Influence of Aggregate Gradation on the Compactability of Asphalt Mixtures Utilizing Locking Point
Publication: Journal of Materials in Civil Engineering
Volume 33, Issue 3
Abstract
Aggregate gradation is crucial for the performance of asphalt mixtures. However, the adequate mix design must include the compromise between performance and workability. This study used two compaction methods: the impact (Marshall Hammer, Humboldt, Elgin, Illinois) and gyratory [Superpave Gyratory Compactor (SGC), Pine Instrument Company, Grove City, Pennsylania], to investigate the influence of aggregate gradation on the compaction of asphalt mixture utilizing the concept of the locking point. For the impact compaction, an accelerometer was placed on the falling mass of the Marshall Hammer to record the asphalt mix response, with which the impact locking point was defined. For the gyratory compaction, the densification curves were utilized to define the locking point. Twelve mixes, three for each mixture type (base, intermediate, and surface) were designed and prepared in the laboratory. The asphalt mixes were tested for their locking points in relation to their type and gradation. Results indicated that the locking point could be determined for the majority of the mixtures compacted by both the impact and gyration methods, except for the mixture composed of the bigger stone and coarser gradation. The locking point of the asphalt mixture was strongly dependent on its gradation. A coarser mix resulted in a higher locking point. Thus, the maximum aggregate size was not the only factor that determined the locking point but the whole gradation.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request.
Acknowledgments
The project was sponsored by the Tennessee DOT (United States). The authors would like to thank Tennessee DOT engineers and contractors who helped provide the aggregates and asphalt binder for this study.
References
ASTM. 2011. Standard test method for theoretical maximum specific gravity and density of bituminous paving mixtures. ASTM D2041. West Conshohocken, PA: ASTM.
ASTM. 2015a. Standard test method for relative density (specific gravity) and absorption of coarse aggregate. ASTM C127. West Conshohocken, PA: ASTM.
ASTM. 2015b. Standard test method for relative density (specific gravity) and absorption of fine aggregate. ASTM C128. West Conshohocken, PA: ASTM.
ASTM. 2017. Standard test method for bulk specific gravity and density of non-absorptive compacted asphalt mixtures. ASTM D2726. West Conshohocken, PA: ASTM.
Brown, E. R., J. L. McRae, and A. B. Crawley. 1989. “Effect of aggregates on performance of bituminous concrete.” In Implication of aggregates in the design, construction, and performance of flexible pavements, 34–63. West Conshohocken, PA: ASTM.
Garcia, V., L. Barros, J. Garibay, I. Abdallah, and S. Nazarian. 2020. “Effect of aggregate gradation on performance of asphalt concrete mixtures.” J. Mater. Civ. Eng. 32 (5): 04020102. https://doi.org/10.1061/(ASCE)MT.1943-5533.0003147.
Gong, H., Y. Sun, W. Hu, P. A. Polaczyk, and B. Huang. 2019. “Investigating impacts of asphalt mixture properties on pavement performance using LTPP data through random forests.” Constr. Build. Mater. 204 (Apr): 203–212. https://doi.org/10.1016/j.conbuildmat.2019.01.198.
Hall, K., S. Dandu, and G. Gowda. 1996. “Effect of specimen size on compaction and volumetric properties in gyratory compacted hot-mix asphalt concrete specimens.” Transp. Res. Rec. 1545 (1): 126–132. https://doi.org/10.1177/0361198196154500117.
Jia, X., W. Hu, P. Polaczyk, H. Gong, and B. Huang. 2019. “Comparative evaluation of compacting process for base materials using lab compaction methods.” Transp. Res. Rec. 2673 (4): 558–567. https://doi.org/10.1177/0361198119837953.
Jiang, J., F. Ni, X. Gu, L. Yao, and Q. Dong. 2019. “Evaluation of aggregate packing based on thickness distribution of asphalt binder, mastic and mortar within asphalt mixtures using multiscale methods.” Constr. Build. Mater. 222 (Oct): 717–730. https://doi.org/10.1016/j.conbuildmat.2019.06.083.
Leiva, F., and R. West. 2008. “Analysis of hot-mix asphalt lab compactability using lab compaction parameters and mix characteristics.” Transp. Res. Rec. 2057 (1): 89–98. https://doi.org/10.3141/2057-11.
Ma, Y., W. Hu, P. Polaczyk, B. Han, R. Xiao, M. Zhang, and B. Huang. 2020. “Rheological and aging characteristics of the recycled asphalt binders with different rejuvenator incorporation methods.” J. Cleaner Prod. 262 (Mar): 121249. https://doi.org/10.1016/j.jclepro.2020.121249.
McGennis, R., R. Anderson, D. Perdomo, and P. Turner. 1996. “Issues pertaining to use of superpave gyratory compactor.” Transp. Res. Rec. 1543 (1): 139–144. https://doi.org/10.1177/0361198196154300118.
Mohammad, L., and K. Shamsi. 2007. “A look at the bailey method and locking point concept in superpave mixture design.” In Transportation research circular E-C124: Practical approaches to hot-mix asphalt mix design and production quality control testing, 12–32. Washington, DC: Transportation Research Board.
Polaczyk, P., B. Han, B. Huang, X. Jia, and X. Shu. 2018. “Evaluation of the hot mix asphalt compactability utilizing the impact compaction method.” Constr. Build. Mater. 187 (Oct): 131–137. https://doi.org/10.1016/j.conbuildmat.2018.07.117.
Polaczyk, P., B. Huang, X. Shu, and H. Gong. 2019a. “Investigation into locking point of asphalt mixtures utilizing superpave and marshall compactors.” J. Mater. Civ. Eng. 31 (9): 04019188. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002839.
Polaczyk, P., X. Shu, H. Gong, and B. Huang. 2019b. “Influence of aggregates angularity on the locking point of asphalt mixtures.” Road Mater. Pavement Des. 20 (1): 183–195. https://doi.org/10.1080/14680629.2019.1588151.
Prowell, B., and E. Brown. 2007. Superpave mix design: Verifying gyration levels in the N design table. Washington, DC: National Cooperative Highway Research Program.
Roberts, F., P. Kandhal, E. Brown, D. Lee, and T. Kennedy. 1991. Hot mix asphalt materials, mixture design, and construction. Lanham, MD: National Asphalt Pavement Association Research.
Shamsi, K., and L. Mohammad. 2010. “Estimating optimum compaction level for dense-graded hot-mix asphalt mixtures.” J. Eng. Res. 7 (1): 11–21. https://doi.org/10.24200/tjer.vol7iss1pp11-21.
Tennessee DOT. 2015. Standard specifications for road and bridge construction. Nashville, TN: Tennessee DOT.
Vavrik, W. 2000. “Asphalt mixture design concepts to develop aggregate interlock.” Ph.D. thesis, Dept. of Civil and Environmental Engineering, Univ. of Illinois at Urbana-Champaign.
Vavrik, W., and S. Carpenter. 1998. “Calculating air voids at specified number of gyrations in superpave gyratory compactor.” Transp. Res. Rec. 1630 (1): 117–125. https://doi.org/10.3141/1630-14.
Xiao, F., S. N. Amirkhanian, B. J. Putman, and H. Juang. 2012. “Feasibility of Superpave gyratory compaction of rubberized asphalt concrete mixtures containing reclaimed asphalt pavement.” Constr. Build. Mater. 27 (1): 432–438. https://doi.org/10.1016/j.conbuildmat.2011.07.024.
Information & Authors
Information
Published In
Copyright
© 2021 American Society of Civil Engineers.
History
Received: Mar 31, 2020
Accepted: Aug 6, 2020
Published online: Jan 5, 2021
Published in print: Mar 1, 2021
Discussion open until: Jun 5, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.