Impact of Wastewater Treatment Sludge on Cracking Resistance of Hot Mix Asphalt Mixes at Lower Mixing Temperature
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 12
Abstract
Wastewater treatment sludge (WTS) is a by-product of wastewater treatment. Moisture holding capacity, high organic, complex inorganics, and zeolite-like chemical contents make WTS a valuable pavement additive. This study evaluated the impacts of 1.5% WTS on fatigue cracking and low-temperature cracking resistance of asphalt mixes. Reclaimed asphalt pavement (RAP) from North Dakota Highway-17 and I-29 projects were used. Three mixes—0%, 40%, and 60% RAP content—with and without WTS, were considered. The rheology of extracted RAP was tested for high-temperature continuous temperature, intermediate-temperature fatigue cracking resistance using linear amplitude sweep (LAS), and low-temperature cracking resistance using 4-mm parallel plate geometry. Rheology tests were conducted using a dynamic shear rheometer (DSR). Results showed that RAP from Highway-17 was relatively stiffer than the I-29 RAP. RAP mixes modified with 1.5% WTS were prepared at 40°C (104°F) lower mixing temperature than the control. Semicircular bend (SCB) and disk-shaped compact tension (DCT) tests were used to evaluate the fatigue cracking and low-temperature cracking resistance of the mixes, respectively. Results indicated that WTS improved the fatigue and low-temperature cracking resistance of 0%, 40%, and 60% RAP mixes from both RAP sources. The effect of WTS on fatigue cracking resistance increased with RAP content, whereas the effect of WTS on low-temperature cracking decreased with RAP content. Low-temperature cracking resistance of the 40% RAP mix was 24% higher than that of unmodified 0% RAP mix for Highway-17 mixes, and was almost similar for I-29 mixes. This shows WTS can be used as an additive to improve fatigue and low-temperature cracking resistance of mixes with RAP.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code generated or used during the study are available from the corresponding author by request, including binder rheology, and fatigue and low-temperature cracking resistance of mixes.
Acknowledgments
The authors thank the North Dakota Department of Transportation and the Grand Forks wastewater treatment plant for providing the materials.
References
AASHTO. 2016a. Standard method of test for determining the fracture potential of asphalt mixtures using the flexibility index test (FIT). Washington, DC: AASHTO.
AASHTO. 2016b. Standard specification for performance-graded asphalt binder. Washington, DC: AASHTO.
AASHTO. 2019. Standard method of test for determining the fracture energy of asphalt mixtures using the semicircular bend geometry (SCB). Washington, DC: AASHTO.
ASTM. 2011. Standard test methods for quantitative extraction of bitumen from bituminous paving mixtures. ASTM D2172/D2172M-11. West Conshohocken, PA: ASTM.
ASTM. 2013. Standard test method for determining fracture energy of asphalt-aggregate mixtures using the disk-shaped compact tension geometry. ASTM D7313-13. West Conshohocken, PA: ASTM.
ASTM. 2015. Standard test method for recovery of asphalt from solution by Abson method. ASTM D1856-09. West Conshohocken, PA: ASTM.
Edwards, Y., Y. Tasdemir, and U. Isacsson. 2006. “Effects of commercial waxes on asphalt concrete mixtures performance at low and medium temperatures.” Cold Reg. Sci. Technol. 45 (1): 31–41. https://doi.org/10.1016/j.coldregions.2006.01.002.
Ferreira, C., A. Ribeiro, and L. Ottosen. 2003. “Possible applications for municipal solid waste fly ash.” J. Hazard. Mater. 96 (2–3): 201–216. https://doi.org/10.1016/j.conbuildmat.2017.05.195.
FHWA (Federal Highway Administration). 2016. “User guidelines for waste and byproduct materials in pavement construction.” Accessed May 1, 2020. https://www.fhwa.dot.gov/publications/research/infrastructure/structures/97148/ss2.cfm.
FHWA (Federal Highway Administration). 2018. “Warm mix asphalt technologies and research.” Accessed May 23, 2019. https://www.fhwa.dot.gov/pavement/asphalt/wma.cfm.
Fytili, D., and A. Zabaniotou. 2008. “Utilization of sewage sludge in EU application of old and new methods—A review.” Renewable Sustainable Energy Rev. 12 (1): 116–140. https://doi.org/10.1016/j.rser.2006.05.014.
Gedafa, D., A. Berg, B. Karki, R. Saha, and R. Melaku. 2018. “Cracking and rutting performance of field and laboratory HMA mixes.” In Airfield highway pavements testing and characterization of pavement materials, 12–19. Reston, VA: ASCE.
Gedafa, D., B. Karki, A. Berg, R. Saha, and R. Melaku. 2019. “Effect of nanomaterials on cracking and rutting resistance of HMA.” In Airfield and highway pavements 2019: Innovation and sustainability in highway and airfield pavement technology, 88–95. Reston, VA: ASCE.
Goh, S. W., and Z. You. 2011. “Mechanical properties of porous asphalt pavement materials with warm mix asphalt and RAP.” J. Transp. Eng. 138 (1): 90–97. https://doi.org/10.1061/(ASCE)TE.1943-5436.0000307.
Gordon, C., and Y. Tsung. 1998. “Synthesis of zeolites from municipal incinerator fly ash.” J. Hazard. Mater. 62 (1): 75–89. https://doi.org/10.1016/S0304-3894(98)00163-0.
Hintz, C., R. Velasquez, C. Johnson, and H. Bahia. 2011. “Modification and validation of the linear amplitude sweep test for binder fatigue specification.” Transp. Res. Board Ann. Meeting 2207 (1): 99–106. https://doi.org/10.3141/2207-13.
Hussain, B., P. Teymourpour, D. Swiertz, C. Ling, R. Varma, and T. Mandal. 2016. Analysis and feasibility of asphalt pavement performance-based specifications for WisDOT. Madison, WI: Univ. of Wisconsin.
Kent, H., and A. Copeland. 2017. Asphalt pavement industry survey on recycled materials and warm-mix. Lanham, MD: National Asphalt Pavement Association.
Lin, Y., S. Zhou, F. Li, and Y. Lin. 2012. “Utilization of municipal sewage sludge as additives for the production of eco-cement.” J. Hazard. Mater. 213 (Apr): 457–465. https://doi.org/10.1016/j.jhazmat.2012.02.020.
Liu, J., and L. Peng. 2012. “Low temperature performance of Sasobit-modified warm-mix asphalt.” J. Mater. Civ. Eng. 24 (1): 57–63. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000347.
Medeiros, M. S., J. S. Daniel, H. L. Bolton, and W. C. Meagher. 2011. “Evaluation of moisture and low-temperature cracking susceptibility of warm-mixture asphalt.” Int. J. Pavement Eng. 13 (5): 1–6. https://doi.org/10.1080/10298436.2011.582113.
Melaku, R. S., D. S. Gedafa, and J. Liu. 2020. “Effect of wastewater treatment sludge (WWS) on binder and HMA performance.” In Proc., Transportation Research Board Annual Meeting. Washington, DC: Transportation Research Board.
Mogawer, W., A. Austerman, R. Kluttz, and M. Roussel. 2012. “High-performance thin-lift overlays with high reclaimed asphalt pavement content and warm-mix asphalt technology: Performance and workability characteristics.” Transp. Res. Rec. 2293 (1): 18–28. https://doi.org/10.3141/2293-03.
NEBRA (North East Biosolids Residuals Association). 2007. A national biosolids regulation, quality, end use & disposal survey. Tamworth, NH: NEBRA.
Newcomb, D., E. Brown, and J. Epps. 2007. Designing HMA mixtures with high RAP content: A practical guide. Lanham, MD: National Asphalt Pavement Association.
Orhon, D., and N. Artan. 1995. Modelling of activated-sludge systems, 219–220. Lancaster, PA: Technomic.
Ozer, H., L. Al-Qaid, and J. Lambros. 2016. “Development of the fracture-based flexibility index for asphalt concrete cracking potential using modified semi-circle bending test parameters.” Constr. Build. Mater. 115 (Jul): 390–401. https://doi.org/10.1016/j.conbuildmat.2016.03.144.
Pazos, M., G. M. Kirkelund, and L. M. Ottosten. 2010. “Electrodialytic treatment for metal removal from sewage sludge ash from fluidized bed combustion.” J. Hazard. Mater. 176 (1–3): 1073–1078. https://doi.org/10.1016/j.jhazmat.2009.11.150.
Prashant, S., S. Khyati, A. Alan, T. Chris, N. Aaron, N. Yusuf, and J. Kauser. 2011. “Evaluation of fatigue and rutting performance of sewage sludge ash (SSA) in asphalt concrete.” J. Solid Waste Technol. Manage. 37 (1): 55–60. https://doi.org/10.5276/JSWTM.2011.55.
Rubio, C., G. Martínez, L. Baena, and F. Moreno. 2011. “Warm mix asphalt: an overview.” J. Cleaner Prod. 24: (Mar) 76–84. https://doi.org/10.1016/j.jclepro.2011.11.053.
Sol, M., F. Moreno, M. Rubio, V. Pérez, and P. Cabanillas. 2019. “Reuse of zeolite by-products derived from petroleum refining for sustainable roads.” Adv. Mater. Sci. Eng. 2019 (May): 1–10. https://doi.org/10.1155/2019/4256989.
Sui, C., J. Farrar, M. Harnsberger, H. Tuminello, and F. Turner. 2011. “A new low-temperature performance grading method using 4mm parallel-plates on a DSR.” In Proc., 91st Annual Meeting Compendium Transport Research Board, 43–48. Washington, DC: Transportation Research Board.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Jan 7, 2020
Accepted: Jun 19, 2020
Published online: Sep 29, 2020
Published in print: Dec 1, 2020
Discussion open until: Feb 28, 2021
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.