Mechanical Property Evaluation of Hybrid Mixed-Species CLT Panels with Sugar Maple and White Spruce
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 7
Abstract
This study evaluated the mechanical properties of hybrid (mixed-species) cross-laminated timber (CLT) panels made of low-value sugar maple (Acer saccharum) and white spruce (Picea glauca). The modulus of elasticity (MOE) of the laminations was measured with a nondestructive method. Three-layer hybrid CLT panels with layup combinations of sugar maple–white spruce–sugar maple and white spruce–sugar maple–white spruce were prepared to evaluate the effects of layups on the performance of the CLT samples. The mechanical properties of hybrid CLT panels were evaluated with different layups and both melamine- and resorcinol-based adhesives. Both long-span and short-span third-point bending tests were conducted to study the flexural and shear behavior of each CLT panel type. It was found that the influence of adhesive types was not significant. The mechanical properties of the hybrid CLT panels with sugar maple surface layers were improved significantly compared with those of the current standard layups. Both bending tests were simulated with finite-element analysis based on measured and reference material properties. The simulated results of each case were in good agreement with the test results.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data, models, and code generated or used during the study appear in the published article.
Acknowledgments
This study was partially supported through a cooperative research agreement (FS 17-JV-11111133-034) between Michigan Technological University and the USDA Forest Service Forest Products Laboratory. The authors are grateful to AJD Forest Products (Grayling, Michigan) for donating the low-value sugar maple lumber for this project.
References
APA (The Engineered Wood Association). 2011. Standard for performance-rated cross laminated timber. ANSI/APA PRG 320. Washington, DC: APA.
APA (The Engineered Wood Association). 2019. Standard for performance-rated cross laminated timber. ANSI/APA PRG-320-2019. Washington, DC: APA.
ASTM. 2011. Standard practice for estimating the percentage of wood failure in adhesive bonded joints. ASTM D5266-99. West Conshohocken, PA: ASTM.
ASTM. 2012. Standard test methods for nondestructive evaluation of wood-based flexural members using transverse vibrations. ASTM D6874-12. West Conshohocken, PA: ASTM.
ASTM. 2013. Standard test method for strength properties of adhesive bonds in shear by compression loading. ASTM D905-08. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test methods of static tests of lumber in structural sizes. ASTM D198. West Conshohocken, PA: ASTM.
Barbero, E. J., F. A. Cosso, R. Roman, and T. L. Weadon. 2013. “Determination of material parameters for Abaqus progressive damage analysis of E-glass epoxy laminates.” Composites, Part B: Eng. 46: 211–220. https://doi.org/10.1016/j.compositesb.2012.09.069.
Beaulieu, J., S. Y. Zhang, Q. Yu, and A. Rainville. 2007. “Comparison between genetic and environmental influences on lumber bending properties in young white spruce.” Wood Fiber Sci. 38 (3): 553–564.
Bendtsen, B. A. 1974. Specific gravity and mechanical properties of black, red, and white spruce and balsam fir. Madison, WI: Dept. of Agriculture, Forest Service, Forest Products Laboratory.
Brandner, R. 2013. Stochastic system actions and effects in engineered timber products and structures. Graz, Austria: Verlag der Technischen Universität Graz.
Brank, B., A. Stanić, M. Lavrenčič, and B. Hudobivnik. 2017. “Design optimization and failure modelling of ribbed cross-laminated timber plates.” In Vol. 4 of Proc., 11th Int. Conf. Shell Structures: Theory and Applications (SSTA 2017), October 11–13, 69. Boca Raton, FL: CRC Press.
Camanho, P. P., and C. G. Dávila. 2002. Mixed-mode decohesion finite elements for the simulation of delamination in composite materials.. Hampton, VI: National Aeronautics and Space Administration.
Chen, Y., and F. Lam. 2012. “Bending performance of box-based cross-laminated timber systems.” J. Struct. Eng. 139 (12): 04013006. https://doi.org/10.1061/%28ASCE%29ST.1943-541X.0000786.
Dickinson, Y., X. Wang, J. Wiedenbeck, and R. J. Ross. 2019. Effects of silviculture practices on engineering properties of northern hardwood species of the Great Lakes Region: A literature review. Madison, WI: US Dept. of Agriculture, Forest Service, Forest Products Laboratory.
Flores, E. I. S., K. Saavedra, J. Hinojosa, Y. Chandra, and R. Das. 2016. “Multi-scale modelling of rolling shear failure in cross-laminated timber structures by homogenisation and cohesive zone models.” Int. J. Solids Struct. 81: 219–232. https://doi.org/10.1016/j.ijsolstr.2015.11.027.
Franke, B., and P. Quenneville. 2014. “Analysis of the fracture behavior of Radiata Pine timber and Laminated Veneer Lumber.” Eng. Fract. Mech. Eng. Fract. Mech. 116: 1–12. https://doi.org/10.1016/j.engfracmech.2013.12.004.
Frühwald, K., and G. Schickhofer. 2005. “Strength grading of hardwoods.” In Proc., 14th Int. Symp. on Nondestructive Testing of Wood, 199–210. Madison, WI: Structural Building Components Association.
Gharib, M., A. Hassanieh, H. Valipour, and M. A. Bradford. 2017. “Three-dimensional constitutive modelling of arbitrarily orientated timber based on continuum damage mechanics.” Finite Elem. Anal. Des. 135: 79–90. https://doi.org/10.1016/j.finel.2017.07.008.
Gong, M., D. Tu, L. Li, and Y. Chui. 2015. “Planar shear properties of hardwood cross layer in hybrid cross laminated timber.” In Proc., ISCHP 2015 85–90. Pointe-Claire, QC: FPInnovations.
Guntekin, E., S. Ozkan, and T. Yilmaz. 2014. “Prediction of bending properties for beech lumber using stress wave method.” Maderas Cienc. Tecnol. 16 (1): 93–98.
Hashin, Z., and A. Rotem. 1973. “A fatigue failure criterion for fiber reinforced materials.” J. Compos. Mater. 7 (4): 448–464. https://doi.org/10.1177/002199837300700404.
He, M., X. Sun, and Z. Li. 2018. “Bending and compressive properties of cross-laminated timber (CLT) panels made from Canadian hemlock.” Constr. Build. Mater. 185: 175–183. https://doi.org/10.1016/j.conbuildmat.2018.07.072.
Hernández, R. E. 2007. “Influence of accessory substances, wood density and interlocked grain on the compressive properties of hardwoods.” Wood Sci. Technol. 41 (3): 249. https://doi.org/10.1007/s00226-006-0114-5.
Hindman, D. P., and J. C. Bouldin. 2015. “Mechanical properties of southern pine cross-laminated timber.” J. Mater. Civ. Eng. 27 (9): 04014251. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001203.
Karacabeyli, E., and B. Douglas. 2013. CLT handbook: Cross-laminated timber. Point-Claire, QC: FPInnovations.
Khasa, P. D., and B. P. Dancik. 1996. “Rapid identification of white-Engelmann spruce species by RAPD markers.” Theor. Appl. Genet. 92 (1): 46–52. https://doi.org/10.1007/BF00222950.
Lu, W., J. Gu, and B. Wang. 2019. “Study on flexural behavior of cross-laminated timber based on different tree species.” Adv. Mater. Sci. Eng. 2019. https://doi.org/10.1155/2019/1728258.
Musah, M. 2020. “Bonding hardwood lumber for cross laminated timber: Properties and environmental impacts.” Ph.D. thesis, College of Forest Resources and Environmental Science, Michigan Technological Univ.
Navaratnam, S., P. B. Christopher, T. Ngo, and T. V. Le. 2020. “Bending and shear performance of Australian Radiata pine cross-laminated timber.” Constr. Build. Mater. 232: 117215. https://doi.org/10.1016/j.conbuildmat.2019.117215.
NHLA (National Hardwood Lumber Association). 2019. Rules for the measurement & inspection of hardwood and cypress. Memphis, TN: NHLA.
Okkonen, E. A., and B. H. River. 1988. “Factors affecting the strength of block-shear specimens.” For. Prod. J. 39 (1): 43–50.
Ross, R. J. 2010. Wood handbook: Wood as an engineering material.. Madison, WI: USDA Forest Service, Forest Products Laboratory.
Sharifnia, H., and D. P. Hindman. 2017. “Effect of manufacturing parameters on mechanical properties of southern yellow pine cross laminated timbers.” Constr. Build. Mater. 156: 314–320. https://doi.org/10.1016/j.conbuildmat.2017.08.122.
Shivnaraine, C. S., and I. Smith. 1990. “Influence of juvenile wood on bending properties of softwood lumber.” J. Forest Eng. 1 (2): 25–33. https://doi.org/10.1080/08435243.1990.10702616.
Sun, X., M. He, and Z. Li. 2020. “Novel engineered wood and bamboo composites for structural applications: State-of-art of manufacturing technology and mechanical performance evaluation.” Constr. Build. Mater. 249: 118751. https://doi.org/10.1016/j.conbuildmat.2020.118751.
Thomas, R. E., and U. Buehlmann. 2017. “Using low-grade hardwoods for CLT production: a yield analysis.” In Proc., 6th Int. Scientific Conf. on Hardwood Processings, edited by V. Möttönen and E. Heinonen, 199–206. Helsinki, Findland: Natural Resources Institute of Finland.
Wang, Z., H. Fu, Y.-H. Chui, and M. Gong. 2014. “Feasibility of using poplar as cross layer to fabricate cross-laminated timber.” In Proc., World Conf. on Timber Engineering. Quebec City: World Conference of Timber Engineering.
Zhou, H., and I. Smith. 2007. “Factors influencing bending properties of white spruce lumber.” Wood Fiber Sci. 23 (4): 483–500.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Jul 19, 2020
Accepted: Nov 18, 2020
Published online: May 5, 2021
Published in print: Jul 1, 2021
Discussion open until: Oct 5, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.
Cited by
- Sumanta Das, Miroslav Gašparík, Anil Kumar Sethy, Tomáš Kytka, Gourav Kamboj, Fatemeh Rezaei, Bonding performance of mixed species cross laminated timber from poplar (Populus nigra L.) and maple (Acer platanoides L.) glued with melamine and PUR adhesive, Journal of Building Engineering, 10.1016/j.jobe.2023.106159, 68, (106159), (2023).
- Munkaila Musah, Javier Hernandez Diaz, Abiodun Oluseun Alawode, Tom Gallagher, Maria Soledad Peresin, Dana Mitchell, Mathew Smidt, Brian Via, Field Assessment of Downed Timber Strength Deterioration Rate and Wood Quality Using Acoustic Technologies, Forests, 10.3390/f13050752, 13, 5, (752), (2022).
- Raviduth Ramful, Assessing the Suitability of Three-Point and Four-Point Bending Simulation to Investigate the Fracture Mechanisms in Directionally-Reinforced Fibre Composites, 2022 IEEE Asia-Pacific Conference on Computer Science and Data Engineering (CSDE), 10.1109/CSDE56538.2022.10089287, (1-4), (2022).
- Suthon Srivaro, Hyungsuk Lim, Minghao Li, Zoltan Pasztory, Properties of mixed species/density cross laminated timber made of rubberwood and coconut wood, Structures, 10.1016/j.istruc.2022.04.016, 40, (237-246), (2022).
- Hao Li, Libin Wang, Yang Wei, Brad Jianhe Wang, Off-axis compressive behavior of cross-laminated bamboo and timber wall elements, Structures, 10.1016/j.istruc.2021.11.009, 35, (452-468), (2022).
- Citra Yanto Ciki Purba, Guillaume Pot, Robert Collet, Myriam Chaplain, Jean-Luc Coureau, Assessment of bonding durability of CLT and glulam made from oak and mixed poplar-oak according to bonding pressure and glue type, Construction and Building Materials, 10.1016/j.conbuildmat.2022.127345, 335, (127345), (2022).
- Xiaofeng Sun, Minjuan He, Zheng Li, Experimental investigation on the influence of lamination aspect ratios on rolling shear strength of cross-laminated timber, Archives of Civil and Mechanical Engineering, 10.1007/s43452-021-00345-w, 22, 1, (2021).