Shear Properties of Eastern Hemlock with Respect to Fiber Orientation for Use in Cross Laminated Timber
Publication: Journal of Materials in Civil Engineering
Volume 32, Issue 7
Abstract
Shear properties of the cross layer in cross laminated timber (CLT) panels are critical for design purposes, especially for applications with high concentrated loads and low span-to-depth ratios. Understanding how the shear properties of CLT lamstock vary with respect to fiber orientation—from perpendicular-to-grain (90°) to parallel-to-grain (0°)—can lead to new and innovative panel layups with superior shear performance. In this study, two-plate shear specimens (per the relevant standard) were fabricated with fiber orientations of 0°, 30°, 45°,60°, and 90° with respect to the shear load direction using eastern hemlock lumber. Both shear modulus and shear strength were measured as a function of fiber orientation. The influence of fiber orientation and the interaction of resisting components on the shear properties are discussed concerning observations of the types of failure modes. The results indicate that the effective shear stiffness () and the characteristic shear strength () for a traditional (90°) CLT panel made from eastern hemlock would satisfy grade E3 CLT per the relevant standard. Moreover, the shear strength of the angled cross layers with 30° and 45° fiber orientation with respect to the major panel axis would be 98% and 59% higher, respectively, than CLT with a 90° cross layer orientation.
Get full access to this article
View all available purchase options and get full access to this article.
Data Availability Statement
Some or all data, models, or code that support the findings of this study are available from the corresponding author upon reasonable request, including the load-deflection response of the planar shear test for 0°, 30°, 45°, 60°, and 90° specimens.
Acknowledgments
This research was generously supported by the Massachusetts Executive Office of Energy and Environmental Affairs (EOEEA) Award No. 117-1855. The authors also thank technical laboratory assistant, Mr. Seth Lawrence, and research assistant, Mr. Eric Waterman, for their technical support.
References
Aicher, S., Z. Christian, and M. Hirsch. 2016. “Rolling shear modulus and strength of beech wood laminations.” Holzforschung 70 (8): 773–781. https://doi.org/10.1515/hf-2015-0229.
ANSI/APA (American National Standards Institute/American Psychological Association). 2018. Standard for performance-rated cross laminated timber. ANSI/APA PRG 320. New York: ANSI/APA.
ASTM. 2010. Practice for sampling and data-analysis for structural wood and wood-based products. ASTM D2915. West Conshohocken, PA: ASTM.
ASTM. 2011. Standard test methods for structural panels in planar shear (rolling shear). ASTM D2718-00. West Conshohocken, PA: ASTM.
ASTM. 2014. Standard test methods for small clear specimens of timber. ASTM D143. West Conshohocken, PA: ASTM.
Awaludin, A., W. Smittakorn, T. Hirai, and T. Hayashikawa. 2007. “Bearing properties of Shorea obtusa beneath a laterally loaded bolt.” J. Wood Sci. 53 (3): 204–210. https://doi.org/10.1007/s10086-006-0842-z.
Bendtsen, B. A. 1976. “Rolling shear characteristics of nine structural softwoods.” For. Prod. J. 26 (11): 51–56. https://doi.org/10.1007/s10086-006-0842-z.
Blaß, H. J., and R. Görlacher. 2000. “Rolling shear in structural bonded timber elements.” In Vol. 5 of Paper Presented at the Annales GC Bois, 1–5. Paris: IRABOIS.
Brandner, R. 2013. “Production and technology of cross laminated timber (CLT): A state-of-the-art report.” In Proc., Focus Solid Timber Solutions—European Conf. on Cross Laminated Timber (CLT). Bath, UK: Univ. of Bath.
Clouston, P., and A. Schreyer. 2016. “UMass design building: A catalyst for regional change.” In Proc., World Conf. on Timber Engineering (WCTE 2016). Vienna, Austria: Vienna Univ. of Technology. https://www.researchgate.net/profile/Alexander_C_Schreyer/publication/308887723_UMass_Design_Building_A_Catalyst_for_Regional_Change/links/57f4c68808ae280dd0b8a0a0.pdf.
Fellmoser, P., and H., Blaß. 2004. “Influence of rolling shear modulus on strength and stiffness of structural bonded timber elements.” In Vol. 37 of Proc., CIB-W18 Meeting. Delft, Netherlands: CIB International Council for Research and Innovation. http://holz.vaka.kit.edu/public/40.pdf.
Flores, E. S., K. Saavedra, J. Hinojosa, Y. Chandra, and R. Das. 2016. “Multi-scale modelling of rolling shear failure in cross-laminated timber structures by homogenisation and cohesive zone models.” Int. J. Solids Struct. 81 (Mar): 219–232. https://doi.org/10.1016/j.ijsolstr.2015.11.027.
Gagnon, S., and C. Pirvu. 2011. Cross laminated timber (CLT) handbook. Vancouver, Canada: FPInnovations.
Gardner, D. J., and J. F. Diebel. 1995. “Eastern Hemlock (Tsuga canadensis) uses and properties.” In Proc., Hemlock Ecology and Management Conf. Madison, WI: Univ. of Wisconsin.
Gong, M., D. Y. Tu, L. Li, and Y. H. Chui. 2015. “Planar shear properties of hardwood cross layer in hybrid cross laminated timber.” In Proc., 5th Int. Scientific Conf. on Hardwood Processing. Quebec City, Canada: FPInnovations. https://www.researchgate.net/profile/Trinh_Hien_Mai/publication/337413670_Bai_bao_12_-_ischp2015-proceedings/links/5dd60618299bf11ec866e37d/Bai-bao-12-ischp2015-proceedings.pdf#page=85.
Hankinson, R. 1921. “Investigation of crushing strength of spruce at varying angles of grain.” Air Serv. Inf. Circ. 3 (259): 130.
Hindman, D. P., and J. C. Bouldin. 2014. “Mechanical properties of southern pine cross-laminated timber.” J. Mater. Civ. Eng. 27 (9): 04014251. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001203.
Kim, K. Y. 2007. “A note on the Hankinson formula.” Wood Fiber Sci. 18 (2): 345–348.
Kollmann, F. F. P., and W. A. Côté. 1968. Principles of wood science. I: Solid wood. Berlin: Springer.
Lam, F., Y. Li, and M. Li. 2016. “Torque loading tests on the rolling shear strength of cross-laminated timber.” J. Wood Sci. 62 (5): 407–415. https://doi.org/10.1007/s10086-016-1567-2.
Li, Y. 2015. “Duration-of-load and size effects on the rolling shear strength of cross laminated timber.” Ph.D. dissertation, Dept. of Wood Science, Univ. of British Columbia.
Munthe, B., and R. L. Ethington. 1968. Method for evaluating shear properties of wood. Madison, WI: US Dept. of Agriculture, Forest Service, Forest Products Laboratory.
NDS (National Design Specification). 2018. National design specification for wood construction. Washington, DC: American Forest and Paper Association.
NeLMA (Northeastern Lumber Manufacturers Association). 2017. “2017 standard grading rules for northeastern lumber.” Accessed November 1, 2017. https://www.nelma.org/library/2013-standard-grading-rules-for-northeastern-lumber.
Papadopoulos, A. S. 1978. “The Burr distribution as a failure model from a Bayesian approach.” IEEE Trans. Reliab. R-27 (5): 369–371. https://doi.org/10.1109/TR.1978.5220427.
Pugel, A. D. 1990. “Angle-to-grain tensile strength specimen for thin wood samples.” For. Prod. J. 40 (2): 49–51.
Ross, R. J. 2010. Wood handbook: Wood as an engineering material.
Sikora, K. S., D. O. McPolin, and A. M. Harte. 2016. “Effects of the thickness of cross-laminated timber (CLT) panels made from Irish Sitka spruce on mechanical performance in bending and shear.” Constr. Build. Mater. 116 (Jul): 141–150. https://doi.org/10.1016/j.conbuildmat.2016.04.145.
Steiger, R., and A. Gülzow. 2010. “Validity of bending tests on strip-shaped specimens to derive bending strength and stiffness properties of cross-laminated solid timber (X-lam).” In The future of quality control for wood and wood products, 4–7. Delft, Netherlands: CIB International Council for Research and Innovation.
Steiger, R., A. Gülzow, and D. Gsell. 2008. Non-destructive evaluation of elastic material properties of cross-laminated timber (CLT).” In Vol. 53 of Proc., Conf. COST E, 29–30. Delft, Netherlands: CIB International Council for Research and Innovation. https://www.dora.lib4ri.ch/empa/islandora/object/empa%3A8637/datastream/PDF/Steiger-2008-Non_destructive_evaluation_of_elastic-%28published_version%29.pdfhttps://www.dora.lib4ri.ch/empa/islandora/object/empa%3A8637/datastream/PDF/Steiger-2008-Non_destructive_evaluation_of_elastic-%28published_version%29.pdf.
Tadikamalla, P. R. 1980. “A look at the Burr and related distributions.” Int. Stat. Rev. 48 (3): 337–344. https://doi.org/10.2307/1402945.
USDA Forest Service. 2013. “Hemlock woolly adelgid coordinated commitment to improved management and restoration of hemlock: 2014–2018.” Accessed December 4, 2019. http://www.michigandnr.com/FTP/forestry/Mech/FHH/2013/hwa/Article/HWA%20National%20Initiative%20Strategic%20Plan%202014-18.pdf.
Wang, Z., H. Fu, M. Gong, J. Luo, W. Dong, T. Wang, and Y. H. Chui. 2017. “Planar shear and bending properties of hybrid CLT fabricated with lumber and LVL.” Constr. Build. Mater. 151 (Oct): 172–177. https://doi.org/10.1016/j.conbuildmat.2017.04.205.
Winn, M. F., and P. A. Araman. 2005. “Study of the utilization options for dead and dying Eastern Hemlock in the southern Appalachians.” In Proc., 3rd Symp. on Hemlock Woolly Adelgid in the Eastern United States, 360–363. Hà Nội, Vietnam: Vietnam National Univ. of Forestry. https://www.fs.fed.us/foresthealth/technology/pdfs/3rdSymposiumHWA05_01.pdf#page=374.
Yawalata, D., and F. Lam. 2011. Development of technology for cross laminated timber building systems. Vancouver, Canada: FPInnovation.
Yoshihara, H., and M. Yoshinobu. 2014. “Off-axis tensile strength and evaluation of the in-plane shear strength of paper.” Holzforschung 68 (5): 583–590. https://doi.org/10.1515/hf-2013-0163.
Zhou, Q., M. Gong, Y. H. Chui, and M. Mohammad. 2014a. “Measurement of rolling shear modulus and strength of cross-laminated timber fabricated with black spruce.” Constr. Build. Mater. 64 (Aug): 379–386. https://doi.org/10.1016/j.conbuildmat.2014.04.039.
Zhou, Q., M. Gong, Y. H. Chui, and M. Mohammad. 2014b. “Measurement of rolling shear modulus and strength of cross-laminated timber using bending and two-plate shear tests.” Wood Fiber Sci. 46 (2): 259–269.
Information & Authors
Information
Published In
Copyright
©2020 American Society of Civil Engineers.
History
Received: Mar 7, 2019
Accepted: Dec 16, 2019
Published online: Apr 22, 2020
Published in print: Jul 1, 2020
Discussion open until: Sep 22, 2020
Authors
Metrics & Citations
Metrics
Citations
Download citation
If you have the appropriate software installed, you can download article citation data to the citation manager of your choice. Simply select your manager software from the list below and click Download.