Experimental and Numerical Analysis on Coupled Hygro-Thermo-Chemo-Mechanical Effect in Early-Age Concrete
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 5
Abstract
High-performance concrete easily generates early-age cracks due to its sharp and large temperature and relative humidity (RH) changes. The temperature and RH with and without axial compressive stress were experimentally examined in this study. The test results show that the temperature and RH have an obvious coupled effect at an early age. The RH quickly decreases when the temperature sharply and substantially increases and sharply increases when the temperature steeply and substantially decreases. When the stress is applied, a clear abrupt increase in the RH appears, and when the compressive stress is unloaded, a clear abrupt decrease in the RH appears. During the loading, the decrease rate of RH smaller compared with its development tendency without load. The compressive stress has no significant effect on the temperature. Additionally, based on the previous studies and theoretical derivations, the coupled hygro-thermo-chemo-mechanical model of early-age concrete is proposed. The predicted results calculated by the proposed model are in good agreement with the test data in this study and the open literature.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request. All the experimental data and numerical code can be requested.
Acknowledgments
This project was funded by the National Natural Science Foundation of China under Grant Nos. U1965105, 51878245, U1706222, and 51578268.
References
Al-Rub, R., A. Ashour, and B. Tyson. 2012. “On the aspect ratio effect of multi-walled carbon nanotube reinforcements on the mechanical properties of cementitious nanocomposites.” Constr. Build. Mater. 35 (Oct): 647–655. https://doi.org/10.1016/j.conbuildmat.2012.04.086.
Attiogbe, E. K., S. Schaef, C. O. Kerobo, D. Vojtko, and C. K. Nmai. 2014. “A new fiber for enhanced crack control: Polypropylene fiber with chemical bond to concrete.” Concr. Int. 36 (12): 35–39.
Azenha, M., R. Faria, and D. Ferreira. 2009. “Identification of early-age concrete temperatures and strains: Monitoring and numerical simulation.” Cem. Concr. Compos. 31 (6): 369–378. https://doi.org/10.1016/j.cemconcomp.2009.03.004.
Barluenga, G., and F. Hernández-Olivares. 2007. “Cracking control of concretes modified with short AR-glass fibers at early age: Experimental results on standard concrete and SCC.” Cem. Concr. Res. 37 (12): 1624–1638. https://doi.org/10.1016/j.cemconres.2007.08.019.
Bazant, Z., and L. Najjar. 1972. “Nonlinear water diffusion in nonsaturated concrete.” Mater. Struct. 5 (1): 3–20. https://doi.org/10.1007/BF02479073.
Bažant, Z. P., A. B. Hauggaard, S. Baweja, and F. J. Ulm. 1997. “Microprestress-solidification theory for concrete creep. I: Aging and drying effects.” J. Eng. Mech. 123 (11): 1188–1194. https://doi.org/10.1061/(ASCE)0733-9399(1997)123:11(1188).
Chen, B. M., B. X. Wang, and L. Q. Zhang. 2004. “Numerical study on Soret-effect and Dufour-effect in porous enclosure.” [In Chinese.] J. Eng. Thermophys. 25 (9): 123–126.
Chen, D. 2007. “Study on numerical simulation of hygro-thermal deformation of concrete based on heat and moisture transfer in porous medium and its application.” [In Chinese.] Ph.D. thesis, College of Materials Science and Engineering, Southeast Univ.
Cheng, C. 2010. “Soret and dufour effects on free convection boundary layer over a vertical cylinder in a saturated porous medium.” Int. Commun. Heat Mass. 37 (7): 796–800. https://doi.org/10.1016/j.icheatmasstransfer.2010.05.014.
Du, M. 2015. “Thermo-hygro-mechanical model of early-age concrete based on micro-pore structure evolution.” [In Chinese.] M.S. thesis, Dept. of Civil Engineering, Zhejiang Univ.
Du, M., X. Jin, H. Ye, N. Jin, and Y. Tian. 2016. “A coupled hygro-thermal model of early-age concrete based on micro-pore structure evolution.” Constr. Build. Mater. 111 (May): 689–698. https://doi.org/10.1016/j.conbuildmat.2015.10.187.
Fahmi, H., M. Polivka, and B. Bresler. 1972. “Effects of sustained and cyclic elevated temperature on creep of concrete.” Cem. Concr. Res. 2 (5): 591–606. https://doi.org/10.1016/0008-8846(72)90113-5.
Freiesleben, H., and E. J. Pedersen. 1977. “Maturity computer for controlling curing and hardening of concrete.” Nordiska Betongfoerbundet 1 (19): 21–25.
Gasch, T., R. Malm, and A. Ansell. 2016. “A coupled hygro-thermo-mechanical model for concrete subjected to variable environmental conditions.” Int. J. Solids Struct. 91 (Aug): 143–156. https://doi.org/10.1016/j.ijsolstr.2016.03.004.
Gawin, D., and P. Francesco. 1977. “Thermo-chemo-mechanical model for concrete. I: Hydration and aging.” Int. J. Numer. Methods Eng. 67 (3): 332–363. https://doi.org/10.1002/nme.1636.
Gawin, D., F. Pesavento, and B. A. Schrefler. 2010. “Hygro-thermo-chemo-mechanical modelling of concrete at early ages and beyond. Part I: Hydration and hygro-thermal phenomena.” Int. J. Numer. Methods Eng. 67 (3): 332–363. https://doi.org/10.1002/nme.1636.
Gueribiz, D., F. Jacquemin, and S. Fréour. 2013. “A moisture diffusion coupled model for composite materials.” Eur. J. Mech. A. Solids 42 (6): 81–89. https://doi.org/10.1016/j.euromechsol.2013.04.008.
Hou, D., T. Li, and P. Wang. 2018. “Molecular dynamics study on the structure and dynamics of NaCl solution transport in the nanometer channel of CASH gel.” ACS Sustainable Chem. Eng. 6 (7): 9498–9509. https://doi.org/10.1021/acssuschemeng.8b02126.
Jensen, O., and P. Hansen. 1999. “Influence of temperature on autogenous deformation and relative humidity change in hardening cement paste.” Cem. Concr. Res. 29 (4): 567–575. https://doi.org/10.1016/S0008-8846(99)00021-6.
Jiang, Z., Z. Sun, and P. Wang. 2005. “Autogenous relative humidity change and autogenous shrinkage of high-performance cement pastes.” Cem. Concr. Res. 35 (8): 1539–1545. https://doi.org/10.1016/j.cemconres.2004.06.028.
Kang, S. T., J. S. Kim, Y. Lee, Y. D. Park, and J. K. Kim. 2012. “Moisture diffusivity of early age concrete considering temperature and porosity.” KSCE J. Civ. Eng. 16 (1): 179–188. https://doi.org/10.1007/s12205-012-1445-4.
Khan, M. I. 2002. “Factors affecting the thermal properties of concrete and applicability of its prediction models.” Build. Environ. 37 (6): 607–614. https://doi.org/10.1016/S0360-1323(01)00061-0.
Kim, K. H., S. E. Jeon, J. K. Kim, and S. Yang. 2003. “An experimental study on thermal conductivity of concrete.” Cem. Concr. Res. 33 (3): 363–371. https://doi.org/10.1016/S0008-8846(02)00965-1.
Konsta-Gdoutos, M. S., Z. S. Metaxa, and S. P. Shah. 2010. “Highly dispersed carbon nanotube reinforced cement based materials.” Cem. Concr. Res. 40 (7): 1052–1059. https://doi.org/10.1016/j.cemconres.2010.02.015.
Kumar, S., P. Kolay, S. Malla, and S. Mishra. 2012. “Effect of multiwalled carbon nanotubes on mechanical strength of cement paste.” J. Mater. Civ. Eng. 24 (1): 84–91. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000350.
Kunzel, H. M. 1995. Simultaneous heat and moisture transport in building components: One- and two-dimensional calculation using simple parameters. Stuttgart, Germany: Informationszentrum Raum und Bau Verlag.
Li, H., J. Liu, Y. Wang, T. Yao, Q. Tian, and S. Li. 2015. “Deformation and cracking modeling for early-age sidewall concrete based on the multi-field coupled mechanism.” Constr. Build. Mater. 88 (Jul): 84–93. https://doi.org/10.1016/j.conbuildmat.2015.03.005.
Li, W., Z. Huang, G. Hu, W. H. Duan, and S. P. Shah. 2016. “Early-age shrinkage development of ultra-high-performance concrete under heat curing treatment.” Constr. Build. Mater. 131 (Jan): 767–774. https://doi.org/10.1016/j.conbuildmat.2016.11.024.
Liu, Q. F., G. L. Feng, J. Xia, J. Yang, and L. Y. Li. 2018. “Ionic transport features in concrete composites containing various shaped aggregates: A numerical study.” Compos. Struct. 183 (Jan): 371–380. https://doi.org/10.1016/j.compstruct.2017.03.088.
Luzio, G., and G. Cusatis. 2009. “Hygro-thermo-chemical modeling of high performance concrete. I: Theory.” Cem. Concr. Compos. 31 (5): 301–308. https://doi.org/10.1016/j.cemconcomp.2009.02.015.
Mansour, A., A. Amahmid, M. Hasnaoui, and M. Bourich. 2004. “Soret effect on double-diffusive multiple solutions in a square porous cavity subject to cross gradients of temperature and concentration.” Int. Commun. Heat Mass Transfer 31 (3): 431–440. https://doi.org/10.1016/j.icheatmasstransfer.2004.02.013.
Nagy, B., and D. Szagri. 2016. “Hygrothermal properties of steel fiber reinforced concretes.” In Vol. 824 of Applied mechanics and materials, 579–588. Zürich, Switzerland: Trans Tech.
Nagy, B., and D. Szagri. 2018. “Thermophysical behaviour of reinforced concretes.” In Proc., 6th Int. Conf. Contemporary Achievements in Civil Engineer, 243–253. Novi Sad, Serbia: Univ. of Novi Sad. https://doi.org/10.14415/konferencijaGFS2018.023.
Neumann, S., and G. Marom. 1985. “Stress dependence of the coefficient of moisture diffusion in composite materials.” Polym. Compos. 6 (1): 9–12. https://doi.org/10.1002/pc.750060103.
Ouyang, Z., and B. Wan. 2008. “Modeling of moisture diffusion in FRP strengthened concrete specimens.” J. Compos. Constr. 12 (4): 425–434. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:4(425).
Persson, B. 1997. “Self-desiccation and its importance in concrete technology.” Mater. Struct. 30 (5): 293–305. https://doi.org/10.1007/BF02486354.
Pont, S., S. Durand, and B. A. Schrefler. 2007. “A multiphase thermo-hydro-mechanical model for concrete at high temperatures—Finite element implementation and validation under LOCA load.” Nucl. Eng. Des. 237 (22): 2137–2150. https://doi.org/10.1016/j.nucengdes.2007.03.047.
Powers, T. C. 1965. “Mechanisms of shrinkage and reversible creep of hardened cement paste.” In Proc., Int. Symp. on the Structure of Concrete, 319–344. London: Cement and Concrete Association.
Powers, T. C. 1968. “The thermodynamics of volume change and creep.” Mat. Constr. 1 (6): 487–507. https://doi.org/10.1007/BF02473638.
Ramezani, M., Y. H. Kim, and Z. Sun. 2019a. “Mechanical properties of carbon nanotube reinforced cementitious materials: Database and statistical analysis.” Mag. Concr. Res. 72 (20): 1047–1071. https://doi.org/10.1680/jmacr.19.00093.
Ramezani, M., Y. H. Kim, and Z. Sun. 2019b. “Modeling the mechanical properties of cementitious materials containing CNTs.” Cem. Concr. Compos. 104 (Nov): 103347. https://doi.org/10.1016/j.cemconcomp.2019.103347.
Schutter, G. D. 2002. “Finite element simulation of thermal cracking in massive hardening concrete elements using degree of hydration based material laws.” Comput. Struct. 80 (27–30): 2035–2042. https://doi.org/10.1016/S0045-7949(02)00270-5.
Schutze, M. 1985. “Deformation and cracking behavior of protective oxide scales on heat-resistant steels under tensile strain.” Oxid. Met. 24 (3–4): 199–232. https://doi.org/10.1007/BF0066https://doi.org/10.1007/BF00664232.
Standardization Administration of China. 2018. Common portland cement. [In Chinese.] GB 175-2018. Beijing: Standards Press of China.
Standardization Administration of China. 2019. Standard for test methods of concrete physical and mechanical properties. [In Chinese.] GB/T 50081-2019. Beijing: Standards Press of China.
Tang, S. B., Q. L. Yu, H. Li, C. Y. Yu, C. Y. Bao, and C. A. Tang. 2013. “Mesomechanical model of moisture diffusion and shrinkage cracking in building material—Model development.” Constr. Build. Mater. 47 (Oct): 511–529. https://doi.org/10.1016/j.conbuildmat.2013.05.040.
Ulm, F. J. 1998. “Couplings in early-age concrete: From material modeling to structural design.” Int. J. Solids Struct. 35 (31–32): 4295–4311. https://doi.org/10.1016/S0020-7683(97)00317-X.
Wang, Q., D. Wang, and H. Chen. 2017. “The role of fly ash microsphere in the microstructure and macroscopic properties of high-strength concrete.” Cem. Concr. Compos. 83 (Oct): 125–137. https://doi.org/10.1016/j.cemconcomp.2017.07.021.
Wang, X., H. Cho, and H. Lee. 2011. “Prediction of temperature distribution in concrete incorporating fly ash or slag using a hydration model.” Composites, Part B 42 (1): 27–40. https://doi.org/10.1016/j.compositesb.2010.09.017.
Wu, S., D. Huang, F. B. Lin, H. Zhao, and P. Wang. 2011. “Estimation of cracking risk of concrete at early age based on thermal stress analysis.” J. Therm. Anal. Calorim. 105 (1): 171–186. https://doi.org/10.1007/s10973-011-1512-y.
Wyrzykowski, M., and P. Lura. 2014. “The effect of external load on internal relative humidity in concrete.” Cem. Concr. Res. 65 (Nov): 58–63. https://doi.org/10.1016/j.cemconres.2014.07.011.
Xi, Y., Z. P. Bazant, and H. M. Jennings. 1994. “Moisture diffusion in cementitious materials adsorption isotherms.” Adv. Cem. Based Mater. 1 (6): 248–257. https://doi.org/10.1016/1065-7355(94)90033-7.
Yang, R. 2018. “Research on hydration-thermo-hygro-mechanical coupled model and numerical simulation for early-age concrete.” [In Chinese.] M.S. thesis, College of Civil and Transportation Engineering, Hohai Univ.
Youssef, G., S. Freour, and F. Jacquemin. 2009. “Stress-dependent moisture diffusion in composite materials.” J. Compos. Mater. 43 (15): 1621–1637. https://doi.org/10.1177/0021998309339222.
Zhang, J., Y. Gao, Y. Han, and W. Sun. 2012a. “Shrinkage and interior humidity of concrete under dry–wet cycles.” Drying Technol. 30 (6): 583–596. https://doi.org/10.1080/07373937.2011.653614.
Zhang, J., D. Hou, and Y. Han. 2012b. “Micromechanical modeling on autogenous and drying shrinkages of concrete.” Constr. Build. Mater. 29 (Apr): 230–240. https://doi.org/10.1016/j.conbuildmat.2011.09.022.
Zhang, J., K. Qi, and Y. Huang. 2009. “Calculation of moisture distribution in early-age concrete.” J. Eng. Mech. 135 (8): 871–880. https://doi.org/10.1061/(ASCE)0733-9399(2009)135:8(871).
Zhang, P., D. Li, Y. Qiao, S. Zhang, C. Sun, and T. Zhao. 2018. “Effect of air entrainment on the mechanical properties, chloride migration, and microstructure of ordinary concrete and fly ash concrete.” J. Mater. Civ. Eng. 30 (10): 04018265. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002456.
Zhao, H., K. Jiang, R. Yang, Y. Tang, and J. Liu. 2020. “Experimental and theoretical analysis on coupled effect of hydration, temperature and humidity in early-age cement-based materials.” Int. J. Heat Mass Transfer 146 (Jan): 118784. https://doi.org/10.1016/j.ijheatmasstransfer.2019.118784.
Zhao, H., J. Liu, X. Yin, Y. Wang, and D. Huang. 2019a. “A multiscale prediction model and simulation for autogenous shrinkage deformation of early-age cementitious materials.” Constr. Build. Mater. 226 (Aug): 483–491. https://doi.org/10.1016/j.conbuildmat.2019.07.282.
Zhao, H., X. Wu, Y. Huang, P. Zhang, Q. Tian, and J. Liu. 2019b. “Investigation of moisture transport in cement-based materials using low-field nuclear magnetic resonance imaging.” Mag. Concr. Res. 1–19. https://doi.org/10.1680/jmacr.19.00211.
Zhou, C., F. Ren, Z. Wang, W. Chen, and W. Wang. 2017a. “Why permeability to water is anomalously lower than that to many other fluids for cement-based material.” Cem. Concr. Res. 100 (Oct): 373–384. https://doi.org/10.1016/j.cemconres.2017.08.002.
Zhou, W., T. Qi, X. Liu, C. Feng, and S. Yang. 2017b. “A hygro-thermo-chemical analysis of concrete at an early age and beyond under dry-wet conditions based on a fixed model.” Int. J. Heat Mass Transfer 115 (Part B): 488–499. https://doi.org/10.1016/j.ijheatmasstransfer.2017.08.014.
Zunino, F., J. Castro, and M. Lopez. 2015. “Thermo-mechanical assessment of concrete microcracking damage due to early-age temperature rise.” Constr. Build. Mater. 81 (Apr): 140–153. https://doi.org/10.1016/j.conbuildmat.2014.12.126.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Aug 8, 2019
Accepted: Sep 14, 2020
Published online: Feb 24, 2021
Published in print: May 1, 2021
Discussion open until: Jul 24, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.