Abstract
The point-load test method (PLTM) commonly used in the geotechnical area is shown in this paper to estimate the compressive strength of in situ masonry mortar. A specially developed portable PLTM instrument was used for mortar sheet testing. The mortar sheets were removed from horizontal masonry joints by drilling cores out, with little preparatory work required. The test mortar sheets were subjected to pressure from two opposing cone heads, and the peak load at the failure of the mortar sheet was recorded. The effect of specimen size and mortar thickness on the point-load strength was examined. A suitable size of mortar sheet was selected for the experiment. The thickness correction method was used to improve the accuracy of the empirical formula. Scattering characteristics were investigated to check the reliability and repeatability of the PLTM results. A strong relationship was noted between the point-load strength of the mortar sheet and cube compressive strength, ranging from M2.5 to M15.0. Contrast tests with other available test methods verified that the PLTM offers an alternative to the masonry mortar compressive test and has high accuracy, requires little preparation, and involves reproducible and quick operation following specimen extraction from joints.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statements
All data, models, and codes generated or used during the study appear in the published article.
Acknowledgments
The authors would like to acknowledge the National Natural Science Foundation of China (Grant No. 51908341), the Research Project of Changzhou Institute of Technology (Grant Nos. E3-6701-18-064 and YN18044), which collectively funded this project.
References
ASTM. 2012a. Specification for building brick (solid masonry units made from clay or shale). ASTM C62. West Conshohocken, PA: ASTM.
ASTM. 2012b. Specification for hollow brick (hollow masonry units made from clay or shale). ASTM C652. West Conshohocken, PA: ASTM.
ASTM. 2012c. Specification for Portland cement. ASTM C150. West Conshohocken, PA: ASTM.
ASTM. 2012d. Standard specification for standard sand. ASTM C778. West Conshohocken, PA: ASTM.
ASTM. 2012e. Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM C109/C109M-08. West Conshohocken, PA: ASTM.
ASTM. 2012f. Standard test methods for in situ measurement of masonry mortar joint shear strength index. ASTM C1531-16. West Conshohocken, PA: ASTM.
ASTM. 2012g. Standard test method for situ measurement of masonry deformability properties using the Flatjack method. ASTM C1197-14a. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard specification for mortar for unit masonry. ASTM C270-14a. West Conshohocken, PA: ASTM.
ASTM. 2018. Standard test method for water retention of hydraulic cement-based mortars and plasters. ASTM C1506-17. West Conshohocken, PA: ASTM.
Bažant, Z. P. 1991. “Rate effect, size effect and nonlocal concepts for fracture of concrete and other quasi-brittle materials.” In Toughening mechanisms in quasi-brittle materials, 131–153. Dordrecht, Netherlands: Springer.
Broch, E., and J. A. Franklin. 1972. “The point-load strength test.” Int. J. Rock Mech. Min. Sci. Geomech. Abstr. 9 (6): 669–676. https://doi.org/10.1016/0148-9062(72)90030-7.
Carpinteri, A., L. Dimastrogiovanni, and N. Pugno. 2004. “RILEM recommendation MDT. D.1—Indirect determination of the surface strength of unweathered hydraulic cement mortar by the drill energy method.” Mater. Struct. 37 (7): 485–487. https://doi.org/10.1007/BF02481586.
Chen, D. C., T.-Z Chen, and C. X. Shi. 2012. “Research on the evaluation of strength for fired common brick in existing masonry structures in rebound method.” J. Hunan Univ. 39 (3): 23–27. https://doi.org/10.3969/j.issn.1674-2974.2012.03.005.
Chen, X. D., S. X. Wu, and J. K. Zhou. 2013. “Influence of porosity on compressive and tensile strength of cement mortar.” Constr. Build. Mater. 40 (Mar): 869–874. https://doi.org/10.1016/j.conbuildmat.2012.11.072.
Chinese Standards. 2001. Technical specification for testing compressive strength of masonry mortar by penetration resistance method. [In Chinese.] JGJ/T 136. Beijing: National Standard of the People’s Republic of China.
Drdacky, M. 2005. “Identification of historic materials using tests on small samples.” In Proc., 2nd Int. Conf. on Hazards and Modern Heritage, 29–37. Florence, Italy: Univ. of Florence.
Felicetti, R., and N. Gattesco. 1998. “A penetration test to study the mechanical response of mortar in ancient masonry buildings.” Mater. Struct. 31 (5): 350–356. https://doi.org/10.1007/BF02480678.
ISRM (International Society for Rock Mechanics) Committee on Laboratory Tests. 1973. Suggested method for determining the point-load strength index, Document No. 1, 8–12. Salzburg, Austria: ISRM.
Klugt, L. J. 1991. “The pointing hardness tester—An instrument to meet a need.” Mater. Struct. 24 (6): 471–476. https://doi.org/10.1007/BF02472020.
Levent, S. L., and H. S. Gökçe. 2015. “Estimation of the compressive strength of concrete under point load and its approach to strength criterions.” KSCE J. Civ. Eng. 19 (6): 1767–1774. https://doi.org/10.1007/s12205-015-1303-2.
Marastonia, D., A. Benedetti, L. PelàLuca, and G. Pignagnoli. 2017. “Torque penetrometric test for the in-situ characterisation of historical mortars: Fracture mechanics interpretation and experimental validation.” Constr. Build. Mater. 157 (Dec): 509–520. https://doi.org/10.1016/j.conbuildmat.2017.09.120.
Pelà, L., P. Roca, and A. Aprile. 2018. “Combined in-situ and laboratory minor destructive testing of historical mortars.” Int. J. Archit. Heritage 12 (3): 334–349. https://doi.org/10.1080/15583058.2017.1323247.
Rajabi, A. M., and F. O. Moaf. 2017. “Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete.” Constr. Build. Mater. 146 (Aug): 485–492. https://doi.org/10.1016/j.conbuildmat.2017.04.089.
Richardson, D. N. 1989. “Point load test for estimation of concrete compressive strength.” ACI Mater. J. 86 (4): 409–416.
Robins, P., S. Austin, J. Chandler, and P. Jones. 2001. “Flexural strain and crack width measurement of steel-fibre-reinforced concrete by optical grid and electrical gauge methods.” Cem. Concr. Res. 31 (5): 719–729. https://doi.org/10.1016/S0008-8846(01)00465-3.
Rusnak, J., and C. Mark. 1999. “Using the point load test to determine the uniaxial compressive strength of coal measure rock.” In Proc. 19th Int. Conf. on Ground Control in Mining 1999 in Morgantown, 362–371. Morgantown, WV: West Virginia Univ.
Schlaich, J., K. Shafer, and M. Jennewein. 1987. “Toward a consistent design of structural concrete.” PCI J. 32 (3): 74–150. https://doi.org/10.15554/pcij.05011987.74.150.
Tuncel, E. Y., I. P. Pekmezci, and B. Y. Pekmezci. 2016. “Utilization of partially destructive test methods on mechanical properties of historical lime mortars.” In SAHC 2016- Proc., of Structural Analysis of Historical Constructions, 1415–1418. London: Taylor and Francis.
Yang, S. H., R. N. Gu, and S. Y. Cao. 2016. “New local compression test to estimate in situ compressive strength of masonry mortar.” J. Test. Eval. 44 (1): 67–76. https://doi.org/10.1520/JTE20130088.
Information & Authors
Information
Published In
Copyright
© 2020 American Society of Civil Engineers.
History
Received: Sep 27, 2019
Accepted: Mar 2, 2020
Published online: Jul 27, 2020
Published in print: Oct 1, 2020
Discussion open until: Dec 27, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.