalized thermal conductivity model for soils and construction materials.” Can. Geotech. J. 42 (2): 443–458. https://doi.org/10.1139/t04-106.
Gallage, C., B. Dareeju, M. Dhanasekar, and T. Ishikawa. 2016. “Effects of principal stress axis rotation on unsaturated rail track foundation deterioration.” Procedia Eng. 143 (Jan): 252–259. https://doi.org/10.1016/j.proeng.2016.06.032.
Guendouz, M., F. Debieb, O. Boukendakdji, E. H. Kadri, M. Bentchikou, and H. Soualhi. 2016. “Use of plastic waste in sand concrete.” J. Mater. Environ. 7 (2): 382–389.
Hannawi, K., S. Kamali-Bernard, and W. Prince. 2010. “Physical and mechanical properties of mortars containing PET and PC waste aggregates.” Waste Manage. 30 (11): 2312–2320. https://doi.org/10.1016/j.wasman.2010.03.028.
Hertz, H. R. 1881. “Über die Berührung fester elastischer Körper (On Contact Between Elastic Bodies)” Journal für die reine und angewandte Mathematik. 92 (1881): 156–171.
Hopmans, J. W., and J. H. Dane. 1986. “Thermal conductivity of two porous media as a function of water content, temperature and density.” Soil Sci. 142 (4): 187–195. https://doi.org/10.1097/00010694-198610000-00001.
Johansen, O. 1975. “Thermal conductivity of soils.” Accessed July 2, 1977. https://apps.dtic.mil/sti/pdfs/ADA044002.pdf.
Kashani, A., T. Duc, P. Mendis, and J. R. Black. 2017. “A sustainable application of recycled tyre crumbs as insulator in lightweight cellular concrete.” J. Cleaner Prod. 149 (Apr): 925–935. https://doi.org/10.1016/j.jclepro.2017.02.154.
Ladd, R. S. 1978. “Preparing test specimens using under compaction.” Geotech. Test. J. 1 (1): 16–23. https://doi.org/10.1520/GTJ10364J.
Lee, C., H. Shin, and J. S. Lee. 2014. “Behaviour of sand–rubber particle mixtures: Experimental observations and numerical simulations.” Int. J. Numer. Anal. Methods Geomech. 38 (16): 1651–1663. https://doi.org/10.1002/nag.2264.
Lee, J. H., R. Salgado, A. Bernal, and C. W. Lovell. 1999. “Shredded tires and rubber-sand as lightweight backfill.” J. Geotech. Geoenviron. Eng. 125 (2): 132–141. https://doi.org/10.1061/(ASCE)1090-0241(1999)125:2(132).
Likos, W. J. 2015. “Pore-scale model for thermal conductivity of unsaturated sand.” Geotech. Geol. Eng. 33 (2): 179–192. https://doi.org/10.1007/s10706-014-9744-9.
Lin, X., and T. T. Ng. 1997. “A three-dimensional discrete element model using arrays of spheres.” Géotechnique 47 (2): 319–329. https://doi.org/10.1680/geot.1997.47.2.319.
Liu, L. L., G. J. Cai, and S. Y. Liu. 2018. “Compression properties and micro-mechanisms of rubber sand particle mixtures considering grain breakage.” Constr. Build. Mater. 187 (Oct): 1061–1072. https://doi.org/10.1016/j.conbuildmat.2018.08.051.
Liu, L. L., G. J. Cai, and X. Y. Liu. 2020a. “Investigation of thermal conductivity and prediction model of recycled tire rubber-sand mixtures as lightweight backfill.” Constr. Build. Mater. 248 (Jul): 118657. https://doi.org/10.1016/j.conbuildmat.2020.118657.
Liu, X. Y., G. J. Cai, S. C. Congress, L. L. Liu, and S. Y. Liu. 2020b. “Investigation of thermal conductivity and prediction model of mucky silty clay.” J. Mater. Civ. Eng. 32 (8): 04020221. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003294.
Lopera Perez, J. C., C. Y. Kwok, and K. Senetakis. 2017. “Micromechanical analyses of the effect of rubber size and content on sand-rubber mixtures at the critical state.” Geotext. Geomembranes. 45 (2): 81–97. https://doi.org/10.1016/j.geotexmem.2016.11.005.
Losertova, M., M. Štamborska, J. Lapin, and V. Mares. 2016. “Comparison of deformation behavior of 316L stainless steel and Ti6Al4V alloy applied in traumatology.” Metalurgija 55 (4): 667–670.
Lu, N., and Y. Dong. 2015. “Closed-form equation for thermal conductivity of unsaturated soils at room temperature.” J. Geotech. Geoenviron. Eng. 141 (6): 04015016. https://doi.org/10.1061/(ASCE)GT.1943-5606.0001295.
Madhusudhan, B. R., A. Boominathan, and S. Banerjee. 2019. “Factors affecting strength and stiffness of dry sand-rubber tire shred mixtures.” Geotech. Geol. Eng. 37 (4): 2763–2780. https://doi.org/10.1007/s10706-018-00792-y.
Mu, Q. Y., C. Zhou, and C. W. W. Ng. 2020. “Compression and wetting induced volumetric behavior of loess: Macro-and micro-investigations” Transp. Geotech. 23 (1): 100345. https://doi.org/10.1016/j.trgeo.2020.100345.
Ng, C. W. W., C. Zhou, and C. F. Chiu. 2020. “Constitutive modelling of state-dependent behaviour of unsaturated soils: An overview.” Acta Geotech. 15 (10): 2705–2725. https://doi.org/10.1007/s11440-020-01014-7.
Noorzad, R., and M. Raveshi. 2017. “Mechanical behavior of waste tire crumbs-sand mixtures determined by triaxial tests.” Geotech. Geol. Eng. 35 (4): 1793–1802. https://doi.org/10.1007/s10706-017-0209-9.
Ochsner, T. E., R. Horton, and T. H. Ren. 2001. “A new perspective on soil thermal properties.” Soil Sci. Soc. Am. J. 65 (6): 1641–1647. https://doi.org/10.2136/sssaj2001.1641.
Ocłoń, P., M. Bittelli, P. Cisek, E. Kroener, M. Pilarczyk, D. Taler, R. Rao V, and A. Vallati. 2016. “The performance analysis of a new thermal backfill material for underground power cable system.” Appl. Therm. Eng. 108 (Sep): 233–250. https://doi.org/10.1016/j.applthermaleng.2016.07.102.
Smits, K. M., T. Sakaki, A. Limsuwat, and H. I. Tissa. 2010. “Thermal conductivity of sands under varying moisture and porosity in drainage—Wetting cycles.” Vadose Zone J. 9 (1): 172–180. https://doi.org/10.2136/vzj2009.0095.
Tang, A. M., Y. J. Cui, and T. T. Le. 2008. “A study on the thermal conductivity of compacted bentonites.” Appl. Clay Sci. 41 (3–4): 181–189. https://doi.org/10.1016/j.clay.2007.11.001.
Tarnawski, V. R., and H. L. Wey. 2012. “A series-parallel model for estimating the thermal conductivity of unsaturated soils.” Int. J. Thermophys. 33 (7): 1191–1218. https://doi.org/10.1007/s10765-012-1282-1.
Weidenfeld, G., Y. Weiss, and H. Kalman. 2000. “A theoretical model for effective thermal conductivity (ETC) of particulate beds under compression.” Granular Matter 6 (2): 121–129. https://doi.org/10.1007/s10035-004-0170-1.
Willson, C. S., N. Lu, and W. J. Likos. 2012. “Quantification of grain, pore, and fluid microstructure of unsaturated sand from X-Ray computed tomography images.” Geotech. Test. J. 35 (6): 20120075. https://doi.org/10.1520/GTJ20120075.
Woodside, W., and J. H. Messer. 1961. “Thermal conductivity of porous media. I. Unconsolidated sands.” J. Appl. Phys. 32 (9): 1688–1699. https://doi.org/10.1063/1.1728419.
Xiao, Y., G. L. Ma, B. Nan, and J. S. McCartney. 2020. “Thermal conductivity of granular soil mixtures with contrasting particle shapes.” J. Geotech. Geoenviron. Eng. 146 (5): 06020004. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002243.
Xiao, Y., B. Nan, and J. S. McCartney. 2019. “Thermal conductivity of sand–Tire shred mixtures.” J. Geotech. Geoenviron. Eng. 145 (11): 06019012. https://doi.org/10.1061/(ASCE)GT.1943-5606.0002155.
Yao, J., T. F. Wang, and W. J. Likos. 2019. “Measuring thermal conductivity of unsaturated sand under different temperatures and stress levels using a suction-controlled thermo-mechanical method.” In Geo-Congress 2019 GSP 310, 784–793. Reston, VA: ASCE.
Yun, T. S., and J. C. Santamarina. 2008. “Fundamental study of thermal conduction in dry soils.” Granular Matter 10 (3): 197–207. https://doi.org/10.1007/s10035-007-0051-5.
Zhang, N., X. Yu, A. Pradhan, and A. J. Puppala. 2015. “Thermal conductivity of quartz sands by thermo-time domain reflectometry probe and model prediction.” J. Mater. Civ. Eng. 27 (12): 04015059. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001332.
Zhang, N., X. B. Yu, A. Pradhan, and A. J. Puppala. 2017. “A new generalized soil thermal conductivity model for sand–kaolin clay mixtures using thermo-time domain reflectometry probe test.” Acta Geotech. 12 (4): 739–752. https://doi.org/10.1007/s11440-016-0506-0.
Zhen, Z. L., G. L. Ma, H. Y. Zhang, Y. Gai, and Z. Y. Su. 2019. “Thermal conductivities of remolded and undisturbed loess.” J. Mater. Civ. Eng. 31 (2): 04018379. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002595.
Zhou, C., and R. Chen. 2021. “Modelling the water retention behaviour of anisotropic soils.” J. Hydrol. 599 (Aug): 126361. https://doi.org/10.1016/j.jhydrol.2021.126361.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Mar 25, 2021
Accepted: Aug 3, 2021
Published online: Dec 29, 2021
Published in print: Mar 1, 2022
Discussion open until: May 29, 2022
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Sheqiang Cui, Chao Zhou, Cao Shi, Hu Lu, Thermomechanical Behavior of Energy Piles with Different Roughness Values in Unsaturated Soil, Journal of Geotechnical and Geoenvironmental Engineering, 10.1061/JGGEFK.GTENG-11735, 150, 5, (2024).
- Arjun Sivaprasad, Prasenjit Basu, Effect of Fines on Thermal Conductivity of Dry Sand-Kaolin Mixture, Geo-Congress 2024, 10.1061/9780784485309.052, (509-518), (2024).
- S. Q. Cui, C. Zhou, Coupled effects of stress state and void ratio on thermal conductivity of saturated soils, Géotechnique Letters, 10.1680/jgele.22.00001, 12, 2, (148-153), (2022).
- Byeonguk Ryu, Hyunwook Choo, Junghee Park, Susan E. Burns, Stress–Deformation Response of Rigid–Soft Particulate Mixtures under Repetitive Ko Loading Conditions, Transportation Geotechnics, 10.1016/j.trgeo.2022.100835, 37, (100835), (2022).