Effect of Temperature on Mechanical Properties of Steel Bolts
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 9
Abstract
The strength characteristics of bolts under ambient and fire conditions are among the major factors affecting the performance of bolted connections in steel structures. At present, the evaluation of fire resistance of steel bolts is done under the assumption that the mechanical properties of steel bolts are identical in both the heating and cooling phases of fire. The reason is the scarcity of data regarding the high-temperature properties of steel bolts in the cooling phase of fire. This paper is an attempt to experimentally study the high-temperature mechanical properties of Grade 10.9 high-strength steel bolts both in the heating and cooling phases of fire. The researchers carried out steady-state tension tests on bolt specimens in a temperature range of 20°C–800°C. The test results were used to assess the stress-strain response and the ultimate and yield strength as functions of temperature for Grade 10.9 bolts. Furthermore, the influence of the heating-cooling process on the microstructure and failure mode of bolts was investigated. The obtained data show that Grade 10.9 bolts experience rapid decrease in strength at temperatures exceeding 400°C and respectively reach 40% and 5% of their original strength when heated to 600°C and 800°C. Test data also indicate that Grade 10.9 bolts act differently in the cooling phase compared with the heating phase with respect to strength degradation. This is due to the irreversible transformations that occur in the microstructure of bolts when they are exposed to a heating-cooling cycle.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
All data generated or used during the study appear in the published article.
Acknowledgments
The authors would like to thank the Research Council of Shahid Chamran University of Ahvaz (Grant No. SCU.EC98.366) for providing the facilities and financial support needed to conduct this research project.
References
ASTM. 2009. Standard test methods for elevated temperature tension tests of metallic materials. ASTM E21. West Conshohocken, PA: ASTM.
CEN (European Committee for Standardization). 2005. Eurocode 3: Design of steel structures-Part 1.2: General rules-Structural fire design. EN 1993-1-2. Brussels, Belgium: CEN.
Chen, J., B. Young, and B. Uy. 2006. “Behavior of high strength structural steel at elevated temperatures.” J. Struct. Eng. 132 (12): 1948–1954. https://doi.org/10.1061/(ASCE)0733-9445(2006)132:12(1948).
Chiew, S. P., M. S. Zhao, and C. K. Lee. 2014. “Mechanical properties of heat-treated high strength steel under fire/post-fire conditions.” J. Constr. Steel Res. 98 (Jul): 12–19. https://doi.org/10.1016/j.jcsr.2014.02.003.
Choi, I. R., K. S. Chung, and D. H. Kim. 2014. “Thermal and mechanical properties of high-strength structural steel HSA800 at elevated temperatures.” Mater. Des. 63 (Nov): 544–551. https://doi.org/10.1016/j.matdes.2014.06.035.
Craveiro, H. D., J. P. C. Rodrigues, A. Santiago, and L. Laím. 2016. “Review of the high temperature mechanical and thermal properties of the steels used in cold formed steel structures—The case of the S280 Gd+Z steel.” Thin Walled Struct. 98 (Part A): 154–168. https://doi.org/10.1016/j.tws.2015.06.002.
Eslami, M., A. Rezaeian, and V. Kodur. 2018. “Behavior of steel column-trees under fire conditions.” J. Struct. Eng. 14 (9): 04018135. https://doi.org/10.1061/(ASCE)ST.1943-541X.0002135.
Guo, Z., X. Jia, and W. Qiao. 2019. “Mechanical properties of butt weldments made with q345b steel and e5015 electrodes at different temperatures.” J. Mater. Civ. Eng. 31 (9): 04019185. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002845.
Hanus, F., G. Zilli, and J. M. Franssen. 2011. “Behaviour of Grade 8.8 bolts under natural fire conditions—Tests and model.” J. Constr. Steel Res. 67 (8): 1292–1298. https://doi.org/10.1016/j.jcsr.2011.03.012.
Hou, X., W. Zheng, V. Kodur, and H. Sun. 2014. “Effect of temperature on mechanical properties of prestressing bars.” Constr. Build. Mater. 61 (Jun): 24–32. https://doi.org/10.1016/j.conbuildmat.2014.03.001.
Hu, Y., L. Shen, S. Nie, B. Yang, and W. Sha. 2016. “FE simulation and experimental tests of high-strength structural bolts under tension.” J. Constr. Steel Res. 126 (Nov): 174–186. https://doi.org/10.1016/j.jcsr.2016.07.021.
Kawohl, A. K., and J. Lange. 2015. “Test on 10.9 bolts under combined tension and shear during and after fire.” J. App. Struct. Fire Eng. https://doi.org/10.14311/asfe.2015.050.
Kirby, B. R. 1995. “The behaviour of high-strength grade 8.8 bolts in fire.” J. Constr. Steel Res. 33 (1–2): 3–38. https://doi.org/10.1016/0143-974X(94)00013-8.
Kirby, B. R., and R. R. Preston. 1988. “High temperature properties of hot rolled, structural steels for use in fire engineering design studies.” Fire Saf. J. 13 (1): 27–37. https://doi.org/10.1016/0379-7112(88)90030-6.
Kodur, V., M. Dwaikat, and R. Fike. 2010. “High-temperature properties of steel for fire resistance modeling of structures.” J. Mater. Civ. Eng. 22 (5): 423–434. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000041.
Kodur, V., S. Kand, and W. Khaliq. 2012. “Effect of temperature on thermal and mechanical properties of steel bolts.” J. Mater. Civ. Eng. 24 (6): 765–774. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000445.
Kodur, V., M. Yahyai, A. Rezaeian, M. Eslami, and A. Poormohamadi. 2017. “Residual mechanical properties of high strength steel bolts subjected to heating-cooling cycle.” J. Constr. Steel Res. 131 (Apr): 122–131. https://doi.org/10.1016/j.jcsr.2017.01.007.
Lange, J., and F. Gonzalez. 2012. “Behavior of high strength grade 10.9 bolts under fire conditions.” Struct. Eng. Int. 22 (4): 470–475. https://doi.org/10.2749/101686612X13363929517451.
Lee, J., and M. D. Engelhardt. 2014. “Pre-yielding effects of ASTM A992 steel at elevated temperatures.” Int. J. Steel Struct. 14 (4): 785–795. https://doi.org/10.1007/s13296-014-1210-2.
Li, G. Q., S. C. Jiang, Y. Z. Yin, K. Chen, and M. F. Li. 2003. “Experimental studies on the properties of constructional steel at elevated temperatures.” J. Struct. Eng. 129 (12): 1717–1721. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:12(1717).
McCann, F., L. Gardner, and S. Kirk. 2015. “Elevated temperature material properties of cold-formed steel hollow sections.” Thin Walled Struct. 90 (May): 84–94. https://doi.org/10.1016/j.tws.2015.01.007.
Meyers, M., and K. Chawla. 2009. Mechanical behavior of materials. New York: Cambridge University Press.
Peixoto, R. M., M. S. Seif, and L. C. M. Vieira Jr. 2017. “Double-shear tests of high-strength structural bolts at elevated temperatures.” Fire Saf. J. 94 (Dec): 8–21. https://doi.org/10.1016/j.firesaf.2017.09.003.
Rezaeian, A., M. Keshavarz, and E. Hajjari. 2019. “Mechanical properties of steel welds at elevated temperatures.” J. Constr. Steel Res. 105853. https://doi.org/10.1016/j.jcsr.2019.105853.
Rezaeian, A., and M. Yahyai. 2015. “Fire response of steel column-tree moment resisting frames.” Mater. Struct. 48 (6): 1771–1784. https://doi.org/10.1617/s11527-014-0271-1.
Santiago, A., L. S. Da Silva, P. V. Real, G. Vaz, and A. G. Lopes. 2009. “Experimental evaluation of the influence of connection typology on the behaviour of steel structures under fire.” Eng. J. 46 (2): 81–98.
Selden, K. L., E. C. Fischer, and A. H. Varma. 2015. “Experimental investigation of composite beams with shear connections subjected to fire loading.” J. Struct. Eng. 142 (2): 04015118. https://doi.org/10.1061/(ASCE)ST.1943-541X.0001381.
Shirih, A., A. Rahman, and M. Mahamid. 2016. “Behavior of ASTM A325 bolts under simulated fire conditions: Experimental investigation.” J. Struct. Fire Eng. 8 (4): 377–391. https://doi.org/10.1108/JSFE-06-2016-0005.
Wang, W., K. Wang, V. Kodur, and B. Wang. 2018. “Mechanical properties of high-strength Q690 steel at elevated temperature.” J. Mater. Civ. Eng. 30 (5): 04018062. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002244.
Yahyai, M., V. Kodur, and A. Rezaeian. 2018. “Residual mechanical properties of high-strength steel bolts after exposure to elevated temperature.” J. Mater. Civ. Eng. 30 (10): 04018240. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002416.
Yahyai, M., and A. Rezaeian. 2015. “Behavior of beams in bolted column-tree frames at elevated temperature.” Fire Mater. 40 (3): 482–497. https://doi.org/10.1002/fam.2305.
Yang, K. C., R. J. Hsu, and Y. J. Chen. 2011. “Shear strength of high-strength bolts at elevated temperature.” Constr. Build. Mater. 25 (8): 3656–3660. https://doi.org/10.1016/j.conbuildmat.2011.03.003.
Yu, L., and K. H. Frank. 2009. “Shear behavior of A325 and A490 high-strength bolts in fire and post-fire.” Eng. J. Am. Inst. Steel Constr. Inc. 46 (2): 99–106.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Oct 22, 2019
Accepted: Feb 11, 2020
Published online: Jun 22, 2020
Published in print: Sep 1, 2020
Discussion open until: Nov 22, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.